Nanoindentation and the indentation size effect: Kinetics of deformation and strain gradient plasticity
Source abstract
Abstract
Abstract A study of the indentation size effect (ISE) in aluminum and alpha brass is presented. The study employs rate effects to examine the fundamental mechanisms responsible for the ISE. These rate effects are characterized in terms of the rate sensitivity of the hardness, ∂ H/ ∂ ln e eff , where H is the hardness and e eff is an effective strain rate in the plastic volume beneath the indenter. ∂ H/ ∂ ln e eff can be measured using indentation creep, load relaxation, or rate change experiments. The activation volume V ∗ , calculated based on ∂ H/ ∂ ln e eff which can traditionally be used to compare rate sensitivity data from a hardness test to conventional uniaxial testing, is calculated. Using materials with different stacking fault energy and specimens with different levels of work hardening, we demonstrate how increasing the dislocation density affects V ∗ ; these effects may be taken as a kinetic signature of dislocation strengthening mechanisms. We noticed both H and ∂ H/ ∂ ln e eff (V ∗ ) exhibit an ISE. The course of V ∗ vs. H as a result of the ISE is consistent with the course of testing specimens with different level of work hardening. This result was observed in both materials. This suggests that a dislocation mechanism is responsible for the ISE. When the results are fitted to a strain gradient plasticity model, the data at deep indents (microhardness and large nanoindentation) exhibit a straight-line behavior closely identical to literature data. However, for shallow indents (nanoindentation data), the slope of the line severely changes, decreasing by a factor of 10, resulting in a “bilinear behavior”.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and mechanical properties · Metal and Thin Film Mechanics · Boron and Carbon Nanomaterials Research
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (45)
Show source-provided references
1. Lattice incompatibility and a gradient theory of crystal plasticity10.1016/S0022-5096(99)00075-7 ↗
2. The deformation of plastically non-homogeneous alloys10.1080/14786437008238426 ↗
3. Origin of the indentation size effect in indentation of metals10.1016/0020-7403(91)90006-O ↗
4. Mode of deformation and the Cottrell-Stokes Law in FCC single crystal
5. Boyer, H.E., Gall, T.L., 1985. In: Metals Handbook. ASM, Metals park, OH, USA, pp. 723–724.
6. Brammar, I.S., Dewey, M.A.P., 1966. Blackwell Scientific Publication, Oxford.
7. Work hardening of polycrystalline copper and alpha brasses10.1179/msc.1984.18.3.123 ↗
8. Impression creep; a new creep test10.1007/BF00552241 ↗
9. The role of indentation depth on the measured hardness of materials10.1557/PROC-308-613 ↗
10. A method for interpreting the data from a depth sensing indentation instruments10.1557/JMR.1986.0601 ↗
11. Dodd · 1999
12. Elmustafa, A.A., Stone, D.S., 1999. Indentation size effect: a kinetic perspective. In: Chung, Y-W., Dunand, D.C. (Eds), The Julia R. Weertman Symposium on Advanced Materials for the 21st Century, TMS, pp. 311–321.
13. Elmustafa, A.A., Stone, D.S., 2001. Stacking fault energy and dynamic recovery: do they really impact the indentation size effect, in preparation.
14. Indentation size effect: large grained aluminum versus nanocrystalline aluminum-zirconium alloys10.1016/S1359-6462(00)00520-0 ↗
15. Strain gradient plasticity: theory and experiment10.1016/0956-7151(94)90502-9 ↗
16. Mechanism-based strain gradient Plasticity—I10.1016/S0022-5096(98)00103-3 ↗
17. Modeling plasticity at the Micrometer scale10.1007/s001140050665 ↗
18. A gradient theory of single-crystal viscoplasticity that accounts for geometrically necessary dislocations10.1016/S0022-5096(01)00104-1 ↗
19. Preparation and properties of ultra thin anodic valve metal oxide films10.4028/www.scientific.net/MSF.185-188.581 ↗
20. Mechanism-based strain gradient Plasticity—II10.1016/S0022-5096(99)00022-8 ↗
21. Fracture in mechanism-based strain gradient plasticity10.1016/S0022-5096(00)00070-3 ↗
22. Elastic analysis of some punch problems for a layered medium10.1016/0020-7683(87)90116-8 ↗
23. The mechanisms of indentation creep10.1016/0956-7151(91)90043-Z ↗
24. The frictional component of the indentation size effect in low load microhardness testing10.1557/JMR.1993.1028 ↗
25. Size dependent hardness in silver single crystals10.1557/JMR.1995.0853 ↗
26. The oxidation of the α and β phases of brass studied by XPS and nuclear reaction spectroscopy10.1016/0039-6028(80)90439-2 ↗
27. McClintock, F.A., Argon, A.S., 1966. Mechanical Behavior of Materials. Addison-Wesley, New York, USA, pp. 176–177.
28. Determination of indenter tip geometry and indentation contact area for depth-sensing indentation experiments10.1557/JMR.1998.0185 ↗
29. Kinetics of flow and strain-hardening10.1016/0001-6160(81)90112-7 ↗
30. Mott, B.W., 1956. Microindentation Hardness Testing. Butterworths, London, UK, pp. 9–10.
31. Indentation size effects in crystalline materials: a law for strain gradient plasticity10.1016/S0022-5096(97)00086-0 ↗
32. Some geometrical relations in dislocated crystal10.1016/0001-6160(53)90054-6 ↗
33. Microhardness of annealed and work-hardened copper polycrystals10.1016/1359-6462(95)00524-2 ↗
34. Samuels, L.E., 1986. Microindentation in Metals. ASTM STP 889, Philadelphia, PA, pp. 5–25.
35. Sargent, P.M., 1986. Use of the Indentation Size Effect on Microhardness for Materials Characterization. ASTM STP 889, Philadelphia, PA, pp. 160–174.10.1520/STP32956S ↗
36. Microindentation on W and Mo oriented single crystals: an STM study10.1016/0956-7151(93)90100-7 ↗
37. Elasticity analysis to aid in extracting thin film elastic moduli from continuous indentation data
38. Division of the hardness of molybdenum into rate-dependent and rate-independent components10.1557/JMR.1994.2524 ↗
39. Hardness and elastic modulus of TiN based on continuous indentation technique and new correlation10.1116/1.577270 ↗
40. Hassen plot analysis of the Hall-Petch effect in Cu/Nb nanolayer composites10.1557/JMR.1999.0059 ↗
41. Comments on “a model for nano-indentation creep”10.1016/S0956-716X(99)80026-0 ↗
42. Yoder, K.B., Stone, D.S., 1993. Load-and-depth-sensing indentation tester for properties measurements at non-ambient temperatures. In: MRS, Pittsburgh, PA, p. 308.10.1557/PROC-308-121 ↗
43. Elastic rebound between an indenter and a layered specimen: Part II. Using contact stiffness to help ensure reliability of nanoindentation measurements10.1557/JMR.1998.0436 ↗
44. An elastic-plastic indentation model and its solution10.1557/JMR.1996.0299 ↗
45. Cold work hardening in stages IV and V of FCC metals—I. Experiments and interpretation10.1016/0956-7151(93)90088-A ↗