journal article·2007-12

Characterization of Nanostructured WC-Co Deposited by Cold Spraying

Chang-Jiu Li, Guan-Jun Yang, Pei-Hu Gao, Jian Ma, Yu-Yue Wang, Cheng-Xin Li

Journal of Thermal Spray Technology· Volume 16· Issue 5-6
Publisher page

Abstract

Nanostructured WC-Co coating was deposited by cold spraying using a nanostructured WC-12Co powder. The critical velocity for the particle to deposit was measured. The coating microstructure was characterized by X-ray diffraction analysis, scanning electron microscopy, and transmission electron microscopy. The coating hardness was tested using a Vickers hardness tester. The deposition behavior of single WC-Co particle was examined. WC particle size was measured for comparison of deposit properties to that of sintered bulk. The result shows that the nanostructured WC-Co coating can be successfully deposited by cold spraying using nanostructured powders. The coating exhibited a dense microstructure with full retention of the original nanostructure in the powder to the coating. The test of microhardness of the coating yielded a value of over 1820 Hv0.3, which is comparable to that of sintered nanostructured WC-Co. The deposition behavior of WC-Co powders as superhard cermet materials in cold spraying and powder structure effects is discussed.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced materials and composites · High-Temperature Coating Behaviors · Metal Alloys Wear and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (50)

Show source-provided references
1. C.-J. Li, A. Ohmori, Y. Harada 1996 Effect of Powder Structure on the Structure of Thermally Sprayed WC-Co Coatings. J. Mater. Sci. 31, 785–79410.1007/BF00367900 ↗
2. H. Lovelock 1998 Powder/Processing/Structure Relationships in WC-Co Thermal Spray Coatings: A Review of the Published Literature. J. Thermal Spray Technol., 7, 357–37310.1361/105996398770350846 ↗
3. D.A. Stewart, P.H. Shipway, D.G. McCartney 1999 Abrasive Wear Behavior of Conventional and Nanocomposite HVOF-Sprayed WC-Co Coatings. Wear, 229, 789–79810.1016/S0043-1648(99)00032-0 ↗
4. M. E. Vinayo, F. Kassabji, J. Guyonnet, P. Fauchais, 1985 Plasam Sprayed WC-Co Coatings: Influence of Spray Conditions (Atmospheric and Low Pressure Plasma Spraying) on the Crystal Structure, Porosity, and Hardness. J. Vac. Sci. Technol. A, 3, 2483–248910.1116/1.572863 ↗
5. J. Subrahmanyam, M.P. Srivastava, R. Sivakumar, 1986 Characterization of Plasma-Sprayed WC-Co Coatings. Mater. Sci. Eng., 84, 209–21410.1016/0025-5416(86)90240-5 ↗
6. S. Rangaswamy and H. Herman, Metallurgical Characterization of Plasma Sprayed WC-Co Coatings, Advances in Thermal Spraying (Proceedings of 11th International Thermal Spray Conference), September 8-12, 1986 (Montreal, Canada), Welding Institute of Canada, Pergamon Press Canada Ltd., 1986, p 101-11010.1016/B978-0-08-031878-3.50014-9 ↗
7. A. Tronche, P. Fauchais 1987 Hard Coatings (Cr2O3, WC-Co) Properties on Aluminium or Steel Substrates. Mater. Sci. Eng., 92, 133–14410.1016/0025-5416(87)90163-7 ↗
