Correlating diameter, mechanical and structural properties of poly(l-lactide) fibres from needleless electrospinning
Source abstract
Abstract
The development and application of nanofibres requires a thorough understanding of the mechanical properties on a single fibre level including respective modelling tools for precise fibre analysis. This work presents a mechanical and morphological study of poly-l-lactide nanofibres developed by needleless electrospinning. Atomic force microscopy (AFM) and micromechanical testing (MMT) were used to characterise the mechanical response of the fibres within a diameter range of 200-1400 nm. Young's moduli E determined by means of both methods are in sound agreement and show a strong increase for thinner fibres below a critical diameter of 800 nm. Similar increasing trends for yield stress and hardening modulus were measured by MMT. Finite element analyses show that the common practice of modelling three-point bending tests with either double supported or double clamped beams is prone to significant bias in the determined elastic properties, and that the latter is a good approximation only for small diameters. Therefore, an analytical formula based on intermediate boundary conditions is proposed that is valid for the whole tested range of fibre diameters, providing a consistently low error in axial Young's modulus below 10%. The analysis of fibre morphology by differential scanning calorimetry and 2D wide-angle X-ray scattering revealed increasing polymer chains alignment in the amorphous phase and higher crystallinity of fibres for decreasing diameter. The combination of these observations with the mechanical characterisation suggests a linear relationship between Young's modulus and both crystallinity and molecular orientation in the amorphous phase. STATEMENT OF SIGNIFICANCE: Fibrous membranes have rapidly growing use in various applications, each of which comes with specific property requirements. However, the development and production of nanofibre membranes with dedicated mechanical properties is challenging, in particular with techniques suitable for industrial scales such as needleless electrospinning. It is therefore a key step to understand the mechanical and structural characteristics of single nanofibres developed in this process, and to this end, the present work presents changes of internal fibre structure and mechanical properties with diameter, based on dedicated models. Special attention was given to the commonly used models for analyzing Young's modulus of single nanofibers in three-point bending tests, which are shown to be prone to large errors, and an improved robust approach is proposed.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Electrospun Nanofibers in Biomedical Applications · biodegradable polymer synthesis and properties · Silk-based biomaterials and applications
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (64)
Show source-provided references
1. Applications of electrospun nanofibers10.1007/s11434-008-0319-0 ↗
2. Biomaterials BMP-2 plasmid loaded PLGA/HAp composite scaffolds for treatment of bone defects in nude mice10.1016/j.biomaterials.2008.10.029 ↗
3. Nanofibers for drug delivery - incorporation and release of model molecules, influence of molecular weight and polymer structure10.3762/bjnano.6.198 ↗
4. Biomedical applications of nanofibers10.1002/pat.1813 ↗
5. Cell infiltrative hydrogel fibrous scaffolds for accelerated wound healing10.1016/j.actbio.2016.11.017 ↗
6. Covalent immobilisation of VEGF on plasma-coated electrospun scaffolds for tissue engineering applications10.1016/j.colsurfb.2014.10.016 ↗
7. Preparation and characterization of electrospun alginate/PLA nanofibers as tissue engineering material by emulsion eletrospinning10.1016/j.jmbbm.2016.09.012 ↗
