Investigation of indentation size effect and R-curve behaviour of Li2O–SiO2 and Li2O–2SiO2 glass ceramics
Source abstract
Abstract
Indentation size effect (ISE) and R-curve behaviour of Li2O-SiO2 and Li2O-2SiO2 glass ceramics are investigated using micro-indentation and indentation-strength (IS) techniques, respectively. Vickers micro-indentations were applied on both materials at the load of 0.10-19.6 N to determine the load influence on the measured hardness. For the IS-measured fracture toughness, the load ranged from 1.96 to 19.6 N. The hardness decreased with increasing load by 20% and 18% on Li2O-SiO2 and Li2O-2SiO2 glass ceramics, respectively, indicating the ISE behaviour on both materials. The fracture toughness increased with the load by 27% and 59% on Li2O-SiO2 and Li2O-2SiO2 glass ceramics, respectively, signifying the R-curve behaviour. The ISE behaviour of both materials was analysed using the Meyer's, Hays-Kendall (HK), proportional specimen resistance (PSR), Nix-Gao (NG), modified PSR (MPSR) and elastic plastic deformation (EPD) models while the R-curve behaviour was analysed by the fractional power law. The Meyer's index of both materials was less than 2, strongly confirming the ISE existence. The HK, PSR and NG models were only suitable to determine intrinsic Vickers hardness for Li2O-2SiO2 glass ceramic while the MPSR and EPD models were successful for both materials. The fractional power law gave higher R-curve steepness for Li2O-2SiO2 than Li2O-SiO2 glass ceramics. Also, material and brittleness indices predicted, respectively, higher quasi-plasticity and better machinability for Li2O-2SiO2 than Li2O-SiO2 glass ceramics indicating superior performance in the former to the latter. Finally, this study presents a new significant insight into the micro-mechanisms of fracture tolerance behaviour of these glass ceramics which is critical to their functional performance as structural ceramics.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Metal and Thin Film Mechanics · Advanced ceramic materials synthesis · Advanced materials and composites
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (86)
Show source-provided references
1. A fundamental study of vibration assisted machining10.4028/www.scientific.net/AMR.264-265.1702 ↗
2. Alao · 2007
3. Alao · 2016
4. Elasticity, plasticity and analytical machinability prediction of lithium metasilicate/disilicate glass ceramics10.1016/j.jmbbm.2019.04.027 ↗
5. Load effect on the mechanical behaviour of zirconia-reinforced lithium silicate glass ceramic10.1016/j.ceramint.2020.08.257 ↗
6. Application of Taguchi and Box-Behnken designs for surface roughness in precision grinding of silicon10.1504/IJPTECH.2011.038107 ↗
7. Surface finish prediction models for precision grinding of silicon10.1007/s00170-011-3438-8 ↗
8. Fracture, roughness and phase transformation in CAD/CAM milling and subsequent surface treatments of lithium metasilicate/disilicate glass-ceramics10.1016/j.jmbbm.2017.06.015 ↗
9. Influence of CAD/CAM milling, sintering and surface treatments on the fatigue behavior of lithium disilicate glass ceramic10.1016/j.jmbbm.2020.104133 ↗
10. Prediction of the resistance to machining-induced cracking in zirconia by nanoindentation
11. Nano-mechanical behaviour of lithium metasilicate glass-ceramic10.1016/j.jmbbm.2015.05.002 ↗
12. Optical applications of glass-ceramics10.1016/j.jnoncrysol.2010.05.103 ↗
13. Influence of heat-treatment protocols on mechanical behavior of lithium silicate dental ceramics10.1111/ijac.13257 ↗
14. Phenomena and mechanisms of crack propagation in glass-ceramics10.1016/j.jmbbm.2007.11.005 ↗
15. Mechanical properties of (Cu0.5TI0.5)-1223 substituted by Pr10.1007/s10948-011-1150-4 ↗
16. Fatigue resistance of monolithic lithium disilicate occlusal veneers: a pilot study10.1007/s10266-019-00417-7 ↗
