journal article·2016-12

Catalytic coating in microstructured devices and their performance in terms of the SO2 oxidation

Walther Benzinger, Oliver Goerke, Peter Pfeifer

Publisher page

Abstract

Microstructured reactors offer several advantages due to their small dimensions and due to their unique heat transfer capabilities. Highly exothermic reactions can be carried out readily in microreactors. In heterogeneous reactions with a catalyst, which is applied as a thin film on the channel walls, the full potential of these microreactors can be utilized. A challenge in the application of the catalyst is whether the microchannel has open ends or whether the microchannel has an opening along the channel axis. The coating is done via the sol–gel route by injecting the liquid precursor into the microchannels or by dropping the liquid precursor onto the microchannels. For the examinations, two types of specimen are coated with Pt/TiO2 gel in two different compositions (2.5 and 10 wt%) in one step. After calcination, the specimen are reduced under flow conditions in 5 vol% H2 in Ar at 773 K for 5 h to obtain Pt(0) from Pt2+. The performance of the catalyst (Pt(0)) is investigated by means of the SO2 oxidation. The results for the oxidation test with the lower concentrated composition show higher conversion values, which can be related to a good dispersion and small particles of the active phase. But differences are found for the tests with the open-ended microchannels, resulting in lower conversion values compared to the microchannels with opening along the channel axis. The influence of the catalyst caused by an insufficient oxidation of the deposited gel, leading to an interaction between support and active component (SMSI) is discussed. The XRD measurements indicate rutile modification as well as large crystallite sizes. Due to this fact, SMSI effect can be excluded and is not responsible for the differences measured in the SO2 conversion. Microprobe analyses determine the distribution of the platinum in the porous titanium dioxide support as uniform. SEM investigations show that the low value in conversion can be related to a non-uniform distribution of the catalyst in the closed microchannels. Considering the drying process in the closed microchannel, an influence of the geometry is obvious. Based on the observation, a model has been developed, which explains qualitatively the distribution of the coating. As a consequence of this model, the coating parameter has to be chosen that no maldistribution occurs. SEM picture showing the maldistribution of the catalytic coating introduced by a sol–gel process in a microstructured channel system of diffusion welded specimen. Drying may be carried out only via the inlets/outlets, which seems to be responsible for the accumulation of coating. The model explains that the contact line moved with time to the center of the microchannel and the deposition takes place at the moving contact line.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Nanomaterials and Printing Technologies · Innovative Microfluidic and Catalytic Techniques Innovation · Catalytic Processes in Materials Science

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (35)