8. Dual electrospinning with sacrificial fibers for engineered porosity and enhancement of tissue ingrowth
9. Electrospraying of microfluidic encapsulated cells for the fabrication of cell-laden electrospun hybrid tissue constructs10.1016/j.actbio.2017.10.012 ↗
10. Computational predictions of the tensile properties of electrospun fiber meshes: effect of fiber diameter and fiber orientation10.1016/j.jmbbm.2008.01.003 ↗
11. B.R. Neugirg, S.R. Koebley, C. Schniepp, A. Fery, AFM-based mechanical characterization of single nano fibres (2016) 8414–8426. http://doi.org/10.1039/c6nr00863a.10.1039/C6NR00863A ↗
12. Tensile versus AFM testing of electrospun PVA nanofibers: bridging the gap from Microscale to nanoscale
13. Effects of annealing on the structural and mechanical properties of electrospun polymeric nanofibres10.1088/0957-4484/17/10/034 ↗
14. Nanomechanical properties of supramolecular self-assembled whiskers determined by AFM force mapping10.1021/la904780c ↗
15. Measurement of the elastic modulus of spider mite silk fibers using atomic force microscopy10.1063/1.4800865 ↗
16. A generalized description of the elastic properties of nanowires
17. Elastic modulus of single cellulose microfibrils from tunicate measured by atomic force
18. Size dependent mechanical properties of electrospun polymer fibers from a composite structure10.1016/j.polymer.2012.08.064 ↗
19. Determining the mechanical properties of electrospun poly-ε-caprolactone (PCL) nanofibers using AFM and a novel fiber anchoring technique10.1016/j.msec.2015.09.102 ↗
20. D. Papkov, Y. Zou, M.N. Andalib, A. Goponenko, S.Z.D. Cheng, Y.A. Dzenis, Simultaneously strong and tough ultra fine continuous nano fibers, (2013) 3324–3331. http://doi.org/10.1021/nn400028p.10.1021/nn400028p ↗
21. Tensile testing of a single ultrafine polymeric fiber10.1016/j.biomaterials.2004.05.021 ↗
22. Elastic–plastic behavior of non-woven fibrous mats10.1016/j.jmps.2011.10.007 ↗
23. The design trend in tissue-engineering scaffolds based on nanomechanical properties of individual electrospun nanofibers10.1016/j.ijpharm.2013.06.083 ↗
24. Orientation and partial disentanglement in individual electrospun fibers: diameter dependence and correlation with mechanical properties10.1021/acs.macromol.5b00994 ↗
25. Effect of supramolecular structure on polymer nanofibre elasticity10.1038/nnano.2006.172 ↗
26. C.T. Lim, E.P.S. Tan, S.Y. Ng, C.T. Lim, E.P.S. Tan, S.Y. Ng, Effects of crystalline morphology on the tensile properties of electrospun polymer nanofibers 141908 (2008) 2006–2009. http://doi.org/10.1063/1.2857478.10.1063/1.2857478 ↗
27. Effect of fiber diameter on tensile properties of electrospun poly(ε-caprolactone)10.1016/j.polymer.2008.08.022 ↗
28. Structure and properties of electrospun PLLA single nanofibres10.1088/0957-4484/16/2/005 ↗
29. Tensile testing of individual ultrathin electrospun poly(L-lactic acid) fibers10.1002/app.30959 ↗
30. Mechanical property enhancement of polylactide nano fi bers through optimization of molecular weight, electrospinning conditions, and stereocomplexation10.1021/ma300289z ↗
31. G. Yazgan, R.I. Dmitriev, V. Tyagi, J. Jenkins, M. Rottmar, R.M. Rossi, C. Toncelli, D.B. Papkovsky, K. Maniura-weber, G. Fortunato, Steering surface topographies of electrospun fibers: understanding the mechanisms, (2017) 1–13. http://doi.org/10.1038/s41598-017-00181-0.10.1038/s41598-017-00181-0 ↗
32. Single electrospun PLLA and PCL polymer nanofibers: increased molecular orientation with decreased fiber diameter10.1016/j.polymer.2017.04.070 ↗
33. Orientation of poly(vinyl alcohol) nanofiber and crystallites in non-woven electrospun nanofiber mats under uniaxial stretching
34. Orientation analysis of individual electrospun PE nanofibers by transmission electron microscopy10.1016/j.polymer.2010.03.031 ↗
