Effect of the porous electrode geometry on the freezing of supercooled water
Source abstract
Abstract
The supercooled water characteristics in porous electrodes, affect the proton exchange membrane fuel cell (PEMFC) cold starting. This study analyzed the uneven substrate geometry, specifically, the influence of the contact angle and substrate angle on the solidification nucleation rate. For a given temperature, the nucleation rate decreases with increasing contact angle, with less effect as the contact angle exceeds 150°. Experiments observing the freezing of supercooled water in a detached catalyst layer confirmed this result. The simulation also showed that the nucleation rate decreases exponentially with increasing substrate angle: at the 15 K supercooling, with substrate angles increasing by 20°, nucleation rates have a difference of about 10 −11 times. Thus, the effect of the substrate geometry cannot be ignored during the freezing of supercooled water in a porous electrode.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Fuel Cells and Related Materials · Electrocatalysts for Energy Conversion · Phase Change Materials Research
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (32)
Show source-provided references
1. A review on lifetime prediction of proton exchange membrane fuel cells system10.1016/j.jpowsour.2022.231256 ↗
2. The key materials and components for proton exchange membrane fuel cell
3. Cold start behavior and freeze characteristics of a polymer electrolyte membrane fuel cell10.1002/fuce.202000106 ↗
4. New roads and challenges for fuel cells in heavy-duty transportation10.1038/s41560-021-00775-z ↗
5. An efficient cold start strategy for proton exchange membrane fuel cell stacks10.1016/j.jpowsour.2022.231492 ↗
6. Hydrogen starvation mitigation strategies during the start-up of proton exchange membrane fuel cell stack10.1016/j.jpowsour.2021.230809 ↗
7. Investigation on the temperature uniformity and efficiency of cold start-up for proton exchange membrane fuel cell stack based on catalytic hydrogen/oxygen method10.1016/j.jpowsour.2021.229755 ↗
8. Cold start of PEMFC using alternating hydrogen pump: Part I. Mechanistic modeling10.1149/1945-7111/ac6f86 ↗
9. Cold start of a PEMFC using alternating hydrogen pump: Part II. Optimization and comparison with rapid self-heating10.1149/1945-7111/acbb33 ↗
10. The behavior of water below the freezing point in PEFCs10.1016/j.jpowsour.2006.08.026 ↗
11. Freezing characteristics of supercooled water in gas diffusion layer of proton exchange membrane fuel cells10.1016/j.ijhydene.2023.03.294 ↗
12. Supercooled water behavior inside polymer electrolyte fuel cell cross-section below freezing temperature10.1016/j.jpowsour.2008.01.031 ↗
13. Ice Formation during PEM fuel cell cold start: acceptable or not10.1002/advs.202302151 ↗
14. Ice Formation from a supercooled state and water transport through ionomers during PEFC cold startup
15. Influences of super-cooled water on PEMFC sub-freezing startup capability and characteristics
16. Assisted cold start of a PEMFC with a thermochemical preheater: a numerical study10.1016/j.apenergy.2022.120387 ↗
17. Lattice Boltzmann simulation of liquid water transport in gas diffusion layers of proton exchange membrane fuel cells: impact of gas diffusion layer and microporous layer degradation on effective transport properties10.1016/j.jpowsour.2022.232415 ↗
18. Lattice Boltzmann simulation of liquid water transport in gas diffusion layers of proton exchange membrane fuel cells: parametric studies on capillary hysteresis10.1016/j.jpowsour.2022.231381 ↗
19. Lattice Boltzmann simulation of the structural degradation of a gas diffusion layer for a proton exchange membrane fuel cell10.1016/j.jpowsour.2022.232452 ↗
20. Investigation of water freezing in gas diffusion layer of PEMFC using lattice Boltzmann method10.1007/s11581-022-04792-0 ↗
21. On the water transport behavior and phase transition mechanisms in cold start operation of PEM fuel cell10.1016/j.apenergy.2018.10.068 ↗
22. Numerical investigation of cold-start behavior of polymer electrolyte fuel cells in the presence of supercooled water10.1016/j.ijhydene.2018.06.112 ↗
23. Analysis of the failure modes in the polymer electrolyte fuel cell cold-start process—anode dehydration or cathode pore blockage10.3390/en13010256 ↗
24. Theoretical analysis of supercooled states of water generated below the freezing point in a PEFC10.1016/j.ijheatmasstransfer.2014.03.038 ↗
25. Ice-crystallization kinetics in the catalyst layer of a proton-exchange-membrane fuel cell10.1149/2.004403jes ↗
26. Ice crystallization during cold-start of a proton-exchange-membrane fuel cell10.1149/05801.0897ecst ↗
27. Isothermal ice crystallization kinetics in the gas-diffusion layer of a proton-exchange-membrane fuel cell
28. The Johnson-Mehl-Avrami-Kolmogorov model: a brief review10.1007/BF03185527 ↗
29. Investigation of modeling challenges of PEM fuel cells cold start operation10.1016/j.ijhydene.2023.10.188 ↗
30. Two-dimensional simulation of the freezing characteristics in PEMFCs during cold start considering ice crystallization kinetics10.3390/polym14153203 ↗
31. Min · 2007 · 119—172
32. The impact of structural characteristics of the catalyst layer on fuel cell performance based on reconstruction method