journal article·2019-07-01

Evaluation of ASTM D5764 Dowel Connection Tests for Laminated Veneer Bamboo (LVB)

N. Khoshbakht, P. L. Clouston, S. R. Arwade, A. C. Schreyer

Journal of Testing and Evaluation· Volume 47· Issue 4
Publisher page

Abstract

Abstract The ASTM D5764 standard, Standard Test Method for Evaluating Dowel-Bearing Strength of Wood and Wood-Based Products, for testing dowel connections provides a procedure for measuring the dowel bearing strength of wood and wood-based products. Laminated veneer bamboo (LVB) is a new building product that is employed in similar sizes and applications as dimensional lumber. Being new, more research is needed to understand the key factors and fundamental failure mechanisms that occur in LVB dowel connections to help ensure safe standards for further LVB product adoption and design. This study develops three-dimensional bilinear finite element models for half- and full-hole specimens in accordance with ASTM D5764 when loaded in compression parallel to the grain. The models simulate LVB fracture initiation due to shear stresses in the dowel joint by incorporating frictional stresses in the contact region between a steel bolt and LVB. The model also predicts displacement at failure, which is validated through comparison with experimental results: the material fails at 1 and 1.18 mm displacement loading parallel to the grain for half- and full-hole specimens, respectively. It is found that, despite the higher load-bearing capacity (strength) of the half-hole specimen, both specimens fail at approximately the same displacement because of in-plane shear stresses. This article clarifies the complex interactive state of in-plane shear, tension perpendicular to the grain, and compression parallel-to-grain stresses using the Tsai–Wu failure criterion in the critical zone beneath the bolt hole for half- and full-hole specimens. These findings suggest that care should be taken to select a test method that captures the performance of LVB dowel joints because of different failure mechanisms that occur for full- and half-hole specimens.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Bamboo properties and applications · Natural Fiber Reinforced Composites · Wood Treatment and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Department of Environmental Conservation, University of Massachusetts Amherst 1 , 551 N. Pleasant St., Amherst, MA 01003-2901 ,

Department of Environmental Conservation, University of Massachusetts Amherst 2 , 551 N. Pleasant St., Amherst, MA 01003-9293 ,

Department of Civil and Environmental Engineering, University of Massachusetts Amherst 3 , 130 Natural Resources Rd., Amherst, MA 01003 ,

References (18)

Show source-provided references
1. 2017
2. Dowelled Structural Connections in Laminated Bamboo and Timber10.1016/j.compositesb.2015.11.045 ↗
3. Computational Modeling of Laminated Veneer Bamboo Dowel Connections10.1061/(ASCE)MT.1943-5533.0002135 ↗
4. A Comparison between the EN 383 and ASTM D5764 Test Methods for Dowel-Bearing Strength Assessment of Wood: Experimental and Numerical Investigations10.1111/j.1475-1305.2008.00570.x ↗
5. 2007
6. 2018
7. Discussion of Testing and Evaluation Methods for the Embedment Behaviour of Connections
8. P. D. Rodd, “The Analysis of Timber Joints Made with Circular Dowel Connectors” (PhD thesis, University of Sussex, 1973).
9. Double Shear Timber Connections with Dowel Type Fasteners
10. An Experimental and Numerical Study of the Effect of Friction in Single Dowel Joints10.1007/s00107-008-0267-z ↗
11. 2009
12. 1998
13. 2015
14. 2015
15. Mechanical Characterization of Single Bamboo Fibers with Nanoindentation and Microtensile Technique10.1515/hf.2011.009 ↗
16. Effects of Humidity on Shear Behavior of Bamboo10.1016/j.taml.2015.11.007 ↗
17. Mechanical Properties of Wood
18. Failure Analysis of Typical Glubam with Bidirectional Fibers by Off-Axis Tension Tests10.1016/j.conbuildmat.2014.02.014 ↗