journal article·2023-06

Experimental and theoretical investigation of contact resistance in molten carbonate fuel cells

Jaroslaw Milewski, Viktoriya Podhurska, Aliaksandr Martsinchyk, Bogdan Vasyliv, Olaf Dybinski

Publisher page

Abstract

This paper presents the results of experimental and theoretical investigations into the influence of contact force on contact resistance between the current collector and the porous nickel layer of a fuel cell electrode. Two main results were obtained: (i) the greater the force, the lower the contact resistance; (ii) above a certain level, the force applied to the electrode produces no significant change in contact resistance. An MCFC mathematical model was proposed to explain this phenomenon. The model resulted in simulated current-voltage curves obtained for various forces applied to the MCFC and a quantitative assessment of how this resistance affects the performance of the entire fuel cell rather than that of the electrode itself. The results of the study showed significant improvement in MCFC operating parameters due to contact resistance minimization when the compression force is increased to the level of 40 N/cm 2, while further increase of the force beyond that point does not lead to any appreciable improvement in operating parameters.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Fuel Cells and Related Materials · Advancements in Solid Oxide Fuel Cells · Electrocatalysts for Energy Conversion

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (56)

Show source-provided references
1. 2020
2. Catalytic activity of NiO cathode in molten carbonate fuel cells10.1016/j.apcatb.2017.10.003 ↗
3. Microstructure driven design of porous electrodes for molten carbonate fuel cell application: recent progress10.1016/j.ijhydene.2019.12.038 ↗
4. Insight into cathode microstructure effect on the performance of molten carbonate fuel cell10.1016/j.jpowsour.2021.229562 ↗
5. Status report on high temperature fuel cells in Poland – recent advances and achievements10.1016/j.ijhydene.2016.12.087 ↗
6. Microstructure and electrochemical behavior of layered cathodes for molten carbonate fuel cell10.1016/j.jpowsour.2021.229949 ↗
7. Multi-modal porous microstructure for high temperature fuel cell application10.1016/j.jpowsour.2017.11.009 ↗
8. Hybrid molten carbonate fuel cell power plant and multiple-effect desalination system10.1016/j.jclepro.2019.02.215 ↗
9. Thermodynamic, exergoeconomic, and environmental evaluation of a new multi-generation system driven by a molten carbonate fuel cell for production of cooling, heating, electricity, and freshwater10.1016/j.enconman.2019.112040 ↗
10. Preliminary theoretical and experimental analysis of a Molten Carbonate Fuel Cell operating in reversible mode
11. Supporting ionic conductivity of Li2CO3/K2CO3 molten carbonate electrolyte by using yttria stabilized zirconia matrix10.1016/j.ijhydene.2020.12.073 ↗
12. The investigation of cathode layer of Molten Carbonate Fuel Cell manufactured by using printing techniques
13. Zhadan · 2020
14. Vasyliv · 2021 · vol. 1 · 3
15. Modeling the performance of MCFC for various fuel and oxidant compositions10.1016/j.ijhydene.2014.05.151 ↗
16. Study on LiI and KI with low melting temperature for electrolyte replenishment in molten carbonate fuel cells10.1016/j.ijhydene.2019.08.050 ↗
17. Metallic foam supported electrodes for molten carbonate fuel cells10.1016/j.matdes.2020.108864 ↗
18. Milewski J. WM, Ma, BR. A Reduced Order Model of Molten Carbonate Fuel Cell: a Proposal n.D.
19. Full cell mathematical model of a MCFC10.1149/1.1604786 ↗
20. Artificial neural network model of molten carbonate fuel cells: validation on experimental data10.1002/er.4608 ↗
21. Dynamic model of a molten carbonate fuel cell 1 kW stack
22. Numerical analysis of a molten carbonate fuel cell stack in emergency scenarios10.1115/1.4048058 ↗
23. Welding techniques for battery cells and resulting electrical contact resistances10.1016/j.est.2015.04.001 ↗
24. An experimental study determines the electrical contact resistance in resistance welding
25. Designing for the chemical conversion coating with high corrosion resistance and low electrical contact resistance on AZ91D magnesium alloy10.1016/j.corsci.2018.02.051 ↗
26. Contact corrosion resistance between the cathode and current collector plate in the molten carbonate fuel cell10.1149/1.1339027 ↗
