journal article·2012-03

Cutting Performance of WC-Co Alloys Modified by Nano-Additives

You Wang, Zhaoyi Pan, Chengbiao Wang, Xiaoguang Sun, Zhijian Peng, Baolin Wang

Publisher page

Abstract

In this paper, the microstructure of WC-Co alloys with and without nano-additives was characterized by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The hardness and fracture toughness was tested by using a Vickers hardness tester and a universal testing machine. The cutting test was carried out at different feed velocities (250 r/min and 320 r/min), and the contact pairs are cutting tools and 45# steel bars. Results showed that the hardness and fracture toughness of WC-Co cemented carbides with nano-additives are higher than that of WC-Co cemented carbides without nano-additives, and they are increased 10.21% and 19.69%, respectively. The flank worn width and crater width of cutting tools decrease greatly with the addition of nano-additives. For the nano-modified specimen with WC grain size of 7 μ m , both the flank worn width and crater width are the minimum after the cutting process. And there are little built-up layers and some pile-up regions on the flank face leading to high cutting performance for the nano-modified cemented carbides. There are some melted regions on the flank face of cutting tools without nano-additives, and the WC grains on the cross section of alloys without nano-additives show severe fragmentation. The wear type of WC-Co is flank wear, and the wear mechanism is abrasive, adhesion and oxidation wear.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced materials and composites · Tunneling and Rock Mechanics · Diamond and Carbon-based Materials Research

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (23)

Show source-provided references
1. Liu · J. Alloy. Compd. · 2007 · 458 · 36610.1016/j.jallcom.2007.03.107 ↗
2. Cha · Mater. Sci. Eng. A · 2003 · 351 · 3110.1016/S0921-5093(02)00605-6 ↗
3. Juhr · J. Mater. Process. Technol. · 2004 · 149 · 17810.1016/j.jmatprotec.2004.02.037 ↗
4. Shen · J. Mater. Sci. Technol · 2004 · 20 · 7
5. Gee · Wear · 2007 · 263 · 13710.1016/j.wear.2006.12.046 ↗
6. Llanes · Acta Mater. · 2002 · 50 · 238110.1016/S1359-6454(02)00071-X ↗
7. Bonny · Wear · 2010 · 268 · 150410.1016/j.wear.2010.02.029 ↗
8. Lima · Thin Solid Films · 2002 · 416 · 12910.1016/S0040-6090(02)00631-4 ↗
9. Xu · Int. J. Refract. Met. Hard Mater. · 2001 · 19 · 15910.1016/S0263-4368(01)00018-X ↗
10. Petch · J. Iron Steel Ins. · 1953 · 174 · 25
11. Shi · J. Mater. Sci. Technol · 2005 · 21 · 353
12. Cha · Mater. Sci. Eng. A · 2008 · 486 · 40410.1016/j.msea.2007.09.023 ↗
13. Li · Surf. Coat. Technol. · 2005 · 194 · 9610.1016/j.surfcoat.2004.04.075 ↗
14. Abdel-Aal · Wear · 2008 · 265 · 167010.1016/j.wear.2008.04.004 ↗
15. Farhat · Mater. Charact. · 2003 · 51 · 11710.1016/j.matchar.2003.10.005 ↗
16. Allen · Wear · 2001 · 250 · 60410.1016/S0043-1648(01)00667-6 ↗
17. Bonny · Wear · 2010 · 268 · 150410.1016/j.wear.2010.02.029 ↗
18. Zhao · J. Refract. Met. Hard Mater. · 2010 · 28 · 33010.1016/j.ijrmhm.2009.11.007 ↗
19. H.F. Fischmeister and L.R. Olson: in Proc. Int. Conf. on Cutting Tool Mater., September 15-17, Ft. Mitchell, Kentucky, 1980, 111.
20. Karagoz · Steel Res. · 1987 · 58 · 35310.1002/srin.198700231 ↗
21. P. Billgren: in Proc. First Int. on High Speed Steel Conf., March, 26-29, Leoben, Austria, 1990, 115-122.
22. Leskovšek · J. Mater. Process. Technol. · 2006 · 178 · 32810.1016/j.jmatprotec.2006.04.016 ↗
23. Chenje · Mater. Design · 2004 · 25 · 1110.1016/S0261-3069(03)00168-7 ↗