8. V. Ramnnath, N. Jayaraman 1989 Characterization and Wear Performance of Plasma Sprayed WC-Co Coatings. Mater. Sci. Technol., 5, 382–38810.1179/mst.1989.5.4.382 ↗
9. G. Barbezat, E. Muller, B. Walser 1988 Applying Tungsten Carbide Cobalt Coatings by High Velocity Combustion Spraying. Sulzer Tech. Rev., 4, 27–33
10. H. Kreye, D. Fandrich, H.-H. Muller, and G. Reiners, Microstructure and Bond Strength of WC-Co Coatings Deposited by Hypersonic Flame Spraying (Jet-Kote Process), Advances in Thermal Spraying (Proceedings of 11th International Thermal Spray Conference), September 8-12, 1986 (Montreal, Canada), Welding Institute of Canada, Pergamon Press Canada Ltd., 1986, p 121-12810.1016/B978-0-08-031878-3.50016-2 ↗
11. H. Nakahira, Y. Harada, and K. Tani, Properties of Tungsten Cermet Coatings by High Energy Flame Spraying, Proceedings of International Symposium on Advanced Thermal Spray Technology and Allied Coatings, A. Ohmori, Ed., May 13-15, 1988 (Osaka, Japan), Japan High Temperature Society, 1988, p 79-88
12. C.-J. Li, A. Ohmori, Y. Harada 1996 Formation of an Amorphous Phase in Thermally Sprayed WC-Co. J. Thermal Spray Technol., 5(1), 69–7310.1007/BF02647520 ↗
13. Y. Ishikawa, J. Kawakita, S. Osawa, T. Itsukaichi, Y. Sakamoto, M. Takaya, S. Kuroda 2005 Evaluation of Corrosion and Wear Resistance of Hard Cermet Coatings Sprayed by Using an Improved HVOF Process. J. Thermal Spray Technol., 14(3), 384–39510.1361/105996305X59378 ↗
14. C.-J. Li, Y.-Y. Wang, G.-J. Yang, A. Ohmori, K. A. Khor 2004 Effect of Solid Carbide Particle Size on Deposition Behavior, Microstructure and Wear Performance of HVOF Cermet Coatings. Mater. Sci. Technol., 20, 1087–109610.1179/026708304225019722 ↗
15. V. Richter, M.V. Ruthendorf 1999 On Hardness and Toughness of Ultrafine and Nanocrystalline Hard Materials. Int. J. Refractory Met. Hard Mater., 17, 141–15210.1016/S0263-4368(99)00003-7 ↗
16. K. Jia, T.E. Fischer 1996 Abrasion Resistance of Nanostructured and Conventional Cemented Carbides. Wear, 200, 206–21410.1016/S0043-1648(96)07277-8 ↗
17. J.H. He, M. Ice, S. Dallek, E.J. Lavernia 2000 Synthesis of Nanostructured WC-12 pct Co Coating Using Mechanical Milling and High-Velocity Oxygen Fuel Thermal Spraying. Metall. Mater. Trans. A, 31, 541–55310.1007/s11661-000-0289-6 ↗
18. D.A. Steward, P.H. Shipway, D.G. McCartney 2000 Microstructural Evolution in Thermally Sprayed WC-Co Coatings: Comparison Between Nanocomposite and Conventional Starting Powders. ACTA Mater., 48, 1593–160410.1016/S1359-6454(99)00440-1 ↗
19. Y.F. Qiao, Y.R. Liu, and T.E. Fischer (USA), Sliding and Abrasive Wear Resistance of Thermal-Sprayed WC-CO Coatings, J. Thermal Spray Technol., 2001, 10, p 118-12510.1361/105996301770349583 ↗
20. J.H. He, L. Ajdelsztajn, E.J. Lavernia 2001 Thermal Stability of Nanocrystalline WC-Co Powder Synthesized by Using Mechanical Milling at Low Temperature. J. Mater. Res., 16, 478–48810.1557/JMR.2001.0071 ↗
