Al2O3/GdAlO3 fiber for dental porcelain reinforcement
Source abstract
Abstract
The aim of this study was to test the hypothesis that the addition of continuous or milled GdAlO3/Al2O3 fibers to a dental porcelain increases its mechanical properties. Porcelain bars without reinforcement (control) were compared to those reinforced with long fibers (30 vol%). Also, disk specimens reinforced with milled fibers were produced by adding 0 (control), 5 or 10 vol% of particles. The reinforcement with continuous fibers resulted in significant increase in the uniaxial flexural strength from 91.5 to 217.4 MPa. The addition of varied amounts of milled fibers to the porcelain did not significantly affect its biaxial flexural strength compared to the control group. SEM analysis showed that the interface between the continuous fiber and the porcelain was free of defects. On the other hand, it was possible to note the presence of cracks surrounding the milled fiber/porcelain interface. In conclusion, the reinforcement of the porcelain with continuous fibers resulted in an efficient mechanism to increase its mechanical properties; however the addition of milled fibers had no significant effect on the material because the porcelain was not able to wet the ceramic particles during the firing cycle.
Source: europepmc · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Dental materials and restorations · Dental Implant Techniques and Outcomes · Dental Research and COVID-19
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (27)
Show source-provided references
1. Laser heated pedestal growth of Al2O3/GdAlO3 eutectic fibers10.1016/S0022-0248(01)01764-X ↗
2. Solidificacao direcional do eutetico Al2O3/GdAlO3 por fusao a laser10.1590/S0366-69132002000100007 ↗
3. Elasticity of single-crystal Smalo3, Gdalo3 and Scalo3 perovskites10.1016/0031-9201(84)90015-3 ↗
4. Role of interfacial carbon layer in the thermal-diffusivity conductivity of silicon–carbide fiber-reinforced reaction-bonded silicon–nitride matrix composites10.1111/j.1151-2916.1992.tb08183.x ↗
5. Callister · 2000
6. Correlation between fracture toughness and leucite content in dental porcelains10.1016/j.jdent.2005.02.001 ↗
7. Chawla · 1993
8. Modeling the ultimate tensile strength of unidirectional glass-matrix composites10.1111/j.1151-2916.2000.tb01166.x ↗
9. Raman/Cr3+ fluorescence mapping of a melt-grown Al2O3/GdAlO3 eutectic10.1016/j.jeurceramsoc.2005.01.024 ↗
10. Strength, fracture toughness and microstructure of a selection of all-ceramic materials. Part I. Pressable and alumina glass-infiltrated ceramics10.1016/j.dental.2003.05.003 ↗
11. Strength, reliability, and mode of fracture of bilayered porcelain/core ceramics
12. Preparation and mechanical properties of long alumina fiber alumina matrix composites10.1016/0167-577X(96)00051-1 ↗
13. Failure of all-ceramic fixed partial dentures in vitro and in vivo: Analysis and modeling10.1177/00220345950740060301 ↗
14. Microstructure of Al2O3/ZrO2 eutectic fibers grown by the micro-pulling down method10.1016/S0022-0248(00)00998-2 ↗
15. Microstructure of Y2O3 doped Al2O3/ZrO2 eutectic fibers grown by the micro-pulling-down method10.1016/S0022-0248(01)01451-8 ↗
16. Stress distribution of inlay-anchored adhesive fixed partial dentures: A finite element analysis of the influence of restorative materials and abutment preparation design10.1067/mpr.2002.124367 ↗
17. Tensile fracture behavior and strength of surface-modified SiTiCO fiber SiC-matrix minicomposites fabricated by the PIP process10.1111/j.1151-2916.2000.tb01213.x ↗
18. Medeiros, I., 2004, Fibras de Al2O3/GdAlO3 obtidas por fusão a laser para aplicações odontológicas. Thesis - Ciência e Engenharia de Materiais:113
19. Al2O3/GdAlO3 eutectic fibers of high modulus of rupture produced by the laser heated pedestal growth technique10.1007/s10853-006-0466-0 ↗
20. Low-temperature processing of ceramic woven fabric ceramic-matrix composites10.1111/j.1151-2916.1994.tb06962.x ↗
21. Flexural strength of a glass-infiltrated alumina dental ceramic incorporated with silicon carbide whiskers
22. Development of Al2O3 fiber-reinforced Al2O3-based ceramics10.4012/dmj.23.297 ↗
23. A ductile ceramic eutectic composite with high strength at 1,873 K10.1038/37937 ↗
24. Microstructures in oxide eutectic fibers grown by a modified micro-pulling-down method10.1016/S0022-0248(99)00265-1 ↗
25. Yoshimura, H.N., Goncalves, M., Goldenstein, H., 1997, The effects of SiCp clusters and porosity on the mechanical properties of PM Al matrix composites, In: Cmmc 96—Proceedings of the First International Conference on Ceramic and Metal Matrix Composites, Pts 1 and 2, 127-(985–992)10.4028/www.scientific.net/KEM.127-131.985 ↗
26. Stress intensity factor threshold in dental porcelains10.1007/s10856-007-3290-4 ↗
27. Effect of porosity on mechanical properties of a high purity alumina10.1590/S0366-69132005000300011 ↗