Influence of crystalline phase transformation induced by airborne-particle abrasion and low-temperature degradation on mechanical properties of dental zirconia ceramics stabilized with over 5 mol% yttria
Source abstract
Abstract
Monolithic dental prostheses fabricated from 5 mol% yttria-stabilized zirconia (5YZ) have been developed to improve the translucency of conventional 3 mol% yttria-stabilized zirconia. In this study, we aimed to evaluate the influence of airborne-particle abrasion (APA) and low-temperature degradation (LTD) on the mechanical properties of 5YZ in association with the crystalline phase transformation. In total, 120 disc-shaped specimens of two brands of 5YZ (Lava Esthetic and Katana UTML) were prepared. The specimens were divided into four groups (n = 15 for each group): (i) control, (ii) APA, (iii) LTD, and (iv) APA + LTD groups. APA was performed with 50 μm alumina particles, and LTD was induced by autoclaving at 134 °C for 50 h. The biaxial flexural strength of the specimens was assessed using a piston-on-three-ball test according to ISO 6872:2015, and Vickers hardness was determined using a microhardness tester. The crystalline phase was analyzed by the Rietveld refinement of X-ray diffraction patterns. APA significantly increased the flexural strength of the Lava Esthetic specimens, whereas LTD hardly affected the strength of both materials. APA and APA + LTD significantly increased the Vickers hardness of both materials. According to Rietveld analysis, the pseudocubic phase was predominant in both materials, i.e., 66 mass% and 81 mass% in the Lava Esthetic and Katana UTML specimens, respectively. APA induced the rhombohedral phase at approximately 37 mass% in both materials, while LTD induced the monoclinic phase at 2.8 mass% in the Lava Esthetic specimens and 0.9 mass% in the Katana UTML specimens. APA + LTD weakly affected the amount of the rhombohedral phase but slightly increased the amount of the monoclinic phase. These findings suggest that APA may improve the mechanical properties of 5YZ, particularly hardness, via the generation of the rhombohedral phase. In contrast, the influence of LTD on the mechanical and microstructural properties of 5YZ was limited.
Source: europepmc · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Dental materials and restorations · Dental Implant Techniques and Outcomes · Bone Tissue Engineering Materials
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (55)
Show source-provided references
1. Fatigue analysis of computer-aided design/computer-aided manufacturing resin-based composite vs. lithium disilicate glass-ceramic10.1111/eos.12278 ↗
2. 2014
3. Aging resistance, mechanical properties and translucency of different yttria-stabilized zirconia ceramics for monolithic dental crown applications10.1016/j.dental.2018.03.006 ↗
4. Hydrothermal degradation of a 3Y-TZP translucent dental ceramic: a comparison of numerical predictions with experimental data after 2 years of aging10.1016/j.dental.2015.12.015 ↗
5. Low temperature degradation of a Y-TZP dental ceramic10.1016/j.actbio.2010.09.020 ↗
6. Low-temperature aging of Y-TZP ceramics10.1111/j.1151-2916.1999.tb02055.x ↗
7. Critical effect of cubic phase on aging in 3mol% yttria-stabilized zirconia ceramics for hip replacement prosthesis10.1016/j.biomaterials.2004.01.002 ↗
8. The tetragonal-monoclinic transformation in zirconia: lessons learned and future trends10.1111/j.1551-2916.2009.03278.x ↗
9. State of the art of zirconia for dental applications10.1016/j.dental.2007.05.007 ↗
10. Influence of aging on flexural strength of translucent zirconia for monolithic restorations10.1016/j.prosdent.2016.06.010 ↗
11. Effect of airborne-particle abrasion and polishing on novel translucent zirconias: surface morphology, phase transformation and insights into bonding10.2186/jpr.JPOR_2019_524 ↗
12. Qualitative X-ray diffraction analysis of metastable tetragonal (t ') zirconia10.1111/j.1151-2916.2001.tb00708.x ↗
13. Influence of surface and heat treatments on the flexural strength of Y-TZP dental ceramic10.1016/j.jdent.2004.07.001 ↗
14. Fracture resistance of computer-aided design/computer-aided manufacturing-generated composite resin-based molar crowns10.1111/eos.12173 ↗
15. Mechanical and microstructural properties of ultra-translucent dental zirconia ceramic stabilized with 5 mol% yttria10.1016/j.jmbbm.2020.103974 ↗
16. Rhombohedral phase produced in abraded surfaces of partially stabilized Zirconia (PSZ)10.1007/BF00722220 ↗
17. Surface roughness and the flexural and bend strength of zirconia after different surface treatments10.1016/j.prosdent.2016.02.018 ↗
