journal article·2021-07Open access

Erosion of CAD/CAM restorative materials and human enamel: An in vitro study

Hui Yang, Zhi-cen Lu, Thomas Attin, Hao Yu

Abstract

This in vitro study used the same frequency and duration of acid contact as a previous in situ/in vivo study to evaluate the effect of erosion on CAD/CAM restorative materials and human enamel and to compare the effects of in vitro and in situ/in vivo acid challenges on CAD/CAM restorative materials and human enamel. The CAD/CAM restorative materials (IPS e.max CAD, Lava Ultimate, and PMMA block) and human enamel were eroded by immersion in 150 ml of cola drink for 14 days (4 × 5 min/day). The surface microhardness and surface roughness of the specimens were measured at baseline (T1), day 7 (T2), and day 14 (T3). The substance losses were measured at T2 and T3. The data were statistically analyzed using repeated measures ANOVA and Bonferroni's test (α = 0.05). Erosion significantly decreased the surface microhardness of the CAD/CAM restorative materials and human enamel (all P < 0.001). The overall percentage of surface microhardness loss (%SMH l ) of the PMMA block and enamel due to in vitro erosion was significantly higher than that due to in situ/in vivo erosion (P = 0.02 and P < 0.001, respectively). Consistent with in situ/in vivo erosion, the surface roughness and profile of the tested restorative materials remained unchanged after in vitro erosion. A significant increase in the surface roughness and substance loss was observed for enamel after in vitro erosion (all P < 0.001). The overall substance loss of enamel due to in vitro erosion was significantly higher than that due to in situ/in vivo erosion (P < 0.001). In conclusion, erosion decreased the surface microhardness of the CAD/CAM restorative materials and human enamel. Moreover, erosion negatively influenced the substance loss and surface roughness of human enamel. For the substance loss of enamel and %SMH l of PMMA block and enamel, the in vitro erosive effects were approximately 1–2 times greater than the in situ/in vivo effects. However, for the surface roughness and profile of the CAD/CAM restorative materials, no significant difference was found between in vitro and in situ/in vivo erosion.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Dental Erosion and Treatment · Dental materials and restorations · Temporomandibular Joint Disorders

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (30)

Show source-provided references
1. Effect of beverage solutions and toothbrushing on the surface roughness, microhardness, and color stainability of a vitreous CAD-CAM lithium disilicate ceramic10.1016/j.prosdent.2019.02.001 ↗
2. Effect of acidic pH on surface roughness of esthetic dental materials10.1016/j.prosdent.2019.08.022 ↗
3. Effect of storage in artificial saliva and thermal cycling on Knoop hardness of resin denture teeth10.1016/j.jpor.2009.12.001 ↗
4. Effect of mineral supplements to citric acid on enamel erosion10.1016/S0003-9969(03)00156-0 ↗
5. Impact of erosive conditions on tooth-colored restorative materials10.1016/j.dental.2013.07.017 ↗
6. Vickers micro-hardness of new restorative CAD/CAM dental materials: evaluation and comparison after exposure to acidic drink10.3390/ma12081246 ↗
7. Influence of simulated gastric juice on surface characteristics of CAD-CAM monolithic materials10.1016/j.prosdent.2019.04.018 ↗
8. Effects of different pH-values on the nanomechanical surface properties of PEEK and CFR-PEEK compared to dental resin-based materials10.3390/ma8084751 ↗
9. Knowledge of and attitudes towards erosive tooth wear among students of two Chinese universities10.1186/s12903-020-01105-7 ↗
10. The protective effects of toothpaste against erosion by orange juice: studies in situ and in vitro10.1016/j.jdent.2007.01.003 ↗
11. Development and evaluation of a low erosive blackcurrant juice drink in vitro and in situ. 1. Comparison with orange juice10.1016/S0300-5712(98)00069-4 ↗
12. Prevalence, incidence and distribution of erosion10.1159/000360973 ↗
13. Effect of acidic agents on surface roughness of dental ceramics
14. Quantitative in vivo wear of human enamel10.1177/00220345890680120601 ↗
15. Dental erosion--an overview with emphasis on chemical and histopathological aspects10.1159/000325915 ↗
16. Investigation of the influence of gastric acid on the surface roughness of ceramic materials of metal-ceramic restorations. An in vitro study
17. An in-situ pilot study to investigate the native clinical resistance of enamel to erosion10.1016/j.jdent.2018.01.005 ↗
18. Comparison of methods for quantifying dental wear caused by erosion and abrasion10.1002/jemt.22150 ↗
19. In situ effect of an erosive challenge on different restorative materials and on enamel adjacent to these materials10.1016/j.jdent.2007.11.013 ↗
20. Chemical degradation of dental CAD/CAM materials
21. Is dental erosion really a problem?10.1177/0022034512449836 ↗
22. Impact of gastric acidic challenge on surface topography and optical properties of monolithic zirconia10.1016/j.dental.2015.09.010 ↗
23. In vitro and in situ erosion models for evaluating tooth substance loss10.1159/000325945 ↗
24. A method to measure clinical erosion: the effect of orange juice consumption on erosion of enamel10.1016/S0300-5712(97)00025-0 ↗
25. Enamel wear by antagonistic restorative materials under erosive conditions10.1007/s00784-017-2071-9 ↗
26. Repolishing in situ eroded CAD/CAM restorative materials and human enamel10.1016/j.jmbbm.2020.104125 ↗
27. Erosion of CAD/CAM restorative materials and human enamel: an in situ/in vivo study10.1016/j.jmbbm.2020.103903 ↗
28. In situ effect of Tooth Mousse containing CPP-ACP on human enamel subjected to in vivo acid attacks10.1016/j.jdent.2018.05.021 ↗
29. Erosion and abrasion of tooth-colored restorative materials and human enamel10.1016/j.jdent.2009.07.006 ↗
30. Effect of acidic agents on the wear behavior of a polymer infiltrated ceramic network (PICN) material10.1016/j.jmbbm.2017.06.001 ↗