journal article·2022-12

Manufacturing hydroxyapatite scaffold from snapper scales with green phenolic granules as the space holder material

Ade Indra, Irfan Hamid, Jerry Farenza, Nofriady Handra, Anrinal, Adi Subardi

Publisher page

Abstract

Hydroxyapatite (HA) scaffold was made using the powder metallurgy with an use of a space holder method with a pore-forming agent from green phenolic (GP) granules. The novelty of this study was the use of GP granules as an agent that does not melt at high temperatures to avoid damaging the tangential contact between the HA powder during the sintering process. HA from snapper scales was added and mixed with polyvinyl alcohol (PVA) and ethanol to form a slurry. The ethanol content was then removed by drying at room temperature. The HA, which contained PVA, was added with GP granules as a pore-forming agent in various amounts to get the desired porosity. The green body was made using a stainless steel mold with the uniaxial pressing process under a pressure of 100 MPa. To make a scaffold sintered body, a sintering process ran at 1200 °C with a holding time of 2 h while maintaining the heating and cooling rates at 5 °C/min. The physical properties of the scaffold sintered body were characterized through linear shrinkage test, pore measurement, porosity test, phase observation by X-ray diffraction (XRD), and microstructure observation by scanning electron microscopy (SEM) and digital microscopy (DM). So were the mechanical ones through a compressive strength test. The results showed that the sintered body had a compressive strength value of 1.6 MPa at a porosity of 60.7% with a pore size of 129-394 μm. The scaffold contained interconnections between pores at a HA:GP ratio of 55:45 wt%, which matched the condition required for cell tissue growth. The conclusion is that GP granules are good enough to be used as a pore-making agent on scaffolds using the space holder method because they do not damage the tangential contact between the HA powder during the sintering process. However, efforts are needed to remove the remaining GP ash on the scaffold.
Source: europepmc · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Bone Tissue Engineering Materials · Additive Manufacturing and 3D Printing Technologies · Dental Implant Techniques and Outcomes

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (69)

