journal article·2022-02

Bending properties of additively manufactured commercially pure titanium (CPTi) limited contact dynamic compression plate (LC-DCP) constructs: Effect of surface treatment

Seungjong Lee, Nabeel Ahmad, Kayla Corriveau, Cameron Himel, Daniel F. Silva, Nima Shamsaei

Publisher page

Abstract

Additive manufacturing of metallic materials, a layer-wise manufacturing method, is currently gaining attention in the biomedical industry because of its capability to fabricate complex geometries including customized parts fitting to patient requirements. However, one of the major challenges hindering the full implementation of additively manufactured parts in safety-critical applications is their poor mechanical performance under cyclic loading. This study investigated both quasi-static bending properties (bending stiffness, bending structural stiffness, and bending strength) and bending fatigue properties of additively manufactured (AM) commercially pure titanium (CPTi) limited contact dynamic compression plate (LC-DCP) constructs based on ASTM International standard for metallic bone plates (ASTM F382). In addition, the effect of post surface treatment methods including single shot-peened (SP), dual shot-peened (DP), and chemically assisted surface enhancement (CASE) on bending fatigue performance was also evaluated. Results indicated that bending stiffness and bending structural stiffness of AM CPTi LC-DCPs are comparable to conventionally manufactured (CM) counterparts; however, the bending strength of AM CPTi LC-DCPs is lower than CM counterparts. While the fatigue strength of as-built AM CPTi LC-DCPs is lower compared to the CM counterparts, AM CPTi LC-DCPs after post surface treatments (SP, DP, and CASE) exhibit statistically comparable fatigue strength to the CM CPTi LC-DCPs.
Source: europepmc · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Additive Manufacturing Materials and Processes · Additive Manufacturing and 3D Printing Technologies · Bone Tissue Engineering Materials

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (31)

Show source-provided references
1. Improving the surface quality and mechanical properties by shot-peening of 17-4 stainless steel fabricated by additive manufacturing10.1016/j.matdes.2016.08.037 ↗
2. Standard specification and test method for metallic bone plates
3. Evaluation of the mechanical and wear properties of titanium produced by three different additive manufacturing methods for biomedical application10.1016/j.msea.2019.06.024 ↗
4. Comparative study of commercially pure titanium produced by laser engineered net shaping, selective laser melting and casting processes10.1016/j.msea.2017.08.103 ↗
5. Single cycle to failure in bending of three standard and five locking plates and plate constructs10.3415/VCOT-11-04-0061 ↗
6. Single cycle to failure in torsion of three standard and five locking plate constructs10.3415/VCOT-11-04-0050 ↗
7. Metallurgical properties of unalloyed titanium limited contact dynamic compression plates
8. Additive manufacturing of biomedical implants: a feasibility assessment via supply-chain cost analysis
9. Metal additive manufacturing: a review10.1007/s11665-014-0958-z ↗
10. Applications of metal additive manufacturing in veterinary orthopedic surgery
11. Overview of current additive manufacturing technologies and selected applications10.3184/003685012X13420984463047 ↗
12. Additive manufacturing applications in medical cases: a literature based review10.1016/j.ajme.2017.09.003 ↗
13. Improved fatigue strength of additively manufactured Ti6Al4V by surface post processing10.1016/j.ijfatigue.2020.105497 ↗
14. Characterization of the hydroxyapatite layer formed by fine hydroxyapatite particle peening and its effect on the fatigue properties of commercially pure titanium under four-point bending10.1016/j.surfcoat.2016.01.023 ↗
15. Laser polishing for improving fatigue performance of additive manufactured Ti-6Al-4V parts10.1016/j.optlastec.2020.106639 ↗
16. Fatigue behavior and modeling for additive manufactured 304L stainless steel: the effect of surface roughness10.1016/j.ijfatigue.2020.105856 ↗
17. Formation of equiaxed grains in selective laser melted pure titanium during annealing10.1016/j.jmrt.2021.01.008 ↗
18. Surface post-treatments for metal additive manufacturing: progress, challenges, and opportunities
19. Influence of defects, surface roughness and HIP on the fatigue strength of Ti-6Al-4V manufactured by additive manufacturing10.1016/j.ijfatigue.2018.07.020 ↗
20. Fatigue of additive manufactured Ti-6Al-4V, Part II: the relationship between microstructure, material cyclic properties, and component performance10.1016/j.ijfatigue.2019.105363 ↗
21. Powder-based additive manufacturing for development of tailor-made implants for orthopedic applications10.14356/kona.2015015 ↗
22. Fatigue of additive manufactured Ti-6Al-4V, Part I: the effects of powder feedstock, manufacturing, and post-process conditions on the resulting microstructure and defects10.1016/j.ijfatigue.2019.105358 ↗
23. The limited contact dynamic compression plate (LC-DCP)10.1007/BF00636166 ↗
24. Advanced mechanical properties of pure titanium with ultrafine grained structure10.1016/S1359-6462(01)01089-2 ↗
25. An overview of Direct Laser Deposition for additive manufacturing; Part II: mechanical behavior, process parameter optimization and control
26. Biomedical applications of additive manufacturing: present and future10.1016/j.cobme.2017.05.006 ↗
27. Stephens · 2000
28. An overview of Direct Laser Deposition for additive manufacturing; Part I: transport phenomena, modeling and diagnostics
29. Laser and electron beam additive manufacturing methods of fabricating titanium bone implants10.3390/app7070657 ↗
30. Comparison of conventional reconstruction plate versus direct metal laser sintering plate: an in vitro mechanical characteristics study10.1186/s13018-017-0628-6 ↗
31. Additive manufacturing of fatigue resistant materials: challenges and opportunities10.1016/j.ijfatigue.2017.01.001 ↗