35. Mechanical testing of electrospun PCL fibers10.1016/j.actbio.2011.08.015 ↗
36. An overview of mechanical properties and material modeling of polylactide (PLA) for medical applications10.1007/s10439-015-1455-8 ↗
37. Computational and experimental investigation into mechanical performances of Poly-L-Lactide Acid (PLLA) coronary stents10.1016/j.jmbbm.2016.08.033 ↗
38. G. Stoclet, R. Seguela, J. Lefebvre, C. Rochas, New Insights on the Strain-Induced Mesophase of Poly(D, L-lactide): In Situ WAXS and DSC Study of the Thermo-Mechanical Stability, (2010) 7228–7237. http://doi.org/10.1021/ma101430c.10.1021/ma101430c ↗
39. Relationship between the rigid amorphous phase and mesophase in electrospun fi bers10.1016/j.polymer.2013.03.019 ↗
40. Direct investigations on strain-induced cold crystallization behavior and structure evolutions in amorphous poly(lactic acid) with SAXS and WAXS measurements10.1016/j.polymer.2016.03.014 ↗
41. Deformation and structure evolution of glassy poly(lactic acid) below the glass transition10.1039/C5CE00669D ↗
42. A 2.5D approach to the mechanics of electrospun fibre mats10.1039/C7SM01241A ↗
43. NIH Image to ImageJ: 25 years of image analysis10.1038/nmeth.2089 ↗
44. Calculation of thermal noise in atomic force microscopy10.1088/0957-4484/6/1/001 ↗
45. Structural Analysis with the Finite Element Method - Linear Statics: Volume 2: beams, plates and
46. Timoshenko beam-bending solutions in terms of euler-bernoulli solutions
47. W. Weaver, J.M. Gere, Matrix Analysis of Framed Structures, 1990. http://doi.org/10.1007/978-1-4684-7487-9.10.1007/978-1-4684-7487-9 ↗
48. Characterisation and modelling of the elastic properties of poly(lactic acid) nanofibre scaffolds10.1007/s10853-013-7644-7 ↗
49. D. Garlotta, A Literature Review of Poly(Lactic Acid), 9 (2002).10.1023/A:1020200822435 ↗
50. A simple modification method to obtain anisotropic and porous 3D microfibrillar scaffolds for surgical and biomedical applications
51. Small-angle scattering studies on carbonized cellulose fibers*10.1002/polc.5070280113 ↗
52. Microvoids in polyacrylonitrile fibers: a small-angle X-ray scattering study10.1021/ma991427x ↗
53. Structure and process relationship of electrospun bioabsorbable nanofiber membranes10.1016/S0032-3861(02)00275-6 ↗
54. Drawing and annealing of nylon-6 fibers - studies of crystal-growth, orientation of amorphous and crystalline domains and their influence on properties10.1016/0032-3861(95)99780-X ↗
55. Hermans · 1946
56. Electrospinning as a new technique to control the crystal morphology and molecular orientation of polyoxymethylene nanofibers10.1021/ja804185s ↗
57. Cold Crystallization of PLLA Studied by Simultaneous SAXS and WAXS10.1002/mame.200400097 ↗
58. Disorder-to-order phase transition and multiple melting behavior of poly(L-lactide) investigated by simultaneous measurements of WAXD and DSC10.1021/ma0706071 ↗
59. Mass production of nanofibrous extracellular matrix with controlled 3D morphology for large-scale soft tissue regeneration10.1089/ten.tec.2012.0417 ↗
60. Manufacturing scale-up of electrospun poly(vinyl alcohol) fibers containing tenofovir for vaginal drug delivery10.1016/j.ijpharm.2014.08.039 ↗
61. On the importance of boundary conditions on nanomechanical bending behavior and elastic modulus determination of silver nanowires
62. The Young’s modulus of a microcrystalline cellulose10.1023/A:1013181804540 ↗
63. Deformation-mediated superstructures and cavitation of poly(L-lactide): in-situ small-angle X-ray scattering study10.1016/j.polymer.2011.12.002 ↗
64. G. Stoclet, R. Seguela, C. Vanmansart, C. Rochas, J. Lefebvre, WAXS study of the structural reorganization of semi-crystalline polylactide under tensile drawing, 53 (2012) 519–528. http://doi.org/10.1016/j.polymer.2011.11.063.10.1016/j.polymer.2011.11.063 ↗