journal article·2026-01Open access

Electron beam powder bed fusion additive manufacturing of Ti6Al4V alloy lattice structures: orientation-dependent fatigue strength and crack growth behaviour under compressive cyclic loading

Yawen Huang, Zhan Wen Chen

Abstract

Sufficiently high fatigue strength is required for lattices made using electron beam powder bed fusion (EBPBF) for hip implants and understanding the anisotropic fatigue behaviour of EBPBF lattices is necessary for implant design. In this work, the combined effects of loading direction (LD) and cell orientation of EBPBF-Ti6Al4V lattices on the fatigue strength of the structures under cyclic compressive loading have been studied. Simple cubic (SC) ([001]//LD, [011]//LD and [111]//LD) lattices with a relative density of 0.36 were EBPBF made, tested and examined. The fatigue strength of [001]//LD lattices has been determined to be ∼190MPa at 5×10 6 cycles, ∼8 times higher than that of [011]//LD or [111]//LD lattices. The low fatigue strength of the non-[001]//LD lattices resulted from crack initiation readily occurring in the high tension locations, which are the top and bottom locations of each unit cell. Sideway growth of cracks leading to fracturing along (001) will be shown. This failure mechanism is absent in [001]//LD lattices and thus their fatigue strength is high. Examining the data in the literature has shown that fatigue strength values of all non-SC lattice structures are low, likely due to the same failure mechanism identified for non-[001]//LD SC lattices in this study.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Additive Manufacturing Materials and Processes · Additive Manufacturing and 3D Printing Technologies · Titanium Alloys Microstructure and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (36)

Show source-provided references
1. Influence of relative density on quasi-static and fatigue failure of lattice structures in Ti6Al4V produced by laser powder bed fusion10.1038/s41598-021-98631-3 ↗
2. 2023
3. Test methods of compression testing of metallic materials at room temperature
4. Synthetic bone: design by additive manufacturing10.1016/j.actbio.2019.07.049 ↗
5. Architected cellular materials: a review on their mechanical properties towards fatigue-tolerant design and fabrication10.1016/j.mser.2021.100606 ↗
6. Fatigue behaviour of diamond based Ti-6Al-4V lattice structures produced by laser powder bed fusion: on the effect of load direction
7. Unveiling additively manufactured cellular structures in hip implants: a comprehensive review10.1007/s00170-023-12769-0 ↗
8. Properties and applications of additively manufactured metallic cellular materials: a review10.1016/j.pmatsci.2021.100918 ↗
9. Multiaxial fatigue of additively manufactured metallic components: a review of the failure mechanisms and fatigue life prediction methodologies10.1016/j.pmatsci.2023.101126 ↗
10. Actual state-of-the-art of electron beam powder bed fusion
11. On the design evolution of hip implants: a review10.1016/j.matdes.2022.110552 ↗
12. Mechanical properties of additively manufactured metal lattice structures: data review and design interface
13. Compression‐compression fatigue of selective electron beam melted cellular titanium (Ti‐6Al‐4V)10.1002/jbm.b.31901 ↗
14. Electron beam powder bed fusion additive manufacturing of Ti6Al4V alloy lattice structures: orientation-dependent compressive strength and fracture behavior10.1007/s00170-024-13539-2 ↗
15. Influence of heat treatment on the mechanical performance of Ti21S octet truss lattice structure fabricated by laser powder bed fusion10.1007/s40964-023-00494-9 ↗
16. Failure mechanisms of additively manufactured porous biomaterials: effects of porosity and type of unit cell10.1016/j.jmbbm.2015.06.012 ↗
17. Continuous and pulsed selective laser melting of Ti6Al4V lattice structures: effect of post-processing on microstructural anisotropy and fatigue behaviour
18. A review of technological improvements in laser-based powder bed fusion of metal printers10.1007/s00170-020-05361-3 ↗
19. Development of lattice structure with selective laser melting process: a state of the art on properties, future trends and challenges10.1016/j.jmapro.2022.07.051 ↗
20. Compression fatigue behavior of Ti–6Al–4V mesh arrays fabricated by electron beam melting10.1016/j.actamat.2011.10.051 ↗
21. Influence of cell shape on mechanical properties of Ti–6Al–4V meshes fabricated by electron beam melting method10.1016/j.actbio.2014.06.010 ↗
22. The influence of selective laser melting defects on the fatigue properties of Ti6Al4V porosity graded gyroids for bone implants10.1016/j.ijmecsci.2020.106180 ↗
23. Finite element modelling and characterization of 3D cellular microstructures for the design of a cementless biomimetic porous hip stem10.1016/j.matdes.2018.04.002 ↗
24. Mechanical performance and fatigue life prediction of lattice structures: parametric computational approach10.1016/j.compstruct.2019.111821 ↗
25. Influence of structure-determining parameters on the mechanical properties and damage behavior of electron beam melted lattice structures under quasi-static and fatigue compression loading10.1016/j.matlet.2021.129380 ↗
26. Quasi‐static compression and compression–compression fatigue behavior of regular and irregular cellular biomaterials10.1111/ffe.13422 ↗
27. Fatigue behavior of Ti-6Al-4V cellular structures fabricated by additive manufacturing technique10.1016/j.jmst.2018.09.066 ↗
28. Fatigue of structures and materials
29. Laser and electron-beam powder-bed additive manufacturing of metallic implants: a review on processes, materials and designs10.1002/jor.23075 ↗
30. Compressive fatigue properties of additive-manufactured Ti-6Al-4V cellular material with different porosities10.1016/j.msea.2020.139695 ↗
31. Uniaxial compression properties and compression fatigue performance of selective laser melted Ti–6Al–4V cellular structure10.1007/s12540-021-01021-7 ↗
32. Fatigue performance of beta titanium alloy topological porous structures fabricated by laser powder bed fusion10.1016/j.jmrt.2024.02.190 ↗
33. Fatigue properties of Ti-6Al-4V Gyroid graded lattice structures fabricated by laser powder bed fusion with lateral loading
34. Heat treatment enhancing the compressive fatigue properties of open-cellular Ti-6Al-4V alloy prototypes fabricated by electron beam melting10.1016/j.jmst.2017.12.003 ↗
35. The influence of cell morphology on the compressive fatigue behavior of Ti-6Al-4V meshes fabricated by electron beam melting10.1016/j.jmbbm.2016.01.034 ↗
36. Advanced porous hip implants: a comprehensive review