21. J.H. He, Y.R. Liu, Y.F. Qiao, T.E. Fischer, E.J. Lavernia 2002 Near-Nanostructured WC-18 pct Co Coatings with Low Amounts of Non-WC Carbide Phase. Part I. Synthesis and Characterization. Metall. Mater. Trans. A, 33, 145–15710.1007/s11661-002-0013-9 ↗
22. Z.G. Ban, L.L. Shaw 2002 Synthesis and Processing of Nanostructured WC-Co Materials. J. Mater. Sci., 37, 3397–340310.1023/A:1016553426227 ↗
23. Z.G. Ban, L.L. Shaw 2003 Characterization of Thermal Sprayed Nanostructured WC-Co Coatings Derived from Nanocrystalline WC-18 wt.%Co Powders. J. Thermal Spray Technol., 12, 112–11910.1361/105996303770348564 ↗
24. Y-.Y. Wang, C.-J. Li, J. Ma, G.-J. Yang 2004 Effect of Flame Conditions on the Abrasive Wear Performance of HVOF Sprayed Nanostructured WC-12Co Coatings. Trans. Nonferrous Met. Soc. China, 14(special 2), 72–76
25. J.H. He, J.M. Schoenung 2004 Nanostructured Coatings. Mater. Sci. Eng. A, 336, 274–31910.1016/S0921-5093(01)01986-4 ↗
26. P.H. Shipway, D.G. McCartney, T. Sudaprasert 2005 Sliding Wear Behaviour of Conventional and Nanostructured HVOF Sprayed WC-Co Coatings. Wear, 259, 820–82710.1016/j.wear.2005.02.059 ↗
27. J.M Guilemany, S. Dosta, J. Nin, J.R. Miguel 2005 Study of the Properties of WC-Co Nanostructured Coatings Sprayed by High-Velocity Oxyfuel. J Thermal Spray Technol., 14(3), 405–41310.1361/105996305X59350 ↗
28. C. Bartuli, T. Valente, F. Cipri, E. Bemporad, M. Tului 2005 Parametric Study of an HVOF Process for the Deposition of Nanostructured WC-Co Coatings. J. Thermal Spray Technol., 14(2), 187–19510.1361/10599630523746 ↗
29. B.R. Marple, R. S. Lima 2005 Process Temperature/Velocity-Hardness-Wear Relationship for High-Velocity Oxyfuel Sprayed Nanostructured and Conventional Cermet Coatings. J. Thermal Spray Technol., 14(1), 67–7610.1361/10599630522729 ↗
30. J. O. Berghaus, B. Marple, C. Moreau 2006 Suspension Plasma Spraying of Nanostructured WC-12Co Coatings. J. Thermal Spray Technol., 15(4), 676–68110.1361/105996306X147072 ↗
31. Y.-C. Zhu, K. Yukimura, C.-X. Ding, and P.-Y. Zhang, Tribological Properties of Nanostructured and Conventional WC-Co Coatings Deposited by Plasma Spraying, Thin Solid Films, 2001, 388, p 277-28210.1016/S0040-6090(01)00805-7 ↗
32. G. Skandan, R. Yao, R. Sadangi, B.H. Kear, Y. Qiao, L. Liu, T.E. Fischer 2000 Multimodal Coatings: A New Concept in Thermal Spraying. J. Thermal Spray Technol., 9(3), 329–33110.1361/105996300770349755 ↗
33. D.A. Ateward, H.P. Shipway, D.C. McCartney 1999 Abrasive Wear Behaviour of Conventional And Nanocomposite HVOF-Sprayed WC-Co Coatings. Wear, 225-229, 789-79810.1016/S0043-1648(99)00032-0 ↗
34. C.-J. Li, A. Ohmori 2002 Relationship Between the Structure and Properties of Thermally Sprayed Deposits. J. Thermal Spray Technol., 11, 365–37410.1361/105996302770348754 ↗
35. C.-J. Li, W.-Y. Li, W.-H. Ma, and H. Fukanuma, Characterization of Microstructure of Nanostructured Fe–Si Coating Deposited by Cold Spraying, Thermal Spray 2004: Advances in Technology and Application, May 10-12, 2004 (Osaka, Japan), DVS, 2004, p 371–37710.31399/asm.cp.itsc2004p0371 ↗