17. Stereolithography-based additive manufacturing of lithium disilicate glass ceramic for dental applications10.1016/j.msec.2020.111180 ↗
18. Design and properties of glass-ceramics10.1146/annurev.ms.22.080192.000515 ↗
19. Machinability and brittleness of glass-ceramics10.1016/S0924-0136(96)02275-3 ↗
20. Wear of ceramic-based dental materials10.1016/j.jmbbm.2019.01.009 ↗
21. An explanation of the indentation size effect in ceramics10.1080/09500838908206356 ↗
22. Progress in micro-indentation hardness testing
23. Bühler-Zemp
24. Analysis of indentation size effect (ISE) behavior in low-load Vickers hardness microhardness testing of (Sm123)1–x(Nd123)x10.1007/s10854-013-1082-9 ↗
25. Effect of ion exchange on R-curve behavior of a dental porcelain10.1007/s10853-010-4858-9 ↗
26. A critical evaluation of indentation techniques for measuring fracture toughness: II, strength method10.1111/j.1151-2916.1981.tb10321.x ↗
27. In-vitro strength degradation of dental ceramics and novel PICN material by sharp indentation10.1016/j.jmbbm.2013.05.004 ↗
28. Toward revealing full atomic picture of nanoindentation deformation mechanisms in Li2O-2SiO2 glass-ceramics10.1016/j.actamat.2021.116715 ↗
29. Ceramics for dental application: a review10.3390/ma3010351 ↗
30. El-Meliegy · 2012
31. Strength recovery by diffusive crack healing10.1016/0001-6160(77)90179-1 ↗
32. R-curve behavior of dental ceramic materials10.1177/154405910208100809 ↗
33. Glass-ceramics in dentistry: a review10.3390/ma13051049 ↗
34. Analysis of the nanoindentation data measured with a Berkovich indenter for brittle materials: effect of the residual contact stress10.1016/j.actamat.2003.10.013 ↗
35. Load-dependence of the measured hardness of Ti (C, N)-based cermets10.1016/S0921-5093(00)01845-1 ↗
36. Examination of the indentation size effect in low-load Vickers hardness testing of ceramics10.1016/S0955-2219(99)00043-6 ↗
37. Effect of microstructure on the mechanical properties of lithium disilicate glass-ceramics10.1016/j.jmbbm.2018.02.032 ↗
38. An analysis of Knoop microhardness10.1016/0026-0800(73)90053-0 ↗
39. Studies of crystal phase formations in high-strength lithium disilicate glass-ceramics10.1016/j.jnoncrysol.2006.06.039 ↗
40. Development of all-solid lithium-ion battery using Li-on conducting glass-ceramics10.1016/j.jpowsour.2007.06.234 ↗
41. Effects of heat treatment temperature on microstructure and mechanical properties of lithium disilicate-based glass-ceramics10.1016/j.ceramint.2018.08.223 ↗
42. Ceramics in restorative and prosthetic dentistry10.1146/annurev.matsci.27.1.443 ↗
43. Rising fracture toughness from the bending strength of indented alumina beams10.1111/j.1151-2916.1988.tb05051.x ↗
44. On the fracture toughness of advanced materials10.1002/adma.200803322 ↗
45. Micromechanics of machining and wear in hard and brittle materials10.1111/jace.17502 ↗
46. Probing material properties with sharp indenters: a retrospective10.1007/s10853-011-5865-1 ↗
47. Hardness, toughness, and brittleness: an indentation analysis10.1111/j.1151-2916.1979.tb19075.x ↗
48. Effects of crystal size on the mechanical properties of a lithium disilicate glass-ceramic10.1016/j.msea.2016.05.068 ↗
49. Strengthening of a lithium disilicate glass-ceramic by rapid cooling10.1016/j.ceramint.2018.03.240 ↗
50. The microhardness indentation load/size effect in rutile and cassiterite single crystals10.1007/BF00400874 ↗
51. The effect of indentation-induced cracking on the apparent microhardness10.1007/BF00352908 ↗
52. Effect of sintering parameters on phase evolution and strength of dental lithium silicate glass-ceramics10.1016/j.dental.2019.07.002 ↗
53. Strength characterization and lifetime prediction of dental ceramic materials10.1016/j.dental.2020.10.015 ↗
54. Determination of hardness and fracture toughness of Y-TZP manufactured by digital light processing through the indentation technique10.1155/2021/6612840 ↗
55. Untersuchungen uber harteprufung und harte
