Fracture load in double keyhole notch PLA-Cu2O nanocomposites manufactured via compression molding and 3D printing: An experimental and numerical study
Source abstract
Abstract
Polylactic acid (PLA) polymer has garnered significant attention due to its biocompatibility. The incorporation of copper oxide (Cu2O) nanoparticles into this polymer is expected to enhance its antibacterial, electrical, and thermal properties. This modification can potentially improve the performance of PLA in the fields of prosthetics manufacturing or printed circuit fabrication. However, the current research is rather focused on the mechanical properties of the PLA-Cu2O nanocomposites. This research is thus aimed to analyze PLA-Cu2O (97-3 wt%) nanocomposites with a double keyhole notch configuration both experimentally and numerically. Scanning electron microscopy (SEM), X-ray diffraction (XRD), energy dispersive X-ray spectroscopy (EDX), X-ray mapping of elemental distribution(X-map), and thermogravimetric analysis (TGA) were employed to explore the morphology, crystallinity, homogeneity, purity, and thermal stability of the nanocomposite. The specimens were fabricated through two different processes: the classical method of compression molding and the innovative method of 3D printing. The results revealed the superior mechanical performance of the 3D-printed nanocomposite at a 0° raster angle, while the mechanical properties gradually decreased for raster angles of 45° and 90°. The experimental test also indicated a decline in the maximum fracture load of specimens with a double keyhole notch and constant notch inclination angle by raising the notch radius. This behavior was also observed by increasing the notch inclination angle at constant notch radius. The numerical results were similar to the experimental findings. Moreover, the nanocomposite manufactured through the classical method exhibited higher critical fracture load compared to their 3D-printed counterparts with the same geometry.
Source: europepmc · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Bone Tissue Engineering Materials · Additive Manufacturing and 3D Printing Technologies · Orthopaedic implants and arthroplasty
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (40)
Show source-provided references
1. Additive manufacturing and mechanical performance of carbon fiber reinforced Polyamide-6 composites
2. Fracture assessment of U-notches under mixed mode loading: two procedures based on the ‘equivalent local mode I’concept10.1007/s10704-008-9213-7 ↗
3. An investigation of PLA/W parts quality fabricated by FFF10.1080/10426914.2021.1944193 ↗
4. Fracture assessment of inclined double keyhole notches in polylactic acid specimens fabricated by fused deposition modeling and traditional method
5. A review on fiber reinforced composite printing via FFF10.1108/RPJ-01-2019-0004 ↗
6. Modeling and optimization of flexural properties of FDM-processed PET-G specimens using RSM and GWO algorithm10.1016/j.engfailanal.2022.106340 ↗
7. A global sustainability perspective on 3D printing technologies10.1016/j.enpol.2014.08.033 ↗
8. Gross · 2017
9. Effect of raster angle on mechanical properties of 3D printed short carbon fiber reinforced acrylonitrile butadiene styrene
10. 3D printing parametric optimization using the power of Taguchi design: an expository paradigm
11. Fused filament fabrication parameter adjustments for sustainable 3D printing10.1080/10426914.2023.2176872 ↗
12. An investigation of the effects of ironing parameters on the surface and compression properties of material extrusion components utilizing a hybrid-modeling experimental approach
13. Brewing sustainability and strength: biocomposite development through tea waste incorporation in polylactic acid
14. Fracture and load-carrying capacity of 3D-printed cracked components10.1016/j.eml.2020.100692 ↗
15. Some expressions for the strain energy in a finite volume surrounding the root of blunt V-notches10.1007/s10704-005-3943-6 ↗
16. A generalized stress intensity factor to be applied to rounded V-shaped notches10.1016/j.ijsolstr.2005.03.007 ↗
17. A finite-volume-energy based approach to predict the static and fatigue behavior of components with sharp V-shaped notches10.1023/A:1013595930617 ↗
18. Optimization of 3D printing parameters for high‐performance biodegradable materials10.1002/app.50782 ↗
19. Artificial neural network algorithms for 3D printing10.3390/ma14010163 ↗
20. Comparative study of crystallite size using Williamson-Hall and Debye-Scherrer plots for ZnO nanoparticles10.1088/2043-6254/ab52f7 ↗
21. Affordable biocidal ultraviolet cured cuprous oxide filled vat photopolymerization resin nanocomposites with enhanced mechanical properties10.3390/biomimetics7010012 ↗
22. Multifunctional material extrusion 3D-printed antibacterial polylactic acid (PLA) with binary inclusions: the effect of cuprous oxide and cellulose nanofibers10.3390/fib10060052 ↗
23. Fracture assessment of inclined double keyhole notches in isostatic graphite10.1134/S1029959918020030 ↗
24. Experimental determination of the tensile strength of fused deposition modeling parts
25. The mechanical testing and performance analysis of polymer-fibre composites prepared through the additive manufacturing10.1016/j.polymertesting.2020.106925 ↗
26. A special theory of crack propagation
27. On the applicability of composite PA6-TiO2 filaments for the rapid prototyping of innovative materials and structures10.1016/j.compositesb.2018.01.032 ↗
28. Ductile fracture assessment of high-density polyethylene (HDPE-PE100) weakened by an inclined double keyhole notch10.1016/j.tafmec.2019.102349 ↗
29. A review on Cu2O-based composites in photocatalysis: synthesis, modification, and applications10.3390/molecules28145576 ↗
30. On the strain rate sensitivity of fused filament fabrication (Fff) processed pla, abs, petg, pa6, and pp thermoplastic polymers10.3390/polym12122924 ↗
31. Sustainable additive manufacturing: mechanical response of polypropylene over multiple recycling processes10.3390/su13010159 ↗
32. Sustainable additive manufacturing: mechanical response of polyamide 12 over multiple recycling processes10.3390/ma14020466 ↗
33. Enhanced mechanical, thermal and antimicrobial properties of additively manufactured polylactic acid with optimized nano silica content10.3390/nano11041012 ↗
34. Fused filament fabrication three-dimensional printing Multi-Functional of polylactic acid/carbon black nanocomposites
35. Parameter effects and process modelling of Polyamide 12 3D-printed parts strength and toughness10.1080/10426914.2022.2030871 ↗
36. Development and optimization of medical-grade multi-functional polyamide 12-cuprous Oxide nanocomposites with superior mechanical and antibacterial properties for cost-effective 3D printing10.3390/nano12030534 ↗
37. Energy consumption versus strength in MEΧ 3D printing of polylactic acid10.1016/j.aime.2023.100119 ↗
38. Nanocomposites with optimized polytetrafluoroethylene content as a reinforcement agent in PA12 and PLA for material extrusion additive manufacturing10.3390/polym15132786 ↗
39. Failure criteria for brittle elastic materials10.1023/B:FRAC.0000022244.31825.3b ↗
40. Enhancement on mechanical and thermal properties of PLA biocomposites due to the addition of hybrid sisal fibers10.1080/15440478.2017.1302382 ↗