journal article·2023-06

Adhesion to lithium disilicate glass-ceramics after aging: Resin viscosity and ceramic surface treatment effects

Kiara Serafini Dapieve, Rafaela Oliveira Pilecco, Renatta Wrasse Temp, Marcos Antonio Villetti, Gabriel Kalil Rocha Pereira, Luiz Felipe Valandro

Publisher page

Abstract

Objective To evaluate the influence of intaglio ceramic surface treatments, resin cement viscosities, and storage regimens on the microshear bond strength of lithium disilicate ceramic. In addition, to investigate the dynamic viscosity of the resin-based luting agents. Materials and methods Ceramic slices were randomly allocated into eight groups (n = 19) considering three factors: ceramic surface treatment (hydrofluoric acid followed by silane, HF; or self-etching ceramic primer, E&P), resin cement viscosity (high, HIGH; or low, LOW) and storage regimen (baseline or aging). Surface treatments were performed, resin cement cylinders were built and microshear bond strength tests (μSBS, wire-loop method, speed: 1.0 mm/min) were run according to the storage factor. Failure mode, topographic and dynamic viscosity (37 °C; shear rate of 1.0-100 s-1) of resin cement components (base, high and low catalyst) were also performed. Results Resin cement viscosity and the association among ceramic surface treatment, resin cement viscosity, and storage regimen were statistically significant factors (p < 0.05). Worse behavior was identified for the E&P_HIGH group compared to the E&P_LOW and HF_LOW in the baseline condition. After aging, the HF_HIGH group (16.78 MPa) presented the worst result among the aged groups (21.44-25.25 MPa). Most of the failures were adhesive. Surface micrographs revealed a distinct pattern after etching, more aggressive by HF and milder by E&P. High viscosity catalyst is 5.3 and 8.5-fold more viscous than the base and low viscosity catalyst, respectively (high > base > low). Conclusion Differences in filler content can impact the resin viscosity of the material (more fillers increase the viscosity), which in turn can influence the bond strength of a lithium disilicate ceramic, depending on the surface treatment and storage regimen.
Source: europepmc · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Dental materials and restorations · Recycling and utilization of industrial and municipal waste in materials production · Advanced ceramic materials synthesis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (33)

Show source-provided references
1. Exploring ductility in dental ceramics10.1177/00220345221100409 ↗
2. Academy of Dental Materials guidance on in vitro testing of dental composite bonding effectiveness to dentin/enamel using micro-tensile bond strength (μTBS) approach10.1016/j.dental.2016.11.015 ↗
3. Clinical outcomes of lithium disilicate glass-ceramic crowns fabricated with CAD/CAM technology: a systematic review10.17219/dmp/115522 ↗
4. Advances in ceramics for dental applications
5. A systematic review and meta-analysis on using preheated resin composites as luting agents for indirect restorations10.1007/s00784-022-04406-z ↗
6. Influence of inorganic filler content of resin luting agents and use of adhesive on the performance of bonded ceramic10.1016/j.prosdent.2019.09.013 ↗
7. Rheological properties of experimental Bis-GMA/TEGDMA flowable resin composites with various macrofiller/microfiller ratio10.1016/j.dental.2008.06.001 ↗
8. Response of composite resins to preheating and the resulting strengthening of luted feldspar ceramic10.1016/j.dental.2019.07.021 ↗
9. Does adhesive luting reinforce the mechanical properties of dental ceramics used as restorative materials? A systematic review and meta-analysis
10. Different etching times of a one-step ceramic primer: effect on the resin bond strength durability to a CAD/CAM lithium-disilicate glass-ceramic
11. Cyclic fatigue vs static loading for shear bond strength test of lithium disilicate and dentin substrates: a comparison of resin cement viscosities10.1016/j.dental.2022.09.008 ↗
12. Do resin cement viscosity and ceramic surface etching influence the fatigue performance of bonded lithium disilicate glass-ceramic crowns?10.1016/j.dental.2021.12.015 ↗
13. Dean · 2013
14. Self-Etch silane primer: reactivity and bonding with a lithium disilicate ceramic10.3390/ma13030641 ↗
15. Advanced statistics: bootstrapping confidence intervals for statistics with "difficult" distributions
16. 2021
17. Rheological properties of resin composites according to variations in monomer and filler composition10.1016/j.dental.2005.05.008 ↗
18. Effect of universal adhesives and self-etch ceramic primers on bond strength to glass ceramics: a systematic review and meta-analysis of in vitro studies
19. Viscosity and thermal kinetics of 10 preheated restorative resin composites and effect of ultrasound energy on film thickness10.1016/j.dental.2020.08.004 ↗
20. A review of adhesion science10.1016/j.dental.2009.11.157 ↗
21. Effect of milling, fitting adjustments, and hydrofluoric acid etching on the strength and roughness of CAD-CAM glass-ceramics: a systematic review and meta-analysis
22. Influence of accelerated ageing on the physical properties of CAD/CAM restorative materials10.1007/s00784-019-03101-w ↗
23. Surface milled by CAD-CAM system vs laboratorial methods to simulate the milled surface: effect on the resin bond strength to lithium disilicate glass-ceramic10.1016/j.ijadhadh.2021.103068 ↗
24. Ceramic surface treatment with a single-component primer: resin adhesion to glass ceramics
25. How does hydrofluoric acid etching affect the cyclic load-to-failure of lithium disilicate restorations?10.1016/j.jmbbm.2018.07.040 ↗
26. Adhesion to a lithium disilicate glass ceramic etched with hydrofluoric acid at distinct concentrations10.1590/0103-6440201802080 ↗
27. Hydrofluoric acid concentrations: effect on the cyclic load-to-failure of machined lithium disilicate restorations10.1016/j.dental.2018.06.028 ↗
28. Starch tubing: an alternative method to build up microshear bond test specimens
29. Self-etching primers vs acid conditioning: impact on bond strength between ceramics and resin cement10.2341/16-348-L ↗
30. Effect of active application of self-etching ceramic primer on the long-term bond strength of different dental CAD/CAM materials10.4317/jced.58723 ↗
31. How much do resin-based dental materials release? A meta-analytical approach10.1016/j.dental.2011.05.001 ↗
32. Editorial: the VALUE and remaining NEED of bond-strength testing
33. Wang · 2016 · 21