Deep penetration of ultra-high molecular weight polyethylene composites by a sharp-tipped punch
Source abstract
Abstract
The penetration of unidirectional (UD) and [0o/90o] cross-ply ultra-high molecular weight polyethylene fibre composites by sharp-tipped cylindrical punches has been investigated. While the measured penetration pressure for both composite types increased with decreasing punch diameter, the pressure was significantly higher for the cross-ply composites and increased with decreasing ply thickness. A combination of optical microscopy and X-ray tomography revealed that in both composites, the sharp-tipped punch penetrated without fibre fracture by the formation of mode-I cracks along the fibre directions, followed by the wedging open of the crack by the advancing punch. In the cross-ply composites, delamination between adjacent 0o and 90o plies also occurred to accommodate the incompatible deformation between plies containing orthogonal mode-I cracks. Micromechanical models for the steady-state penetration pressure were developed for both composites. To account for material anisotropy as well as the large shear strains and fibre rotations, the deformation of the composites was modelled via a pressure-dependent crystal plasticity framework. Intra and inter-ply fracture were accounted for via mode-I and delamination toughnesses respectively. These models account for the competition between deformation and fracture of the plies and accurately predict the measured steady-state penetration pressures over the wide range of punch diameters and ply thicknesses investigated here. Design maps for the penetration resistance of cross-ply composites were constructed using these models and subsequently used to infer composite designs that maximise the penetration resistance for a user prescribed value of fibre strength.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Mechanical Behavior of Composites · Polymer crystallization and properties · Mechanical stress and fatigue analysis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (37)
Show source-provided references
1. Anderson · 2005
2. Micromechanics of crystals and polycrystals10.1016/S0065-2156(08)70242-4 ↗
3. Overview no. 42 texture development and strain hardening in rate dependent polycrystals10.1016/0001-6160(85)90188-9 ↗
4. The out-of-plane compressive response of Dyneema composites10.1016/j.jmps.2014.05.017 ↗
5. Mechanisms of the penetration of ultra-high molecular weight polyethylene composite beams10.1016/j.ijimpeng.2016.02.010 ↗
6. Improving stab-resistant textile materials with a non-woven fabric structure10.4188/jte.62.37 ↗
7. Two-dimensional (2D) fabrics and three-dimensional (3D) preforms for ballistic and stabbing protection: a review10.1177/0040517516669075 ↗
8. Ballistic impact into fabric and compliant composite laminates10.1016/S0263-8223(03)00029-1 ↗
9. Modeling unidirectional composites by bundling fibers into strips with experimental determination of shear and compression properties at high pressures10.1016/j.compscitech.2014.06.016 ↗
10. Dimensionless parameters for optimization of textile-based body armor systems
11. Stab resistance of shear thickening fluid (STF)-treated fabrics10.1016/j.compscitech.2006.08.007 ↗
12. Tensile strength and work of fracture of oriented polyethylene fibre10.1016/0032-3861(95)96848-3 ↗
13. A ballistic material model for cross-plied unidirectional ultra-high molecular-weight polyethylene fiber-reinforced armor-grade composites10.1016/j.msea.2008.07.056 ↗
14. Ballistic depth of penetration studies in Dyneema® composites
15. Constitutive analysis of elastic-plastic crystals at arbitrary strain10.1016/0022-5096(72)90017-8 ↗
16. High velocity impact and armour design10.3144/expresspolymlett.2011.26 ↗
17. Polyethylene ballistic laminates: failure mechanics and interface effect10.1016/j.matdes.2014.05.069 ↗
18. The soft impact response of composite laminate beams10.1016/j.ijimpeng.2013.04.002 ↗
19. Dynamic contact responses of laminated composite plates according to the impactor's shapes10.1016/S0045-7949(95)00408-4 ↗
20. An assessment of experimental techniques for measuring the mode I fracture toughness of uhmw-pe composites
21. Dynamic stab resistance of ultra-high molecular weight polyethylene fabric impregnated with shear thickening fluid10.1016/j.matdes.2016.04.006 ↗
22. Collapse of a composite beam made from ultra high molecular-weight polyethylene fibres10.1016/j.jmps.2013.08.021 ↗
23. Stab and puncture characterization of thermoplastic-impregnated aramid fabrics10.1016/j.ijimpeng.2009.03.006 ↗
24. High velocity perforation behaviour of polymer composite laminates10.1016/S0734-743X(99)00019-6 ↗
25. The effect of impactor shape on the impact response of composite laminates10.1016/j.compstruct.2004.09.007 ↗
26. Constitutive model for the shear response of Dyneema® fiber composites10.1016/j.compositesa.2014.06.012 ↗
27. Indentation of polyethylene laminates by a flat-bottomed cylindrical punch10.1016/j.compositesa.2015.10.015 ↗
28. Mechanisms of penetration in polyethylene reinforced cross-ply laminates10.1016/j.ijimpeng.2015.08.012 ↗
29. Ballistic penetration response of glass fibre reinforced polyester (Gfrp) composites
30. A new membrane model for the ballistic impact response and V50 performance of multi-ply fibrous systems10.1016/S0020-7683(03)00329-9 ↗
31. The high strain rate response of ultra high molecular-weight polyethylene: from fibre to laminate10.1016/j.ijimpeng.2013.03.010 ↗
32. Mechanisms of deep penetration of soft solids, with application to the injection and wounding of skin10.1098/rspa.2004.1315 ↗
33. Ultra-high strength polyethylene filaments by solution spinning/drawing10.1007/BF02396802 ↗
34. Ultrahigh-strength polyethylene filaments by solution spinning and hot drawing10.1007/BF00256272 ↗
35. High performance dyneema fibres in composites10.1016/S0261-3069(89)80021-4 ↗
36. Predicting the penetration and perforation of FRP laminates struck normally by projectiles with different nose shapes10.1016/S0263-8223(00)00064-7 ↗
37. Tensile creep and recovery in ultra-high modulus linear polyethylenes10.1016/0032-3861(78)90208-2 ↗