Influence of Spray Materials and Their Surface Oxidation on the Critical Velocity in Cold Spraying
Source abstract
Abstract
Abstract Critical velocity is an important parameter in cold spraying. It determines the deposition efficiency under a given spray condition. It depends not only on material types, but also particle temperature and oxidation conditions. In this present work, three types of materials including copper, 316L stainless steel, and Monel alloy were used to deposit coatings by cold spraying. The critical velocities of spray materials were determined using a novel measurement method. Oxygen content in three powders was changed by isothermal oxidation at ambient atmosphere. The effect of oxygen content on the critical velocity was examined. It was found that critical velocity was significantly influenced by particle oxidation besides material properties. The critical velocity of Cu particles increased from about 300 m/s to over 610 m/s with a change in oxygen content in the powder. The results suggest that with a severely oxidized powder, critical velocity tends to be dominated by the oxide on the powder rather than material properties.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: High-Temperature Coating Behaviors · Advanced ceramic materials synthesis · Advanced materials and composites
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (26)
Show source-provided references
1. A.P. Alkimov, V.F. Kosarev, and A.N. Papyrin, A Method of Cold Gas Dynamic Deposition, Dokl. Akad. Nauk SSSR, 1990, 318, p 1062-1065
2. A. Papyrin, V. Kosarev, K.V. Klinkov, A. Alkhimov, and V.M. Fomin, Cold Spray Technology, A. Papyrin, Ed., Elsevier, Oxford, 2006
3. V.K. Champagne, The Cold Spray Materials Deposition Process: Fundamentals and Applications, Woodhead Publishing Limited, Cambridge, 2007
4. R.G. Maev and V. Leshchinsky, Introduction to Low Pressure Gas Dynamic Spray: Physics & Technology, Wiley-VCH Verlag GmbH, Weinheim, 2008
5. E. Irissou, J.G. Legoux, A.N. Ryabinin, B. Jodoin, and C. Moreau, Review on Cold Spray Process and Technology: Part I—Intellectual Property, J. Therm. Spray Technol., 2008, 17(4), p 495-51610.1007/s11666-008-9203-3 ↗
6. H.-J. Kim, C.-H. Lee, and S.-Y. Hwang, Superhard Nano WC–12%Co Coating by Cold Spray Deposition, Mater. Sci. Eng. A, 2005, 391, p 243-24810.1016/j.msea.2004.08.082 ↗
7. J. Akedo, Room Temperature Impact Consolidation (RTIC) of Fine Ceramic Powder by Aerosol Deposition Method and Applications to Microdevices, J. Therm. Spray Technol., 2008, 17(2), p 181-19810.1007/s11666-008-9163-7 ↗
8. H. Assadi, F. Gärtner, T. Stoltenhoff, and H. Kreye, Bonding Mechanism in Cold Gas Spraying, Acta Mater., 2003, 51(15), p 4379-439410.1016/S1359-6454(03)00274-X ↗
9. C.-J. Li, W.-Y. Li, and H.-L. Liao, Examination of the Critical Velocity for Deposition of Particles in Cold Spraying, J. Therm. Spray Technol., 2006, 15(2), p 212-22210.1361/105996306X108093 ↗
10. D.L. Gilmore, R.C. Dykhuizen, R.A. Neiser, T.J. Roemer, and M.F. Smith, Particle Velocity and Deposition Efficiency in the Cold Spray Process, J. Therm. Spray Technol., 1999, 8(4), p 576-58210.1361/105996399770350278 ↗
11. T. Schmid, F. Gärtner, H. Assadi, and H. Kreye, Development of a Generalized Parameter Window for a Cold Spray Deposition, Acta Mater., 2006, 54(3), p 729-74210.1016/j.actamat.2005.10.005 ↗