Show source-provided references
1. Hydroxyapatite scaffold manufacturing under the space holder method: analysis of physical properties and biocompatibility
2. A hydrothermal synthesis of natural hydroxyapatite obtained from Corbicula moltkiana freshwater clams shell biowaste10.1016/j.matlet.2018.07.034 ↗
3. Progress in the advancement of porous biopolymer scaffold: tissue engineering application10.1021/acs.iecr.8b05334 ↗
4. Synthesis and characterization of porous β-tricalcium phosphate blocks10.1016/j.biomaterials.2005.03.026 ↗
5. Fabrication and properties of zirconia/hydroxyapatite composite scaffold based on digital light processing10.1016/j.ceramint.2019.09.219 ↗
6. Novel hybrid composites based on PVA/SeTiO2 nanoparticles and natural hydroxyapatite for orthopedic applications: correlations between structural, morphological and biocompatibility properties10.3390/ma13092077 ↗
7. Evolution of the microstructural and mechanical properties of hydroxyapatite bioceramics with varying sintering temperature10.1016/j.ceramint.2019.05.144 ↗
8. Assessment of osteogenesis for 3D-printed polycaprolactone/hydroxyapatite composite scaffold with enhanced exposure of hydroxyapatite using rat calvarial defect model10.1016/j.compscitech.2019.107844 ↗
9. Bovine-derived hydroxyapatite coatings deposited by high-velocity oxygen-fuel and atmospheric plasma spray processes: a comparative study10.1016/j.surfcoat.2019.125193 ↗
10. Development of bone scaffold using Puntius conchonius fish scale derived hydroxyapatite: physico-mechanical and bioactivity evaluations10.1016/j.ceramint.2019.02.044 ↗
11. Effect of hydroxyapatite fillers on the mechanical properties and osteogenesis capacity of bio-based polyurethane composite scaffolds10.1016/j.jmbbm.2018.08.028 ↗
12. Mechanical and cytotoxicity evaluation of nanostructured hydroxyapatite-bredigite scaffolds for bone regeneration10.1016/j.msec.2016.06.030 ↗
13. Synthesis and characterization of natural nano-hydroxyapatite derived from Turkey femur-bone waste10.1007/s12010-019-03046-6 ↗
14. Highly loaded hydroxyapatite microsphere/PLA porous scaffolds obtained by fused deposition modelling10.1016/j.ceramint.2018.07.297 ↗
15. Characterizations and interfacial reinforcement mechanisms of multicomponent biopolymer based scaffold10.1016/j.msec.2019.03.030 ↗
16. Microstructure and material properties of porous hydroxyapatite-zirconia nanocomposites using polymethyl methacrylate powders10.1016/j.matdes.2014.11.028 ↗
17. Fabrication of bioactive porous bredigite (Ca7MgSi4O16) scaffold via space holder method10.3139/146.111597 ↗
18. Effect of calcination temperature on characterization of natural hydroxyapatite prepared from carp fish bones10.1007/s42452-019-0396-5 ↗
19. Natural hydroxyapatite from fishbone waste for the rapid adsorption of heavy metals of aqueous effluent
20. Enhancing the physical and mechanical properties of pellet-shaped hydroxyapatite by controlling micron- and nano-sized powder ratios10.1016/j.ceramint.2020.03.136 ↗
21. A novel fabrication procedure for producing high strength hydroxyapatite ceramic scaffolds with high porosity10.1016/j.ceramint.2021.06.112 ↗
22. Behavior of sintered body properties of hydroxyapatite ceramics: effect of uniaxial pressure on green body fabrication
23. Porous carbonated hydroxyapatite-based scaffold using simple gas foaming method10.1080/21870764.2020.1770938 ↗
24. FTIR and XRD evaluation of magnesium doped hydroxyapatite/sodium alginate powder by precipitation method10.4028/www.scientific.net/KEM.791.45 ↗
25. The usability of ark clam shell (Anadara granosa) as calcium precursor to produce hydroxyapatite nanoparticle via wet chemical precipitate method in various sintering temperature10.1186/s40064-016-2824-y ↗
26. Crystallization behavior of low-cost biphasic hydroxyapatite/β-tricalcium phosphate ceramic at high sintering temperatures derived from high potential calcium waste sources10.1016/j.rinp.2018.12.025 ↗
27. Incorporation of BMP-2 nanoparticles on the surface of a 3D-printed hydroxyapatite scaffold using an ε-polycaprolactone polymer emulsion coating method for bone tissue engineering10.1016/j.colsurfb.2018.06.043 ↗
28. Preparation of novel porous calcium silicate scaffold loaded by celecoxib drug using freeze drying technique: fabrication, characterization and simulation10.1016/j.ceramint.2019.04.113 ↗
29. Porous poly-L-lactic acid scaffold reinforced by chitin fibers10.1007/s00289-005-0364-7 ↗
30. In situ study of hydroxyapatite from cattle during a controlled calcination process using HT-XRD10.1016/j.msec.2019.110020 ↗
31. In-situ XRD study of the crystal size transition of hydroxyapatite from swine bone10.1016/j.ceramint.2020.06.230 ↗
32. 3D-printed bioceramic scaffolds: from bone tissue engineering to tumor therapy10.1016/j.actbio.2018.08.026 ↗
33. Investigation of physico-mechanical behavior, permeability and wall shear stress of porous HA/PMMA composite bone scaffold10.1007/s13369-020-04467-w ↗
34. Layered manufacturing of a three-dimensional polymethyl methacrylate (PMMA) scaffold used for bone regeneration10.1080/10667857.2018.1541212 ↗
