Effects of surface roughness on the time-dependent wear performance of lithium disilicate glass ceramic for dental applications
Source abstract
Abstract
Objectives Purpose of the present study was to evaluate the effect of surface roughness on the time-dependent wear performance of lithium disilicate (LD) glass-ceramic. Methods Friction pairs (pin and disk specimens) were prepared by IPS e.max® Press lithium disilicate glass-ceramic. The lateral faces of friction pairs (N = 12) were grinded with silicon carbide papers, and 6 friction pairs were polished with a 0.25 μm diamond suspension after grinding. The friction pairs were tested for wear performance using a pin-on-disk tribometer with 10 N for 1.02 × 106 wear cycles in artificial saliva. Wear analysis of the pin and disk was performed with a 3D profilometer. The microstructure and worn surface morphology were examined with scanning electron microscopy. One-way analysis of variance and Tukey's post-hoc pairwise comparison were used to analyze the wear data. Results The two group LD friction pairs presented strong time-dependent wear performance. The polished group (GP) exhibited a high wear rate and extensive surface wear during 0-1 × 105 cycles (running-in wear stage). The wear rate, height loss and surface roughness were obviously lower than those of grinded group (GG) in running-in wear stage. However, these wear parameters were similar during the steady wear stage. The worn surface topographies of the pin and disk in GP were smoother at the same cycle before the GG entering the steady wear stage. Conclusion Running-in, which means the initial stage of wear process, is a critical period to determine the final wear loss and surface degradation, when compare the wear behavior of lithium disilicate ceramic with different initial surface states. Ceramic layer with smooth contact area leads to low wear rate and short running-in wear stage.
Source: europepmc · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Dental materials and restorations · Advanced ceramic materials synthesis · Bone Tissue Engineering Materials
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (38)
Show source-provided references
1. Effect of simulated mastication on the surface roughness of three ceramic systems10.1016/j.prosdent.2015.02.018 ↗
2. Three-body wear potential of dental yttrium-stabilized zirconia ceramic after grinding, polishing, and glazing treatments10.1016/j.prosdent.2013.12.021 ↗
3. Damage sensitivity of dental zirconias to simulated occlusal contact10.1016/j.dental.2020.10.019 ↗
4. Surface roughness of packable composite resins polished with various systems10.1111/j.1708-8240.2004.tb00450.x ↗
5. The effect of surface treatment on the friction and wear behavior of dental Y-TZP ceramic against human enamel10.1016/j.triboint.2017.07.016 ↗
6. Effect of glazed and polished surface finishes on the friction coefficient of two low-fusing ceramics10.1016/j.prosdent.2004.12.010 ↗
7. Surface roughness and flexural strength of self-glazed, polished, and reglazed in-ceram/vitadur alpha porcelain laminates
8. Toughening of Li2O-2SiO2 glass-cramics induced by intriguing deformation behavior of lithium disilicate nanocrystal10.1111/jace.16794 ↗
9. Investigation of the time-dependent wear behavior of veneering ceramic in porcelain fused to metal crowns during chewing simulations10.1016/j.jmbbm.2014.08.006 ↗
10. Effect of microstructure on the mechanical properties of lithium disilicate glass-ceramics10.1016/j.jmbbm.2018.02.032 ↗
11. Wear of ceramic and antagoniste-a systematic evaluation of influencing factors in vitro10.1016/j.dental.2007.06.016 ↗
12. How to qualify and validate wear simulation devices and methods10.1016/j.dental.2006.02.002 ↗
13. The wear of polished and glazed zirconia against enamel10.1016/S0022-3913(13)60005-0 ↗
14. Ji · 2021 · 203845
15. The progressive wear and abrasiveness of novel graded glass/zirconia materials relative to their dental ceramic counterparts10.1016/j.dental.2019.02.022 ↗
16. A systematic methodology to characterise the running-in and steady-state wear processes10.1016/S0043-1648(01)00895-X ↗
17. Wear of enamel opposing zirconia and lithium disilicate after adjustment, polishing and glazing10.1016/j.jdent.2014.09.008 ↗
18. Influence of full-contour zirconia surface roughness on wear of glass-ceramics10.1111/jopr.12088 ↗
19. Wear: mechanisms, manifestations and measurement. Report of a workshop10.1016/0300-5712(95)00043-7 ↗
20. Improving the wear performance of feldspathic veneering porcelain by ion-exchange strengthening10.1016/j.jdent.2019.103210 ↗
21. Improved reliability of wear performance for a fluorapatite veneering porcelain by ion-exchange strengthening and toughening10.1016/j.jmbbm.2020.103986 ↗
22. Wear behaviour of dental Y-TZP ceramic against natural enamel after different finishing procedures10.1016/j.dental.2012.04.010 ↗
23. Invitro 2d and 3d roughness and spectrophotometric and gloss analyses of ceramic materials after polishing with different prophylactic pastes - sciencedirect10.1016/j.prosdent.2020.05.040 ↗
24. Factors affecting enamel and ceramic wear: a literature review10.1067/mpr.2002.123851 ↗
25. The effect of glazed and polished ceramics on human enamel wear
26. A fractographic study of clinically retrieved zirconia-ceramic and metal-ceramic fixed dental prostheses10.1016/j.dental.2015.07.003 ↗
27. Wear behavior of pressable lithium disilicate glass ceramic10.1002/jbm.b.33447 ↗
28. Wear performance of dental ceramics after grinding and polishing treatments10.1016/j.jmbbm.2012.03.002 ↗
29. Wear performance of substructure ceramics and veneering porcelains10.1016/j.dental.2011.04.001 ↗
30. Cycle-dependent in vitro wear performance of dental ceramics after clinical surface treatments10.1016/j.jmbbm.2015.08.009 ↗
31. Surface properties of monolithic zirconia after dental adjustment treatments and in vitro wear simulation10.1016/j.jdent.2014.08.011 ↗
32. Sliding contact fracture of dental ceramics: principles and validation10.1016/j.actbio.2014.03.004 ↗
33. Wear characteristics of polished and glazed lithium disilicate ceramics opposed to three ceramic materials10.2334/josnusd.58.117 ↗
34. Effect of bur selection on machining damage mechanisms of polymer-infiltrated ceramic network material for cad/cam dental restorations10.1016/j.ceramint.2020.06.089 ↗
35. Sliding contact wear and subsurface damage of CAD/CAM materials against zirconia10.1016/j.dental.2020.01.015 ↗
36. Comparison of three systems for the polishing of an ultra-low fusing dental porcelain10.1016/j.prosdent.2004.07.021 ↗
37. The effect of food medium on the wear behaviour of veneering porcelain: an in vitro study using the three-body abrasion mode10.1016/j.jdent.2019.02.010 ↗
38. Effects of crystal refining on wear behaviors and mechanical properties of lithium disilicate glass-ceramics10.1016/j.jmbbm.2018.02.023 ↗