Surface Behavior of AISI H13 Alloy Steel Machining under Environmentally Friendly Cryogenic MQL with PVD-Coated Tool
Source abstract
Abstract
Abstract Cooling and lubrication throughout the machining process have a vital impact on final product quality. Use of cutting fluid in the machining process will not control the increased heat generation that is due to frictional resistance, conventionally. Cryogenic machining along with minimum quantity lubrication (CMQL) is a reliable choice to flood cooling in pertinence. It averts the utilization of a large amount of cutting oil and it improves surface integrity. Carbon dioxide provides better cooling to the tool and work material. Additionally, the vegetable oil droplets provide better lubrication at the interface. The investigation results on the response of CMQL on machinability of AISI H13 steel with varying cutting speeds in the range of 45–75 m/min in end milling uses a PVD-AlTiN–coated carbide insert at a constant depth of cut. Machining with CMQL gives 52–53 % and 38–41 %, 65–71 %, and 33–41 % on cutting temperature and surface roughness, respectively, which is a dwindling value when interrelated with dry and flooded cooling environments, in which cutting forces and flank wear were subsequently reduced moderately when compared to dry and wet machining. Application of CMQL provides exceptional lubrication and cooling to the cutting zone.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Advanced machining processes and optimization · Advanced Machining and Optimization Techniques · Tunneling and Rock Mechanics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Department of Mechanical Engineering, Saveetha Engineering College 1 , Chennai ,
Department of Mechanical Engineering, Saveetha Engineering College 2 , Chennai ,
References (30)
Show source-provided references
1. Potential of Alternative Lubrication Strategies for Metal Cutting Processes: A Review10.1007/s00170-016-9298-5 ↗
2. Titanium Alloys and Their Machinability10.1016/S0924-0136(96)00030-1 ↗
3. Ecological Aspects of the Cutting Fluids and Its Influence on Quantifiable Parameters of the Cutting Processes10.1016/S0924-0136(00)00794-9 ↗
4. Environmentally Friendly Precision Machining10.1080/AMP-200060612 ↗
5. Development of Novel Sustainable Neat-Oil Metal Working Fluids for Stainless Steel and Titanium Alloy Machining. Part 1. Formulation Development10.1007/s00170-006-0585-4 ↗
6. Environmentally Conscious Machining of Difficult-to-Machine Materials with Regard to Cutting Fluids10.1016/j.ijmachtools.2012.02.002 ↗
7. Dry Machining: Machining of the Future10.1016/S0924-0136(00)00445-3 ↗
8. Evaluation of Cryogenic CO2 as a Coolant and Optimization of Surface Roughness in Conventional Milling of HCHCR (AISI D3) Die Steel and CVD Tin Coated Insert Using Taguchi Technique10.18311/jsst/2017/8552 ↗
9. Dry Machining and Minimum Quantity Lubrication10.1016/S0007-8506(07)60027-4 ↗
10. Influence of Minimum Quantity Lubrication Parameters on Tool Wear and Surface Roughness in Milling of Forged Steel10.3901/CJME.2012.03.419 ↗
11. Evaluation of Machinability with MQL System and Effectiveness in Production Lines
12. Transitioning to Sustainable Production - Part I: Application on Machining Technologies10.1016/j.jclepro.2009.08.010 ↗
13. Minimum Quantity Lubricated Grinding of Inconel 751 Alloy10.1080/10426914.2013.763965 ↗
14. Investigation of Effects of Dry and Near Dry Machining on AISI D2 Steel Using Vegetable Oil10.1016/j.jclepro.2013.11.042 ↗
15. Effect of MQL on Surface Roughness in Milling of AA7075-T610.1080/10426910903496821 ↗
16. Experimental and Numerical Investigation of the Effect of Spray Cutting Fluids in High Speed Milling10.1016/j.jmatprotec.2005.08.014 ↗
17. Ti6Al4V Titanium Alloy End Milling with Minimum Quantity of Fluid Technique Use10.1080/10426914.2015.1048367 ↗
18. Environmental Friendly Cutting Fluids and Cooling Techniques in Machining: A Review10.1016/j.jclepro.2014.07.071 ↗
19. Experimental Investigations of Vegetable Based Cutting Fluids with Extreme Pressure during Turning of AISI 304L10.1016/j.triboint.2011.07.012 ↗
20. An Experimental Investigation on Effect of Minimum Quantity Lubrication in Machining AISI 1040 Steel10.1016/j.ijmachtools.2006.09.017 ↗
21. Cooling Techniques for Improved Productivity in Turning10.1016/j.ijmachtools.2008.12.010 ↗
22. Experimental Investigation of Cryogenic Cooling in Milling of AISI D3 Tool Steel10.1080/10426914.2011.654157 ↗
23. Machining of AISI 316 Stainless Steel under Carbon-Di-Oxide Cooling10.1080/10426914.2011.654153 ↗
24. Assessment of Process Improvement Potential of Carbon Dioxide as a Cryogenic for Machining Operations10.4028/www.scientific.net/AMM.856.151 ↗
25. Tool Wear and Cutting Forces under Cryogenic Machining of Titanium Alloy (Ti17)10.1007/s00170-016-9841-4 ↗
26. Experimental and Numerical Study of Chip Formation in Orthogonal Cutting of Ti-5553 Alloy: The Influence of Cryogenic, MQL, and High Pressure Coolant Supply10.1007/s00170-017-0904-y ↗
27. Influence of Cutting Conditions on the Cutting Performance of TiAl6V410.4028/www.scientific.net/AMR.337.387 ↗
28. Effect of the Minimum Quantity Lubrication in High-Speed End-Milling of AISI D2 Cold-Worked Die Steel (62 HRC) by Coated Carbide Tools10.1016/j.surfcoat.2008.06.129 ↗
29. An Analysis of Surface Integrity when Drilling Inconel 718 Using Palm Oil and Synthetic Ester under MQL Condition10.1080/10910344.2011.557967 ↗
30. An Experimental Analysis and Measurement of Process Performances in Machining of Nimonic C-263 Super Alloy10.1016/j.measurement.2012.06.006 ↗