journal article·2021-01-01

Analysis of Phase Transformation and Mechanical Properties of 55CrMo Steel during Induction Hardening

Huiping Li, Weilu Zhou, Haijuan Liu, Zhichao Li, Lianfang He

Journal of Testing and Evaluation· Volume 49· Issue 1
Publisher page

Abstract

Abstract To optimize the parameters of induction hardening and improve the surface hardness distribution of ball screw, the effects of the induction heating temperature on the microstructure and mechanical properties of 55CrMo steel were investigated. The specimens were heated up to 800°C, 850°C, 900°C, 950°C, 1,000°C, or 1,100°C by the induction heating power supply. Microstructural characterization of specimens was performed using an optical microscope and a high-resolution scanning electron microscope. The volume fraction of the retained austenite was measured using an X-ray diffractometer. The mechanical properties were evaluated by a microhardness tester and an electronic universal testing machine. The results show that the volume fraction of martensite in the hardened specimen increases with the increasing of heating temperature. A mixed microstructure consisting of ferrite + pearlite, bainite, and martensite is produced because of the nonfully and nonuniform austenitic state of original microstructure as the heating temperature is at 800°C. A full martensite can be produced as the heating temperature is more than 850°C. The volume fraction of retained austenite in the hardened specimen is lower when the heating temperature is in the range of 850°C–950°C; nonetheless, the volume fraction of retained austenite increases, and the tensile strength of the specimen reduces with the increasing of the heating temperature when the heating temperature is more than 950°C. The 55CrMo steel has good microstructure and mechanical properties and can meet the requirements of ball screw when the induction heating temperature is in the range of 850°C–950°C.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties · Metallurgy and Material Forming

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

School of Materials Science and Engineering, Shandong University of Science and Technology 1 , 579 Qianwangang Rd., Huangdao, Qingdao, Shandong 266510 ,

School of Materials Science and Engineering, Shandong University of Science and Technology 2 , 579 Qianwangang Rd., Huangdao, Qingdao, Shandong 266510 ,

School of Materials Science and Engineering, Shandong University of Science and Technology 3 , 579 Qianwangang Rd., Huangdao, Qingdao, Shandong 266510 ,

References (34)

Show source-provided references
1. Control of Surface Hardnesses, Hardening Depths, and Residual Stresses of Low Carbon 12Cr Steel by Flame Hardening10.1016/j.surfcoat.2003.10.063 ↗
2. Effect of Shot Peening on the Microstructure of Laser Hardened 17-4PH10.1016/j.apsusc.2010.07.015 ↗
3. The Effects of Induction Hardening on Wear Properties of AISI 4140 Steel in Dry Sliding Conditions10.1016/S0261-3069(02)00099-7 ↗
4. Experimental Determination of Process Parameters and Material Data for Numerical Modeling of Induction Hardening10.1007/s11665-013-0566-3 ↗
5. Numerical Simulation and Experimental Investigation on the Induction Hardening of a Ball Screw10.1016/j.matdes.2015.08.094 ↗
6. Induction Heating and Cryogenic Cooling in Single Point Incremental Forming of Ti-6Al-4V: Process Setup and Evolution of Microstructure and Mechanical Properties10.1007/s00170-016-9794-7 ↗
7. Microstructures and Mechanical Performance of Induction-Hardened Medium-Carbon Steels10.1016/B978-0-08-096532-1.01218-8 ↗
8. Effects of Induction Hardening and Prior Cold Work on a Microalloyed Medium Carbon Steel10.1361/105994999770346684 ↗
9. Failure Analysis of Forged and Induction Hardened Steel Cold Work Rolls10.1016/j.engfailanal.2003.11.005 ↗
10. Microstructural Evolution and Mechanical Properties of Low Alloy Steel Tempered by Induction Heating10.1016/j.jmatprotec.2004.03.019 ↗
11. Experimental Investigation on the Mechanical Behavior of High-Frequency Induction-Hardened Mild Carbon, SPS5 Steel10.1016/j.msea.2007.07.088 ↗
12. Influence of Process Parameters for Induction Hardening on Residual Stresses10.1016/S0261-3069(01)00033-4 ↗
13. Mathematical Model of Influence of Rapid Induction Heating on Nucleation and Growth of Precipitates10.1179/026708301101509278 ↗
14. Induction Hardening 5150 Steel: Effects of Initial Microstructure and Heating Rate10.1007/s11665-010-9825-8 ↗
15. Characterisation of Microstructure and its Effect on Rolling Contact Fatigue of Induction Hardened Medium Carbon Bearing Steels10.1179/mst.1998.14.8.816 ↗
16. Quality Control of Surface Inductive Quenching for Ball Screw (in Chinese)10.13251/j.issn.0254-6051.2011.01.017 ↗
17. Review on Grinding-Induced Residual Stresses in Metallic Materials10.1007/s00170-016-8998-1 ↗
18. Quality Analysis of GCr15 Steel Ball Screw After Quenched by Tilted Inductor (in Chinese)10.19382/j.cnki.1673-4971.2014.01.005 ↗
19. Wear Behaviour of Forging Steels with Different Microstructure during Dry Sliding10.1016/j.triboint.2007.09.002 ↗
20. Rolling Contact and Adhesive Wear of Bainitic and Pearlitic Steels in Low Load Regime10.1016/j.wear.2010.10.009 ↗
21. Role of Austenitization and Pre-Deformation on the Kinetics of the Isothermal Bainitic Transformation10.1007/s11661-009-9827-z ↗
22. Non-Isothermal Phase-Transformation Kinetics Model for Evaluating the Austenization of 55CrMo Steel Based on Johnson–Mehl–Avrami Equation10.1016/j.matdes.2015.12.110 ↗
23. Development of Rapid Heating and Cooling (Flash Processing) Process to Produce Advanced High Strength Steel Microstructures10.1179/174328409X433813 ↗
24. Effects of Hot Deformation and Subsequent Austempering on the Mechanical Properties of Si-Mn TRIP Steels10.2355/isijinternational.46.121 ↗
25. Modification of Rule of Mixtures for Estimation of the Mechanical Properties of Dual-Phase Steels10.1007/s11665-017-2687-6 ↗
26. Effects of Austenitization and Cooling Rates on the Microstructure in a Hyper-Eutectoid Steel10.3724/SP.J.1037.2012.00699 ↗
27. The Effect of Primary Thermo-Mechanical Treatment on TRIP Steel Microstructure and Mechanical Properties10.1016/j.msea.2015.05.045 ↗
28. The TRIP Effect and its Application in Cold Formable Sheet Steels10.1002/srin.201700218 ↗
29. Induction Hardening: Differences to a Conventional Heat Treatment Process and Optimization of its Parameters10.1088/1757-899X/119/1/012019 ↗
30. Tensile and Impact Behaviour of a Microalloyed Medium Carbon Steel: Effect of the Cooling Condition and Corresponding Microstructure10.1016/j.matdes.2012.08.063 ↗
31. Microstructure and Mechanical Properties of V–Ti–N Microalloyed Steel Used for Fracture Splitting Connecting Rod10.1007/s10853-010-5002-6 ↗
32. Effect of Cooling Rate on the Microstructure and Mechanical Properties of Microalloyed Forging Steel10.1016/j.jmatprotec.2007.12.006 ↗
33. Effect of Tempering on Microstructure and Mechanical Properties of Boron Containing 10%Cr Steel10.2355/isijinternational.51.1912 ↗
34. Influence of P-RE Compound Modification on Microstructure, Properties and Fracture Morphology of Hypereutectic Al-20Si Alloy10.3870/tzzz.2011.11.003 ↗