12. T.H. Van Steenkiste, J.R. Smith, R.E. Teets, J.J. Moleski, D.W. Gorkiewicz, R.P. Tison, D.R. Marantz, K.A. Kowalsky, W.L. Riggs, P.H. Zajchowski, B. Pilsner, R.C. McCune, and K.J. Barnett, Kinetic Spray Coatings, Surf. Coat. Technol., 1999, 111(1), p 62-7110.1016/S0257-8972(98)00709-9 ↗
13. T. Stoltenhoff, J. Voyer, and H. Kreye, Cold Spraying—State of the Art and Applicability, International Thermal Spray Conference, E. Lugscheider and C.C. Berndt, Ed., March 4-6, 2002 (Essen, Germany), DVS Deutscher Verband für Schweißen, 2002, p 366-37410.31399/asm.cp.itsc2002p0366 ↗
14. D. Zhang, P.H. Shipway, and D.G. McCartney, Particle-Substrate Interactions in Cold Gas Dynamic Spraying, Thermal Spray 2003: Advancing the Science and Applying the Technology, Vol 1, B.R. Marple and C. Moreau, Ed., May 5-8, 2003 (Orlando, FL), ASM International, 2003, p 45-4810.31399/asm.cp.itsc2003p0045 ↗
15. K. Kang, S. Yoon, Y. Ji, and C.H. Lee, Oxidation Dependency of Critical Velocity for Aluminum Feedstock Deposition in Kinetic Spraying Process, Mater. Sci. Eng. A, 2008, 486, p 300-30710.1016/j.msea.2007.09.010 ↗
16. R.C. Dykuizen and M.F. Smith, Gas Dynamic Principles of Cold Spray, J. Therm. Spray Technol., 1998, 7, p 205-21210.1361/105996398770350945 ↗
17. T. Stoltenhoff, H. Kreye, and H.J. Richter, An Analysis of the Cold Spray and Its Coatings, J. Therm. Spray Technol., 2002, 11, p 542-55010.1361/105996302770348682 ↗
18. F. Gärtner, T. Stoltenhoff, T. Schmidt, and H. Kreye, The Cold Spray Process and Its Potential for Industrial Applications, Thermal Spray Connects: Explore Its Surfacing Potential, E. Lugscheider, Ed., May 2-4, 2005 (Basel, Switzerland), DVS Deutscher Verband für Schweißen, 2005, p 158-16310.31399/asm.cp.itsc2005p0158 ↗
19. M. Grujicic, C.L. Zhao, W.S. DeRosset, and D. Helfritch, Adiabatic Shear Instability Based Mechanism for Particle/substrate Bonding in the Cold-Gas Dynamic-Spray Process, Mater. Des., 2004, 25, p 681-68810.1016/j.matdes.2004.03.008 ↗
20. G. Bae, Y. Xiong, S. Kumar, K. Kang, and C.H. Lee, General Aspects of Interface Bonding in Kinetic Sprayed Coatings, Acta Mater., 2008, 56, p 4858-486810.1016/j.actamat.2008.06.003 ↗
21. F. Gärtner, T. Stoltenhoff, T. Schmidt, and H. Kreye, The Cold Spray Process and Its Potential for Industrial Applications, J. Therm. Spray Technol., 2006, 15(2), p 223-23210.1361/105996306X108110 ↗
22. C.-J. Li, W.-Y. Li, Y.-Y. Wang, G.-J. Yang, and H. Fukanuma, A Theoretical Model for Prediction of Deposition Efficiency in Cold Spraying, Thin Solid Films, 2005, 485(1-2), p 79-85
23. W.-Y. Li and C.-J. Li, Optimization of Spray Conditions in Cold Spraying Based on the Numerical Analysis of Particle Velocity, Trans. Nonferrous Met. Soc. China, 2004, 14(Special 2), p 43-48
24. C. Borchers, T. Schmid, F. Gartner, H. Assadi, and H. Kreye, High Strain Deformation Microstructures of Stainless Steel of 316L by Cold Spraying and Explosive Powder Compaction, Appl. Phys. A, 2008, 90(2), p 517-52610.1007/s00339-007-4314-0 ↗
25. L.B. Temples, M.F.Grununger, and C.H. Londry, Influences of Oxygen Content on MCrAlY’s, Thermal Spray Coatings: Research, Design and Applications, C.C. Berndt and T.F. Bernecki, Ed., June 7-11, 1993 (Anaheim, CA), ASM International, 1993, p 359-363
26. C.-J. Li and W.-Y. Li, Effect of Sprayed Powder Particle Size on the Oxidation Behavior of MCrAlY Materials During HVOF Deposition, Surf. Coat. Technol., 2003, 162(1), p 21-41