Effect of Pin Speed on Cerchar Abrasion Test Results
Source abstract
Abstract
Abstract Abrasive properties of rocks affect tool selection and design of rock excavation machines as well as their productivity and operational costs. The Cerchar test is a simple and commonly used method of measuring rock abrasion. The current article focuses on the effect of pin sliding speed on the Cerchar abrasion index. For this study, Cerchar tests were conducted on seven mono-mineral rock samples with different pin speeds. The results showed that the variation of pin speed could affect the wear of the pin tip. However, the effect is not uniform and depends on the hardness of rocks and pins. The changes in the pin speed can change the pin penetration into the sample surface as well. Harder pins penetrate deeper into the sample surface. However, the difference between harder and softer pins decreases with an increase in pin speed. Pin tip penetration into the sample surface is not changed by its sliding speed in hard samples such as quartz. Accordingly, a new parameter was introduced: the ratio of the volume of rock removed by scratch to the volume of pin tip wear. This ratio is called scratch volume to wear ratio (SVWR) and is used to determine the optimum pin motion speed in various conditions. The optimum pin speed could also be used as a guide to determine the optimum speed of cutting tools on rock surfaces in practical conditions. A new abrasion classification system was introduced based on SVWR and showed that it could be used regardless of pin hardness.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Tunneling and Rock Mechanics · Advanced materials and composites · Metal Alloys Wear and Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Mining Engineering Faculty, Sahand University of Technology 1 , Sahand New Town, Tabriz 5331811111 ,
Mining Engineering Faculty, Sahand University of Technology 2 , Sahand New Town, Tabriz 5331811111 ,
Department of Mining Engineering, Colorado School of Mines 3 , 1500 Illinois St, Golden, CO 80401-1887 ,
References (47)
Show source-provided references
1. Wear of the Cutting Tools of Rock Excavation Machines
2. DIN 50320 · 1979
3. 1997 · 327
4. New Test Methodology for Estimating the Abrasiveness of Soils for TBM Tunneling
5. CERCHAR, “Cerchar Tests for the Measurement of Hardness and Abrasivity of Rocks,” Document 73-59, Laboratoire du Centre d’Études et Recherches des Charbonnages de France, Verneuil, France, 1973, pp. 1–10.
6. NF P 94-430-1 · 2000
7. ASTM D7625-10 · 2010
8. ISRM Suggested Method for Determining the Abrasivity of Rock by the CERCHAR Abrasivity Test10.1007/s00603-013-0518-0 ↗
9. CAI Testing and Its Implications
10. The Cerchar Abrasiveness Index
11. 2000 · 658
12. Wear Prediction in Hard Rock Excavation Using the Cerchar Abrasiveness Index (CAI)
13. A Study of Rock Abrasivity and Tool Wear in Coal Measures Rocks10.1016/j.coal.2007.09.007 ↗
14. Prediction of Cutter Wear Using RME
15. Study of Dominant Factors Affecting Cerchar Abrasivity Index10.1007/s00603-013-0487-3 ↗
16. The Cerchar Abrasivity Index and Its Relation to Rock Mineralogy and Petrography10.1007/BF01239473 ↗
17. Rock Abrasiveness Testing for Tunneling10.1016/0148-9062(89)90003-X ↗
18. The Influence of Rock Strength and Abrasive Mineral Content on the Cerchar Abrasive Index10.1016/0013-7952(94)90010-8 ↗
19. Testing Conditions and Geomechanical Properties Influencing the Cerchar Abrasivity Index (CAI) Value10.1016/S1365-1609(02)00140-5 ↗
20. Study on the Correlations between Abrasiveness and Mechanical Properties of Rocks Combining with the Microstructure Characteristic10.1007/s00603-015-0862-3 ↗
21. The Usability of Cerchar Abrasivity Index for the Prediction of UCS and E of Misis Fault Breccia: Regression and Artificial Neural Network Analysis10.1016/j.eswa.2010.06.039 ↗
22. Correlating Index Properties of Rocks with P-Wave Measurements10.1016/j.jappgeo.2010.01.007 ↗
23. Cerchar Abrasivity Index (CAI) and Its Relation to Strength and Abrasion Test Methods for Marble Stones10.1016/j.conbuildmat.2011.11.023 ↗
24. Prediction of Abrasiveness Index of Some Indian Rocks Using Soft Computing Methods10.1016/j.measurement.2015.03.009 ↗
25. Strength Properties and Their Relations with Abrasiveness of Some India Rocks
26. Jager, W., “An Investigation into the Abrasive Capacity of Rocks,” Ph.D. dissertation, Delft University of Technology, Delft, the Netherlands, 1988.