35. Preparation of hydroxyapatite/zirconia porous composites via polymeric sponge method and study the physical and bioactivity properties10.1088/1757-899X/757/1/012046 ↗
36. Gelcasting and sintering of hydroxyapatite materials: effect of particle size and Ca/P ratio on microstructural, mechanical and biological properties10.1016/j.jeurceramsoc.2021.07.025 ↗
37. 3D hydroxyapatite scaffold for bone regeneration and local drug delivery applications
38. Natural origin hydroxyapatite scaffold as potential bone tissue engineering substitute10.1016/j.ceramint.2016.08.165 ↗
39. Magnetic hydroxyapatite: a promising multifunctional platform for nanomedicine application10.2147/IJN.S147355 ↗
40. Reinforcing 13–93 bioglass scaffolds fabricated by robocasting and pressureless spark plasma sintering with graphene oxide10.1016/j.jmbbm.2019.05.016 ↗
41. Biphasic calcium phosphate scaffolds with controlled pore size distribution prepared by in-situ foaming10.1016/j.msec.2018.03.022 ↗
42. 3D printing of bone scaffolds with hybrid biomaterials10.1016/j.compositesb.2018.09.065 ↗
43. The effect of alumina additive and sintering temperature on the microstructural, physical, mechanical, and bioactivity properties of hydroxyapatite–alumina composites10.1007/s41779-019-00336-4 ↗
44. Effect of lanthanum oxide additive on the sinterability, physical/mechanical, and bioactivity properties of hydroxyapatite-alpha alumina composite10.1007/s41779-019-00336-4 ↗
45. Development of composite scaffolds for load-bearing segmental bone defects10.1155/2013/458253 ↗
46. A silica/PVA adhesive hybrid material with high transparency, thermostability and mechanical strength10.1039/C6RA25579E ↗
47. Design and fabrication of 3D printed scaffolds with a mechanical strength comparable to cortical bone to repair large bone defects10.1038/srep19468 ↗
48. Influence of MgO nanoparticles on the mechanical properties of coated hydroxyapatite nanocomposite scaffolds produced via space holder technique: fabrication, characterization and simulation10.1016/j.jmbbm.2019.03.014 ↗
49. New insights in the morphological characterization and modelling of poly(ε-caprolactone) bone scaffolds obtained by supercritical CO2 foaming10.1016/j.supflu.2020.105012 ↗
50. Green synthesis of biocompatible nanostructured hydroxyapatite from Cirrhinus mrigala fish scale – a biowaste to biomaterial10.1016/j.ceramint.2019.01.086 ↗
51. Developing porous diopside/hydroxyapatite bio-composite scaffolds via a combination of freeze-drying and coating process10.1016/j.ceramint.2019.01.236 ↗
52. Fabrication and characterization of nanobiocomposite scaffold of zein/chitosan/nanohydroxyapatite prepared by freeze-drying method for bone tissue engineering10.1016/j.ijbiomac.2017.11.017 ↗
53. Custom repair of mandibular bone defects with 3D printed bioceramic scaffolds10.1177/0022034517734846 ↗
54. Composite biomaterial scaffolds for cardiac tissue engineering10.1179/1743280415Y.0000000012 ↗
55. Characterization of natural hydroxyapatite originated from fish bone and its biocompatibility with osteoblasts
56. Biocompatibility of sol-gel hydroxyapatite-titania composite and bilayer coatings10.1016/j.msec.2016.11.129 ↗
57. Fabrication of multiple-layered gradient cellular metal scaffold via electron beam melting for segmental bone reconstruction10.1016/j.matdes.2017.07.059 ↗
58. Processing of porous hydroxyapatite scaffold processing of porous hydroxyapatite scaffold
59. Biocompatibility, physico-chemical and mechanical properties of hydroxyapatite-based silicon dioxide nanocomposites for biomedical applications10.1016/j.ceramint.2020.06.132 ↗
60. Ink-substrate interactions during 3D printing revealed by time-resolved coherent X-ray scattering
61. Synthesis, characterization, in vitro biocompatibility and antibacterial properties study of nanocomposite materials based on hydroxyapatite-biphasic ZnO micro- and nanoparticles embedded in Alginate matrix10.1016/j.msec.2019.109965 ↗
62. Biodegradable and biocompatible systems based on hydroxyapatite nanoparticles10.3390/app7010060 ↗
63. Spectral characterization of hydroxyapatite extracted from Black Sumatra and Fighting cock bone samples: a comparative analysis10.1016/j.sjbs.2020.11.020 ↗
64. Mechanical properties and biocompatibility of the sputtered Ti doped hydroxyapatite10.1016/j.jmbbm.2016.06.025 ↗
65. Pore morphology effects on the fibrovascular tissue growth in porous polymer substrates10.1177/096368979400300411 ↗
66. Hydroxyapatite-polyethylene composites for bone substitution: effects of ceramic particle size and morphology10.1016/S0142-9612(98)00154-9 ↗
67. Extraction of natural hydroxyapatite from tilapia fish scales using alkaline treatment10.1016/j.matpr.2019.06.072 ↗
68. 3D printing of hydroxyapatite scaffolds with good mechanical and biocompatible properties by digital light processing10.1007/s10853-018-1992-2 ↗
69. Spark plasma sintering of macroporous calcium phosphate scaffolds from nanocrystalline powders10.1016/j.jeurceramsoc.2007.07.012 ↗