journal article·2021-12

Fabrication and characterization of a semi-rigid shell barrier system made of polycaprolactone and biphasic calcium phosphate: A novel barrier system for bone regeneration

Rudjit Tunthasen, Prisana Pripatnanont, Jirut Meesane

Publisher page

Abstract

Introduction Nowadays, no barrier membrane serves all purposes of bone augmentation. This study aimed to fabricate a semi-rigid shell barrier system composed of a semi-rigid shell and a covering membrane or a semi-resorbable barrier membrane, based on polycaprolactone (PCL) and biphasic calcium phosphate (BCP) for guided bone regeneration (GBR). Materials and methods A shell and a covering membrane were fabricated by a solvent casting technique based on PCL (70) and BCP (30). The experimental groups were a semi-rigid shell, an airdried membrane, a buffered membrane, and a commercial d-PTFE as a control. Physico-chemical, mechanical properties, and in vitro biocompatibility with osteoblasts and fibroblasts cells were evaluated in all groups. Results The fabricated materials had rough surfaces with a homogeneous distribution of BCP particles on one side and a smooth surface on the opposite side. The airdried membrane presented a rougher surface on both top and bottom sides (Sq = 605.45 nm, 556.82 nm) than the semi-rigid shell (310.74 nm, 424.56 nm) and the buffered membrane (277.9 nm, 306.98 nm), respectively. The pore sizes of the airdried membrane (25-40 μm) were larger than the semi-rigid shell (5-40 μm) and the buffered membrane (5-25 μm). The porosities of the airdried and buffered membranes (∼40%) were higher than the semi-rigid shell (∼20%) significantly (p < 0.05). All fabricated materials were hydrophilic, with the lowest water contact angle in the semi-rigid shell (54.7° ± 3.06°), then the airdried (61.15° ± 4.76°), and the buffered (75.74° ± 2.8°) respectively. The semi-rigid shell resisted a higher load on compressive force (18.82 ± 2.72 N) than the d-PTFE membrane (4.23 ± 0.5 N). The tensile stress of the buffered membrane (2.544 ± 0.19 MPa) was not different from the d-PTFE (2.908 ± 0.12 MPa) but was higher than the airdried membrane (1.302 ± 0.13 MPa) significantly (P < 0.05). The airdried membrane had reached 100% swelling ability within 1 h, which was significantly faster than the buffered membrane (12 h) and the semi-rigid shell (7 days), and they were slowly degraded by lysozyme at 6 months (airdried: 24.88% ± 0.96%, buffered: 13.67% ± 0.55%, and semi-rigid: 8.62% ± 0.88%). All fabricated membranes showed no toxicity to osteoblast and fibroblast cells. Conclusion The semi-rigid shell and the covering membranes demonstrated suitable physical and mechanical properties, and biocompatibility, and can be assembled as the novel semi-rigid shell barrier system for bone regeneration.
Source: europepmc · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Bone Tissue Engineering Materials · Periodontal Regeneration and Treatments · Dental Implant Techniques and Outcomes

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (29)

Show source-provided references
1. A novel bilayer polycaprolactone membrane for guided bone regeneration: combining electrospinning and emulsion templating10.3390/ma12162643 ↗
2. Use of a new cross-linked collagen membrane for the treatment of peri-implant dehiscence defects: a randomised controlled double-blinded clinical trial
3. Biocompatibility evaluation of orthopedic biomaterials and medical devices: a review of safety and efficacy models
4. The use of e-PTFE barrier membranes for bone promotion around titanium implants placed into extraction sockets: a prospective multicenter study
5. Research of calcium phosphates using fourier transform infrared spectroscopy
6. The role of pore size on vascularization and tissue remodeling in PEG hydrogels10.1016/j.biomaterials.2011.04.066 ↗
7. Fabrication and characterization of novel nano hydroxyapatite/beta-tricalcium phosphate scaffolds in three different composition ratios10.1002/jbm.a.34160 ↗
8. In vitro biocompatibility analysis of novel nano-biphasic calcium phosphate scaffolds in different composition ratios10.1002/jbm.b.32979 ↗
9. FTIR study of polycaprolactone chain organization at interfaces10.1016/j.jcis.2004.02.001 ↗
10. Physicomechanical properties of degradable polymers used in medical applications: a comparative study
11. On the structural, mechanical, and biodegradation properties of HA/beta-TCP robocast scaffolds10.1002/jbm.b.32935 ↗
12. Impact of pore size on the vascularization and osseointegration of ceramic bone substitutes in vivo10.1002/jbm.a.31559 ↗
13. Synthesis and characterization of polycaprolactone-based polyurethanes for the fabrication of elastic guided bone regeneration membrane
14. Mechanisms of guided bone regeneration: a review10.2174/1874210601408010056 ↗
15. Mechanical properties of trabecular bone in the human mandible: implications for dental implant treatment planning and surgical placement10.1016/S0278-2391(99)90437-8 ↗
16. Biodegradable polymers as biomaterials10.1016/j.progpolymsci.2007.05.017 ↗
17. 7 - characterization of biomaterials
18. Mechanical qualification of collagen membranes used in dentistry
19. Bone regeneration potential of biphasic nanocalcium phosphate with high hydroxyapatite/tricalcium phosphate ratios in rabbit calvarial defects10.11607/jomi.4531 ↗
20. Preparation and characterization of poly (ε- caprolactone)/Tio2 micro-composites
21. Swelling effects in cross-linked polymers by thermogravimetry10.1007/s10973-017-6131-9 ↗
22. A comparative study of the effectiveness of e-PTFE membranes with and without early exposure during the healing period
23. 2D and 3D pore structure characterization of bi-layered porous polyethylene barrier membrane using SEM and micro-CT10.2306/scienceasia1513-1874.2019.45.159 ↗
24. Contact angle measurement for the surface characterization of solids10.3126/hj.v2i2.5201 ↗
25. Biphasic calcium phosphate in periapical surgery10.4103/0972-0707.44059 ↗
26. Physical characteristics and biocompatibility of the polycaprolactone-biphasic calcium phosphate scaffolds fabricated using the modified melt stretching and multilayer deposition10.1177/0885328216633890 ↗
27. Biomechanical properties of novel biodegradable poly epsilon-caprolactone-chitosan scaffolds10.1111/j.2041-1626.2012.00131.x ↗
28. Biodegradable polymer membranes applied in guided bone/tissue regeneration: a review10.3390/polym8040115 ↗
29. Fabrication aspects of PLA-CaP/PLGA-CaP composites for orthopedic applications: a review10.1016/j.actbio.2012.01.031 ↗