56. What can we learn from R-curve measurements?10.1111/j.1551-2916.2006.01447.x ↗
57. Indentation size effects in crystalline materials: a law for strain gradient plasticity10.1016/S0022-5096(97)00086-0 ↗
58. Microstructural development during heat treatment of a commercially available dental-grade lithium disilicate glass-ceramic10.1016/j.dental.2019.02.011 ↗
59. Wear behavior of pressable lithium disilicate glass ceramic10.1002/jbm.b.33447 ↗
60. In-lab simulation of CAD/CAM milling of lithium disilicate glass-ceramic specimens: effect on the fatigue behavior of the bonded ceramic10.1016/j.jmbbm.2021.104604 ↗
61. Digital dentistry: the new state of the art–Is it disruptive or destructive?10.1016/j.dental.2019.08.103 ↗
62. Indentation size effect of Y-TZP ceramics10.1016/j.dental.2014.08.367 ↗
63. Brittle fracture versus quasi plasticity in ceramics: a simple predictive index10.1111/j.1151-2916.2001.tb00698.x ↗
64. Review: indentation size effect, indentation cracks and microhardness measurement of brittle crystalline solids – some basic concepts and trends10.1002/crat.200900385 ↗
65. Machinability of IPS Empress ® 2 framework ceramic: potential for ceramic dentures10.1002/1097-4636(2000)53:4<348::AID-JBM8>3.0.CO;2-0 ↗
66. Internal stresses in ceramics10.1111/j.1151-2916.1961.tb15475.x ↗
67. Internal residual stresses in glass-ceramics: a review10.1016/j.jnoncrysol.2012.01.040 ↗
68. R-curve behavior and toughening mechanisms of resin-based dental composites: effects of hydration and post-cure heat treatment10.1016/j.dental.2008.12.004 ↗
69. Effect of the temperature on the mechanical properties and translucency of lithium silicate dental glass-ceramic10.1016/j.ceramint.2020.12.137 ↗
70. Emerging trends in glass-ceramic photocatalysts10.1016/j.cej.2020.126971 ↗
71. Determination of the mechanical behavior of lithium disilicate glass ceramics by nanoindentation & scanning probe microscope10.1016/j.matchemphys.2014.09.015 ↗
72. New, tough and strong lithium metasilicate dental glass-ceramic10.1016/j.ceramint.2020.09.133 ↗
73. Flexural strength, fracture toughness, three-body wear, and Martens parameters of pressable lithium-X-silicate ceramics10.1016/j.dental.2020.01.009 ↗
74. Wear behavior of dental glass-ceramics: a scoping review on the damage of opposing tooth enamel surfaces10.1016/j.biotri.2020.100116 ↗
75. Effects of heat-treatment temperature and holding time on the microstructure and mechanical properties of lithium disilicate glass-ceramics10.1016/j.jnoncrysol.2020.120502 ↗
76. Toughening of a particulate-reinforced ceramic-matrix composite by thermal residual stress10.1111/j.1151-2916.1990.tb05209.x ↗
77. Residual stress effect on the fracture toughness of lithium disilicate glass-ceramics10.1111/jace.16664 ↗
78. The science and application of IPS e.max dental ceramic10.1016/j.kjms.2018.01.012 ↗
79. Load-bearing capacity of lithium disilicate and ultra-translucent zirconias10.1016/j.jmbbm.2018.08.023 ↗
80. R-curve analysis of solid-phase-sintered and liquid-phase-sintered silicon carbide ceramics by indentation fracture and indentation-strength-in-bending methods10.1016/j.ceramint.2015.11.070 ↗
81. Manufacturing reliable ceramic crowns-The role of abrasive machining in digital dentistry
82. Relationship between elastic and mechanical properties of dental ceramics and their index of brittleness10.1016/j.ceramint.2012.02.056 ↗
83. “Digitally oriented materials”: focus on Lithium disilicate ceramics
84. Experimental measurement of residual stress field around a sharp indentation in glass10.1111/j.1151-2916.1994.tb07025.x ↗
85. Trade-off between fracture resistance and translucency of zirconia and lithium-disilicate glass ceramics for monolithic restorations10.1016/j.actbio.2019.04.043 ↗
86. Effect of heat treatment on the microstructure and properties of lithium disilicate glass-ceramics10.1016/j.jnoncrysol.2014.05.023 ↗