Show source-provided references
1. Kiwi-Minsker L, Renken A (2005) Catal Today 110:2–1410.1016/j.cattod.2005.09.011 ↗
2. Bier W, Keller W, Linder G, Seidel D, Schubert K, Martin H (1993) Chem Eng Process 32:33–4310.1016/0255-2701(93)87004-E ↗
3. Schubert K, Bier W, Brandner J, Fichtner M, Franz C, Linder G (1998) In: 2nd International conference on microreaction technology, Proceedings, New Orleans, pp 88–95
4. Ates A, Goerke O, Pfeifer P (2013) Chem Ing Tech 85(5):664–67210.1002/cite.201200166 ↗
5. Brandner JJ, Bohn L, Henning T, Schygulla U, Schubert K (2007) Heat Transf Eng 28:761–77110.1080/01457630701328528 ↗
6. Gavrilidis A, Angeli P, Cao E, Yeong KK, Wan YSS (2002) Chem Eng Res Des 80(1):3–3010.1205/026387602753393196 ↗
7. Janicke M, Kestenbaum H, Hagendorf U, Schüth F, Fichtner M, Schubert K (2000) J Catal 191:282–29310.1006/jcat.2000.2819 ↗
8. Pfeifer P, Görke O, Schubert K (2002) In: 6th International conference on microreaction technology, Proceedings, New Orleans, 14–10 March 2002, pp 281–287
9. Wunsch R, Fichtner M, Schubert K (2000) 4th International conference on microreaction technology, Proceedings, Atlanta, 6–10 March 2000, pp 481–487
10. Lim MS, Kim MR, Noh J, Woo SI (2005) J Power Sources 140:66–7110.1016/j.jpowsour.2004.08.005 ↗
11. Hench LL, West JK (1990) Chem Rev 90:33–7210.1021/cr00099a003 ↗
12. Pfeifer P, Haas-Santo K, Thormann J, Schubert K (2007) Chim Oggi 2:42–46
13. Pfeifer P, Zscherpe T, Haas-Santo K, Dittmeyer R (2010) Appl Catal A Gen 391:289–29610.1016/j.apcata.2010.06.044 ↗
14. Benzinger W, Wenka A, Dittmeyer R (2011) Appl Catal A Gen 397:209–21710.1016/j.apcata.2011.03.001 ↗
15. Gomez R, Lopez T, Castillo S, Gonzalez RD (1994) J Sol-Gel Sci Technol 1:205–21110.1007/BF00490250 ↗
16. Su C, Hong B-Y, Tseng C-M (2004) Catal Today 96:119–12610.1016/j.cattod.2004.06.132 ↗
17. Wang C-C, Ying JY (1999) Chem Mater 11:3113–312010.1021/cm990180f ↗
18. Bischoff BL, Anderson MA (1995) Chem Mater 7:1772–177910.1021/cm00058a004 ↗
19. Navrotsky A, Kleppa OJ (1967) J Am Ceram Soc 50:626–63010.1111/j.1151-2916.1967.tb15013.x ↗
20. Zhang H, Banfield JF (1998) J Mater Chem 8:2073–207610.1039/a802619j ↗
21. Sanchez E, Lopez T, Gomez R, Bokhimi X, Morales A, Novaro O (1996) J Solid State Chem 122:309–31410.1006/jssc.1996.0118 ↗
22. Bokhimi X, Morales A, Novaro O, Lopez T, Sanchez E, Gomez R (1995) J Mater Res 10(11):2788–279610.1557/JMR.1995.2788 ↗
23. Ertl G, Knözinger H, Schüth F, Weitkamp J (eds) (2008) Handbook of heterogeneous catalysis, vol 4. VCH, Weinheim, pp 1178–1188
24. Tauster SJ, Fung SC, Garten RL (1978) J Am Chem Soc 100:170–17510.1021/ja00469a029 ↗
25. Tauster SJ, Fung SC, Baker RTK, Horsley JA (1981) Science 211(4487):1121–112510.1126/science.211.4487.1121 ↗
26. Bernal S, Calvino JJ, Cauqui MA, Gatica JM, Larese C, Omil JP, Pintado JM (1999) Catal Today 50:175–20610.1016/S0920-5861(98)00503-3 ↗
27. Bonne M, Samoila P, Ekou T, Especel C, Epron F, Marécot P, Royer S, Duprez D (2010) Catal Commun 12:86–9110.1016/j.catcom.2010.08.010 ↗
28. Han W, Lin Z (2012) Angew Chem Int Ed 51:1534–154610.1002/anie.201104454 ↗
29. Adachi E, Dimitrov AS, Nagayama K (1995) Langmuir 11:1057–106010.1021/la00004a003 ↗
30. Lin Y, Balizan E, Lee LA, Niu Z, Wang Q (2010) Angew Chem Int Ed 49:868–87210.1002/anie.200904993 ↗
31. Fischer BJ (2002) Langmuir 18:60–6710.1021/la015518a ↗
32. Pelofsky AH (1966) J Chem Eng Data 11(3):394–39710.1021/je60030a031 ↗
33. Hu H, Larson RG (2005) Langmuir 21:3972–398010.1021/la0475270 ↗
34. Deegan RD, Bakajin O, Dupont TF, Huber G, Nagel SR, Witten TA (1997) Nature 389:827–82910.1038/39827 ↗
35. Leng J (2010) Phys Rev E 82:02140510.1103/PhysRevE.82.021405 ↗