The mechanical strength of polysilicon films: Part 2. Size effects associated with elliptical and circular perforations
Source abstract
Abstract
Abstract A systematic study of failure initiation in small-scale specimens has been performed to assess the effect of size scale on “failure properties” by drawing on the classical analysis of elliptically perforated specimens. Limitations imposed by photolithography restricted the minimum radii of curvature of the specimen perforations to one micron. By varying the radius of curvature and the size of the ellipses, the effects of domain size and stress concentration amplitude could be assessed separately to the point where the size of individual grains (∼0.3 μm ) becomes important. The measurements demonstrate a strong influence of the domain size under elevated stress on the “failure strength” of MEMS scale specimens, while the amplitude, or the variation, of the stress concentration factor is less significant. In agreement with probabilistic considerations of failure, the “local failure strength” at the root of a notch clearly increases as the radius of curvature becomes smaller. Accordingly, the statistical scatter also increases with decreasing size of the (super)stressed domain. When the notch radius becomes as small as 1 μm the failure stress increases on average by a factor of two relative to the tension values derived from unnotched specimens. This effect becomes moderate for larger radii of curvature, up to a radius of 8 μm (25 times the grain size), for which the failure stress at the notch tip closely approaches the value of the tensile strength for un-notched tensile configurations. We deduce that standard tests, performed on micron-sized, non-perforated, tension specimens, provide conservative strength values for design purposes. In addition, a Weibull analysis shows for surface-micromachined specimens a dependence of the strength on the specimen length, rather than the surface area or volume, which implies that the sidewall geometry, dimensions and surface conditions can dominate the failure process.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced MEMS and NEMS Technologies · Advanced Surface Polishing Techniques · Force Microscopy Techniques and Applications
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (29)
Show source-provided references
1. Ashby · 1998
2. The fracture toughness of polysilicon microdevices10.1557/JMR.1997.0131 ↗
3. On the estimation of the Weibull modulus10.1007/BF00719924 ↗
4. Calculated elastic constants for stress problems associated with semiconductor devices10.1063/1.1661935 ↗
5. Chasiotis, I., Knauss, W.G., 2001. The influence of fabrication governed surface conditions on the mechanical strength of thin film materials. Materials Research Society Symposium Proceedings 657, pp. EE2.2.1–EE2.2.6.10.1557/PROC-657-EE2.2 ↗
6. Chasiotis, I., Knauss, W.G., 2002a. Size effects determined from tensile tests of perforated MEMS scale specimens. Materials Research Society Symposium Proceedings 687, pp. B2.4.1–B2.4.6.10.1557/PROC-687-B2.4 ↗
7. A new microtensile tester for the study of MEMS materials with the aid of atomic force microscopy10.1007/BF02411051 ↗
8. Chasiotis, I., Knauss, W.G., 2003. The mechanical strength of polysilicon films: 1. The influence of fabrication governed surface conditions. J. Mech. Phys. Solids,10.1016/S0022-5096(03)00051-6 ↗
9. Specimen size effect on mechanical properties of Polysilicon Microcantilever beams measured by deflection using a Nanoindenter10.1016/S0921-5107(00)00794-7 ↗
10. The phenomena of rupture and flow in solids10.1098/rsta.1921.0006 ↗
11. A review of the Weibull distribution10.1080/00224065.1993.11979431 ↗
12. Stresses in a plate due to the presence of cracks and sharp corners
13. On the tension of a strip with a central elliptic hole10.1299/kikai1938.21.514 ↗
14. Isida, M., Nakagawa, K., 1954. On the stress gradients in tension and bending of a perforated strip. Proceedings of the Third Japan National Congress for Applied Mechanics, pp. 1–4.
15. On the fracture toughness of polysilicon MEMS structures
16. Koester, D.A., Mahadevan, R., Hardy, B., Markus, K.W., 2001. MUMPs Design Handbook. Revision 6.0.
17. Cross Comparison of Direct Strength Testing Techniques on Polysilicon Films
18. Lekhnitskii, S.G., Tsai, S.W., Cheron, T., 1968. Anisotropic Plates, 2nd Edition. Gordon and Breach Science Publishers, London, 167.
19. Namazu, T, Isono, Y., Tanaka, T., 2000. Nano-scale bending test of Si beam for MEMS. In: Proceedings IEEE Thirteenth Annual International Conference on MicroElectro-Mechanical Systems, pp. 205–210.10.1109/MEMSYS.2000.838517 ↗
20. Neuber, H., 1946. Theory of Notch Stresses, Edwards Bros Inc., Ann Arbor, Michigan.
21. Sharpe, W.N., Brown, J.S., Johnson, G.C., Knauss, W.G., 1998. Round-robin Tests of Modulus and Strength of Polysilicon. Materials Research Society Proceedings, Vol. 518, San Francisco, CA, pp. 57–65.10.1557/PROC-518-57 ↗
22. Effect of specimen size on Young's Modulus and fracture strength of polysilicon10.1109/84.946774 ↗
23. An evaluation of the probabilistic approach to Brittle design10.1016/0013-7944(80)90058-2 ↗
24. Lattice trapping and surface reconstruction for silicon cleavage on (111). Ab-initio quantum molecular dynamics calculations10.1016/0956-7151(93)90096-B ↗
25. Experimental probability estimators for Weibull Plots10.1007/BF01729379 ↗
26. Laminated composites containing an elliptical opening. I. Approximate stress analyses and fracture models10.1177/002199838702101004 ↗
27. Finite width correction factors for anisotropic plate containing a central opening10.1177/002199838802201105 ↗
28. Tensile testing of Polycrystalline Silicon thin films using electrostatic force grip
29. Specimen size effect on tensile strength of surface-micromachined polycrystalline silicon thin films10.1109/84.661392 ↗