18. Crystallographic and morphological analysis of sandblasted highly translucent dental zirconia10.1016/j.dental.2017.12.008 ↗
19. Impact of sandblasting on the flexural strength of highly translucent zirconia10.1016/j.jmbbm.2020.104268 ↗
20. 2015
21. Fracture strength of monolithic all-ceramic crowns made of high translucent yttrium oxide-stabilized zirconium dioxide compared to porcelain-veneered crowns and lithium disilicate crowns10.3109/00016357.2013.822098 ↗
22. Effect of a rapid-cooling protocol on the optical and mechanical properties of dental monolithic zirconia containing 3-5 mol% Y2O310.3390/ma13081923 ↗
23. Concerns of hydrothermal degradation in CAD/CAM zirconia10.1177/0022034509354193 ↗
24. In vivo aging of zirconia dental ceramics - Part I: biomedical grade 3Y-TZP10.1016/j.dental.2020.11.023 ↗
25. New multi-layered zirconias: composition, microstructure and translucency10.1016/j.dental.2019.02.017 ↗
26. Origin of the hump on the left shoulder of the X-ray diffraction peaks observed in Y2O3-fully and partially stabilized ZrO210.1016/j.jallcom.2003.11.129 ↗
27. The effect of surface grinding and sandblasting on flexural strength and reliability of Y-TZP zirconia ceramic10.1016/S0109-5641(99)00070-6 ↗
28. Implant-supported full-arch zirconia-based mandibular fixed dental prostheses. Eight-year results from a clinical pilot study10.3109/00016357.2012.749518 ↗
29. Low temperature degradation -aging- of zirconia: a critical review of the relevant aspects in dentistry10.1016/j.dental.2010.04.006 ↗
30. Graded ultra-translucent zirconia (5Y-PSZ) for strength and functionalities10.1177/0022034518771287 ↗
31. Surface treatments of zirconia to enhance bonding durability10.2341/14-144-L ↗
32. Mechanical properties and low-temperature aging of tetragonal zirconia polycrystals processed by hot isostatic pressing10.1557/JMR.2003.0337 ↗
33. Critical considerations on load-to-failure test for monolithic zirconia molar crowns10.1016/j.jmbbm.2018.07.034 ↗
34. Fracture resistance of monolithic zirconia molar crowns with reduced thickness10.3109/00016357.2015.1007479 ↗
35. The influence of low-temperature degradation and cyclic loading on the fracture resistance of monolithic zirconia molar crowns10.1016/j.jmbbm.2015.03.007 ↗
36. Effect of low-temperature degradation on the mechanical and microstructural properties of tooth-colored 3Y-TZP ceramics10.1016/j.jmbbm.2015.08.031 ↗
37. Adhesion to zirconia used for dental restorations: a systematic review and meta-analysis
38. Zirconia as a ceramic biomaterial10.1016/S0142-9612(98)00010-6 ↗
39. Effect of hydrothermal treatment on light transmission of translucent zirconias10.1016/j.prosdent.2016.10.024 ↗
40. Clinical efficacy of methods for bonding to zirconia: a systematic review10.1016/j.prosdent.2019.12.017 ↗
41. A practical and systematic review of Weibull statistics for reporting strengths of dental materials10.1016/j.dental.2009.09.006 ↗
42. A correction for the alpha-1, alpha-2 doublet in the measurement of widths of X-ray diffraction lines10.1088/0950-7671/25/7/125 ↗
43. Five-year clinical results of zirconia frameworks for posterior fixed partial dentures
44. Influence of surface treatment on the resin-bonding of zirconia10.1016/j.dental.2015.03.004 ↗
45. Fracture strength and microstructure of Y-TZP zirconia after different surface treatments10.1016/S0022-3913(13)60376-5 ↗
46. Effect of different treatments on the flexural strength of fully versus partially stabilized monolithic zirconia10.1016/j.prosdent.2016.10.031 ↗
47. Load-bearing capacity and the recommended thickness of dental monolithic zirconia single crowns10.1016/j.jmbbm.2014.03.014 ↗
48. Evaluation of zirconium-oxide-based ceramic single-unit posterior fixed dental prostheses (FDPs) generated with two CAD/CAM systems compared to porcelain-fused-to-metal single-unit posterior FDPs: a 5-year clinical prospective study10.1111/j.1532-849X.2011.00825.x ↗
49. The influence of stresses on ageing kinetics of 3Y- and 4Y-stabilized zirconia10.1016/j.jeurceramsoc.2017.09.044 ↗
50. Suggested guidelines for the topographic evaluation of implant surfaces
51. Phase separation and hydrothermal degradation of 3 mol% Y2O3-ZrO2 ceramics10.2109/jcersj.113.530 ↗
52. Strength, toughness and aging stability of highly-translucent Y-TZP ceramics for dental restorations10.1016/j.dental.2016.09.025 ↗
53. Lifetime estimation of zirconia ceramics by linear ageing kinetics10.1016/j.actamat.2015.04.001 ↗
54. Trade-off between fracture resistance and translucency of zirconia and lithium-disilicate glass ceramics for monolithic restorations10.1016/j.actbio.2019.04.043 ↗
55. Novel zirconia materials in dentistry10.1177/0022034517737483 ↗