journal article·2000-04

Cohesive zone modeling of crack nucleation at bimaterial corners

Ilyas Mohammed, Kenneth M Liechti

Publisher page

Abstract

The prediction of crack nucleation from bimaterial corners that have the same corner angle (and therefore singularity) via stress intensity factors is fairly well established. The objective of this work was to examine crack nucleation from a range of corner angles and see if a more general crack nucleation criterion could be formulated. A series of experiments was conducted using an aluminum-epoxy bimaterial specimen loaded under 4-point bending. In addition to the usual measurements of load and an associated displacement, the displacements near the corner were measured using moire interferometry. Numerical analyses were first conducted assuming a rigid interface. However, the resulting displacements differed from the measured ones, especially near the corner and along the interface. The interface was then modeled as a separate constitutive entity by incorporating a cohesive zone model in the numerical analysis. Following calibration via an interface crack configuration (zero corner angle), the cohesive zone model yielded displacements that were in good agreement with the measured values for all the other corner angles that were considered. The predicted failure loads were also in good agreement with the experimental results. Thus the consistent nucleation criterion was that the area under the traction-separation curve and its maximum traction (the dominant cohesive zone model parameters) remain the same. The numerical solutions indicated that the plastic deformation in the epoxy was small and that failure was predominantly in opening mode. In addition, the critical vectorial crack opening displacement and mode-mix were independent of the corner angle. Finally, a simple design parameter was proposed for predicting the failure load of a bimaterial specimen with an arbitrary corner angle, based on the failure load of a bimaterial specimen with an interface crack.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Mechanical Behavior of Composites · Numerical methods in engineering · Fatigue and fracture mechanics

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (32)

Show source-provided references
1. Two edge-bonded elastic wedges of different materials and wedge angles under surface tractions10.1115/1.3408786 ↗
2. High sensitivity Moiré interferometry with a compact achromatic interferometer10.1016/0143-8166(90)90029-9 ↗
3. Edge-bonded dissimilar orthogonal elastic wedges10.1115/1.3564739 ↗
4. The singularity at the apex of a rigid wedge embedded in a nonlinear material10.1115/1.3173683 ↗
5. Mixed mode energy release rates for adhesively bonded beam specimens10.1520/CTR10412J ↗
6. A fracture criterion for edge-bonded bimaterial bodies10.1177/002199838201600601 ↗
7. Stress singularities in a two-material wedge10.1007/BF00184307 ↗
8. Criteria for crack propagation at ceramic interfaces
9. Lambros · 1995 · 451 · 711
10. Interfacial stress singularities at free edge of hybrid metal matrix composites10.1115/1.3226008 ↗
11. Crack propagation at material interfaces, II: experiments in mode interaction10.1007/BF02325405 ↗
12. Mohammed, I., 1998. Crack Nucleation from Bimaterial Corners, Ph.D. dissertation, University of Texas at Austin, Engineering Mechanics Research Laboratory Report EMRL 98-21.
13. Stresses near the free edge of the interface in ceramic-to-metal joints10.1016/0955-2219(94)90024-8 ↗
14. A continuum model for void nucleation by inclusion debonding10.1115/1.3173064 ↗
15. An analysis of tensile decohesion along an interface10.1016/0022-5096(90)90001-K ↗
16. Experimental crack tip displacement analysis under small-scale yielding conditions10.1016/0142-1123(86)90058-7 ↗
17. Intensity of the stress singularity at the interface corner between a bonded elastic and rigid layer10.1016/0013-7944(90)90113-U ↗
18. Free edge stress intensity factor for a bonded ductile layer subjected to shear10.1115/1.2900863 ↗
19. Butt joint tensile strength: interface corner stress intensity factor prediction10.1163/156856195X01148 ↗
20. Comparison of butt tensile strength data with interface corner stress intensity factor prediction10.1016/0020-7683(93)90204-K ↗
21. Hybrid Moiré-numerical stress analysis around cutouts in loaded composites10.1007/BF02328582 ↗
22. Stress singularities formed at a point formed by a dissimilar elastic-plastic materials under mechanical loading10.1007/BF00018781 ↗
23. Shirani, A., Liechti, K.M., 2000. A calibrated fracture process zone model for thin film blistering. International Journal of Fracture (in press).10.1023/A:1007698426810 ↗
24. A contour integral computation of mixed-mode stress intensity factors10.1007/BF00032831 ↗
25. Asymmetric shielding mechanisms in the mixed-mode fracture of a glass/epoxy interface10.1115/1.2789035 ↗
26. The intrinsic toughness and adhesion of a glass epoxy interface10.1016/S0022-5096(98)00084-2 ↗
27. The stress intensity factor in bonded quarter planes after a change in temperature10.1080/00218469508009974 ↗
28. The relation between crack growth resistance and fracture process parameters in elastic–plastic solids10.1016/0022-5096(92)90020-3 ↗
29. The influence of plasticity on mixed mode interface toughness10.1016/0022-5096(93)90057-M ↗
30. Toughness of ductile adhesive joints10.1016/0022-5096(96)00011-7 ↗
31. Stress singularities resulting from various boundary conditions in angular corners of plates in extension10.1115/1.4010553 ↗
32. Application of Moiré techniques in fracture analysis10.1016/0308-0161(87)90013-5 ↗