journal article·2014-04

Characterization of network parameters for UHMWPE by plane strain compression

E.L. Abreu, H.D. Ngo, A. Bellare

Publisher page

Abstract

Ultra-high molecular weight polyethylene (PE) is used as a bearing material for total joint replacement prostheses since it is a tough, wear-resistant semicrystalline polymer. Despite its high resistance to wear, PE components have shown measureable wear in vivo, which can cause wear-particle induced osteolysis. Crosslinking of PE using ionizing radiation has been shown to increase wear resistance since both chemical crosslinks and physical entanglements provide high resistance to wear. Molecular characterization of crosslinked PEs is usually conducted using equilibrium swelling or by quantifying gel content. In this study, we compared crosslink densities and molecular weight between crosslinks derived from equilibrium swelling to those obtained by applying the Gaussian and Eight-Chain model to describe plane strain compression of the PE melt. The latter approach has the advantage of accounting for contributions of entanglements to the overall crosslink density, which solvent-based techniques largely neglect. As expected, the crosslink density calculated from model fitting increased monotonically with increase in radiation dose in a 0-200kGy dose range, with a corresponding monotonic decrease in molecular weight between crosslinks, but provided higher values of crosslink density and correspondingly lower values of molecular weight between crosslinks compared to the equilibrium swelling technique.
Source: europepmc · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Orthopaedic implants and arthroplasty · Total Knee Arthroplasty Outcomes · Polymer crystallization and properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (33)

Show source-provided references
1. ASTM standard D2765-11. Standard Test Methods for Determination of Gel Content and Swell Ratio of Crosslinked Ethylene Plastics: 1–7.
2. ASTM standard F 2214-02. Standard Method for In Situ Determination of Network Parameters of Crosslinked Ultra-High Molecular Weight Polyethylene (UHMWPE): 1–5.
3. ASTM standard F 2214-02. Standard Method for In Situ Determination of Network Parameters of Crosslinked Ultra-High Molecular Weight Polyethylene (UHMWPE) 2008: 1–5.
4. A 3-dimensional constitutive model for the large stretch behavior of rubber elastic-materials10.1016/0022-5096(93)90013-6 ↗
5. The effects of degree of crosslinking on the fatigue crack initiation and propagation resistance of orthopedic-grade polyethylene10.1002/jbm.a.10606 ↗
6. Effect of chain entanglements on plastic deformation behavior of linear polyethylene10.1021/ma050815y ↗
7. Constitutive modeling of ultra-high molecular weight polyethylene under large-deformation and cyclic loading conditions10.1016/S0142-9612(01)00367-2 ↗
8. Prediction of multiaxial mechanical behavior for conventional and highly crosslinked UHMWPE using a hybrid constitutive model10.1016/S0142-9612(02)00514-8 ↗
9. Pade approximant to the inverse Langevin function10.1007/BF00366640 ↗
10. Molecular deformation mechanisms in UHMWPE during tribological loading in artificial joints10.1007/s11249-009-9563-y ↗
11. Update on UHMWPE research: from the bench to the bedside10.1080/17453670810016939 ↗
12. J-integral fracture toughness and tearing modulus measurement of radiation cross-linked UHMWPE10.1016/S0736-0266(02)00073-6 ↗
13. The radiation improvement of polyethylene prostheses: a preliminary study10.1302/0301-620X.60B3.681412 ↗
14. The effects of peroxide content on the wear behavior, microstructure and mechanical properties of peroxide crosslinked ultra-high molecular weight polyethylene used in total hip replacement10.1007/s10856-008-3368-7 ↗
15. The problem is osteolysis
16. Strain-Hardening of Thermoplastics10.1021/ma00074a006 ↗
17. Advances in the processing, sterilization, and crosslinking of ultra-high molecular weight polyethylene for total joint arthroplasty10.1016/S0142-9612(99)00053-8 ↗
18. History and systematic review of wear and osteolysis outcomes for first-generation highly crosslinked polyethylene10.1007/s11999-011-1872-4 ↗
19. Formation of entanglements in initially disentangled polymer melts10.1021/ma062284z ↗
20. Development of an extremely wear-resistant ultra high molecular weight polyethylene for total hip replacements10.1002/jor.1100170203 ↗
21. The origin of submicron polyethylene wear debris in total hip arthroplasty
22. Comparative fatigue behavior and toughness of remelted and annealed highly crosslinked polyethylenes10.1002/jbm.b.30807 ↗
23. Unified wear model for highly crosslinked ultra-high molecular weight polyethylenes (UHMWPE)10.1016/S0142-9612(99)00039-3 ↗
24. Unified wear model for highly crosslinked ultra-high molecular weight polyethylenes (UHMWPE)10.1016/S0142-9612(99)00039-3 ↗
25. Ex vivo stability loss of irradiated and melted ultra-high molecular weight polyethylene10.2106/JBJS.I.01017 ↗
26. Effect of cross-linkage by gamma radiation in heavy doses to low wear polyethylene in total hip prostheses
27. Mechanisms of decrease in fatigue crack propagation resistance in irradiated and melted UHMWPE10.1016/j.biomaterials.2005.06.025 ↗
28. Viscosity and self-diffusion coefficient of hydrogenated polybutadiene10.1021/ma00081a014 ↗
29. The combined effects of crosslinking and high crystallinity on the microstructural and mechanical properties of ultra high molecular weight polyethylene10.1016/j.biomaterials.2005.09.033 ↗
30. Raman tensor analysis of ultra-high molecular weight polyethylene and its application to study retrieved hip joint components10.1016/j.actbio.2010.02.051 ↗
31. Innovative materials in orthopaedics: the crosslinked polyethylene (XPE)
32. Mechanistic and morphological origins of ultra-high molecular weight polyethylene wear debris in total joint replacement prostheses10.1243/PIME_PROC_1996_210_407_02 ↗
33. 1995