27. Reinking, M. W., “Linear Cutting Tests in Artificial Sand-Clay Mixtures to Study the Influence of Brittleness on Abrasive Wear of Cutting Tools,” Ph.D. dissertation, Delft University of Technology, Delft, the Netherlands, 1989.
28. Stress Dependency of the Cerchar Abrasivity Index (CAI) and Its Effects on Wear of Selected Rock Cutting Tools10.1016/j.tust.2007.05.008 ↗
29. Rock Abrasivity—A Significant Cost Factor for Mechanical Tunnelling in Loose and Hard Rock
30. The Influence of Steel Styli Hardness on the Cerchar Abrasiveness Index Value10.1016/j.ijrmms.2005.06.009 ↗
31. Statistical Evaluation of CERCHAR Abrasivity Index (CAI) Measurement Methods and Dependence on Petrographic and Mechanical Properties of Selected Rocks of Pakistan10.1007/s10064-015-0799-5 ↗
32. Continuous Monitoring of Pin Tip Wear and Penetration into Rock Surface Using a New Cerchar Abrasivity Testing Device10.1007/s00603-013-0397-4 ↗
33. Study of Rock-Pin Interaction in Cerchar Abrasivity Test10.1016/j.ijrmms.2014.09.007 ↗
34. The Influence of Speed on Metallic Wear10.1098/rspa.1960.0220 ↗
35. The Dry Wear of Steels: I. The General Pattern of Behavior
36. Wear of Metals at High Sliding Speeds10.1016/0043-1648(77)90089-8 ↗
37. Effects of Sliding Speed on the Unlubricated Wear Behavior of Al-12.3wt.%Si Alloy10.1016/0043-1648(91)90349-Y ↗
38. On Wear Characteristics of Leaded Aluminum-Silicon Alloys10.1016/0043-1648(94)90116-3 ↗
39. The Mechanisms of Oxidational Wear10.1016/0043-1648(94)06569-1 ↗
40. Dry Sliding Wear Mechanisms of the Ti6Al4V Alloy10.1016/S0043-1648(96)07454-6 ↗
41. High-Speed Tribological Properties of Some Al/SiCp Composites: I. Frictional and Wear-Rate Characteristics10.1016/S0266-3538(98)00055-4 ↗
42. Wear Behavior of Cast Hypereutectic Aluminum Silicon Alloys10.1016/j.matdes.2004.11.029 ↗
43. Influence of Sliding Speed on the Dry Sliding Wear Behavior and the Subsurface Deformation on Hybrid Metal Matrix Composite10.1016/j.wear.2006.10.016 ↗
44. Wear and Friction of Al-Al2O3 Composites at Various Sliding Speeds10.1007/s10853-008-2867-8 ↗
45. Wear Behavior of AZ91D Alloy at Low Sliding Speeds10.1016/j.wear.2008.01.012 ↗
46. Dry Sliding Wear Behavior of Aluminum Matrix Composite Using Red Mud an Industrial Waste10.9734/IRJPAC/2013/2906 ↗
47. Dry Sliding Wear Behavior of AM50B Magnesium Alloy10.1016/j.matdes.2013.12.015 ↗