27. Behavior and interfacial contact resistance of TiN coated type 316L stainless steel as bipolar plate for proton exchange membrane fuel cell
28. Improved corrosion resistance and interfacial contact resistance of 316L stainless-steel for proton exchange membrane fuel cell bipolar plates by chromizing surface treatment
29. Corrosion properties and contact resistance of TiN, TiAlN and CrN coatings in simulated proton exchange membrane fuel cell environments
30. Corrosion resistance and interfacial contact resistance of TiN coated 316L bipolar plates for proton exchange membrane fuel cell10.1016/j.ijhydene.2011.03.021 ↗
31. Degradation of SS316L bipolar plates in simulated fuel cell environment: corrosion rate, barrier film formation kinetics and contact resistance10.1016/j.jpowsour.2014.02.053 ↗
32. Pre-oxidized and nitrided stainless steel alloy foil for proton exchange membrane fuel cell bipolar plates: Part 1. Corrosion, interfacial contact resistance, and surface structure10.1016/j.jpowsour.2010.03.055 ↗
33. Effect of multilayer CrN/CrAlN coating on the corrosion and contact resistance behavior of 316L SS bipolar plate for high temperature proton exchange membrane fuel cell10.1016/j.jmst.2021.04.043 ↗
34. Stress-dependent electrical contact resistance at fractal rough surfaces
35. Electrical contact resistance considering multi-scale roughness. Electrical Contacts
36. An improved model for predicting electrical contact resistance between bipolar plate and gas diffusion layer in proton exchange membrane fuel cells10.1016/j.jpowsour.2008.03.044 ↗
37. A novel polymer electrolyte fuel cell for laboratory investigations and in-situ contact resistance measurements10.1016/S0013-4686(01)00510-2 ↗
38. Measurement of the electrical contact resistance of PEM fuel cell bipolar plates
39. Study effect of stress in the electrical contact resistance of bipolar plate and membrane electrode assembly in proton exchange membrane fuel cell: a review
40. Multiscale numerical model for contact resistance prediction in the proton exchange membrane fuel cell10.1149/08008.0073ecst ↗
41. Numerical investigation of flow field configuration and contact resistance for PEM fuel cell performance10.1016/j.renene.2007.10.009 ↗
42. Contact resistance prediction of proton exchange membrane fuel cell considering fabrication characteristics of metallic bipolar plates10.1016/j.enconman.2018.05.069 ↗
43. Effect of gas pressure and clamping pressure on interfacial contact resistance of a cylindrical polymer electrolyte membrane fuel cell10.1080/19397038.2021.1986592 ↗
44. Impact of cyclic mechanical compression on the electrical contact resistance between the gas diffusion layer and the bipolar plate of a polymer electrolyte membrane fuel cell10.1016/j.renene.2020.02.033 ↗
45. Effect of surface roughness of composite bipolar plates on the contact resistance of a proton exchange membrane fuel cell10.1016/j.jpowsour.2008.11.063 ↗
46. The surface morphology effects of a metallic bipolar plate on the interfacial contact resistance of a proton exchange membrane fuel cell10.1080/15435075.2012.727114 ↗
47. Study on surface topography of 446M stainless steel as a bipolar plate on interfacial contact resistance of polymer electrolyte membrane fuel cell10.1016/j.jpowsour.2012.07.102 ↗
48. Measuring in situ interfacial contact resistance in a proton exchange membrane fuel cell10.1149/2.1511912jes ↗
49. Contact resistance between gas diffusion layer and catalyst layer of PEM fuel cell10.1016/j.elecom.2007.10.029 ↗
50. Influence of local porosity, local permeability, and contact resistance between the gas diffusion layer and the bipolar plate, on the performances of a polymer electrolyte membrane fuel cell
51. Optimization of contact resistance with better gasketing for a unitized regenerative fuel cell10.1016/j.ijhydene.2018.09.090 ↗
52. Koch · 2002 · vol. 1307
53. The effects of the interconnect rib contact resistance on the performance of planar solid oxide fuel cell stack and the rib design optimization10.1016/j.jpowsour.2008.04.054 ↗
54. Reduction of electrical contact resistance between components of solid oxide fuel cells10.2109/jcersj.111.222 ↗
55. Study of contact resistance at the electrode{\textendash}interconnect interfaces in planar type Solid Oxide Fuel Cells10.1016/j.jpowsour.2013.01.111 ↗
56. A reduced order model of Molten Carbonate Fuel Cell: a proposal10.1016/j.ijhydene.2013.06.002 ↗