36. H.-T. Wang, C.-J. Li, G.-J. Yang, and C.-X. Li, Formation of Fe–Al Intermetallic Compound Coating Through Cold Spraying, Building on 100 Years of Success: Proceedings of the 2006 International Thermal Spray Conference, B.R. Marple, M.M. Hyland, Y.C. Lau, R.S. Lima, and J. Voyer, Eds., May 15-18, 2006 (Seattle, WA, USA), ASM International, 200610.31399/asm.cp.itsc2006p0157 ↗
37. H.-T. Wang, C.-J. Li, G.-J. Yang, C.-X. Li, and Q. Zhang, Microstructural Characterization of Cold-sprayed FeAl Intermetallic Compound Coatings, J. Thermal Spray Technol., 2007, in this issue10.31399/asm.cp.itsc2007p0135 ↗
38. Q. Zhang, C.-J. Li, C.-X. Li, G.-J. Yang, and X.-R. Wang, Preliminary Study of Oxidation Behavior of Cold Sprayed Nanostructure NiCrAlY Bond Coatings, Global Coating Solutions: Proceedings of the 2007 International Thermal Spray Conference, B.R. Marple, M.M. Hyland, Y.-C. Lau, C.-J. Li, R.S. Lima, and G. Montavon, Eds., May 14-16, 2007 (Beijing, China), ASM International, 200710.31399/asm.cp.itsc2007p0457 ↗
39. L. Ajdelsztajn, A.Zuniga, B. Jodoin, E.J. Lavernia 2006 Cold-Spray Processing of a Nanocrystalline Al-Cu-Mg-Fe-Ni Alloy with Sc. J. Thermal Spray Technol., 15, 184–19010.1361/105996306X107995 ↗
40. R.S. Lima, J. Karthikeyan, C.M. Kay, J. Lindemann, C.C. Berndt 2002 Microstructural Characteristics of Cold-sprayed Nanostructured WC-Co Coating. Thin Solid Films, 416, 129–13510.1016/S0040-6090(02)00631-4 ↗
41. H.-J. Kim, C.-H. Lee, S.-Y. Hwang 2005 Superhard Nano WC-12%Co Coating by Cold Spray Deposition. Mater. Sci. Eng. A, 391, 243–24810.1016/j.msea.2004.08.082 ↗
42. H.-J. Kim, C.-H. Lee, S.-Y. Hwang 2005 Fabrication of WC-Co Coatings by Cold Spray Deposition. Surf. Coat. Technol., 191, 335–34010.1016/j.surfcoat.2004.04.058 ↗
43. C.-J. Li, W.-Y. Li 2003 Deposition Characteristics of Titanium Coating in Cold Spraying. Surf. Coat. Technol., 167, 278–28310.1016/S0257-8972(02)00919-2 ↗
44. C.-J. Li, W.-Y. Li, H.-L. Liao 2006 Examination of the Critical Velocity for Deposition of Particles in Cold Spraying. J. Thermal Spray Technol., 15, 212–22210.1361/105996306X108093 ↗
45. C.-J. Li, W.-Y. Li, Y.-Y. Wang, G.-J. Yang, H. Fukanuma 2005 A Theoretical Model for Prediction of Deposition Efficiency in Cold Spraying. Thin Solid Films, 489, 79–8510.1016/j.tsf.2005.05.002 ↗
46. C.-J. Li, W.-Y. Li 2004 Optimization of Spray Conditions in Cold Spraying based on the Numerical Analysis of Particle Velocity. Trans. Nonferrous Met. Soc. China, 14(special 2), 43–48
47. S.-Q. Fan, G.-J. Yang, G.-J. Liu, C.-X. Li, C.-J. Li, L.-Z. Zhang, 2006 Characterization of Microstructure of TiO2 Coating Deposited by Vacuum Cold Spraying. J. Thermal Spray Technol., 15(4), 613–517
48. J. He, J. M. Schoenung 2002 A Review on Nanostructured WC-Co Coatings. Surf. Coat. Technol., 157, 72–7910.1016/S0257-8972(02)00141-X ↗
49. Y. Qiao, T. E. Fischer, A. Dent 2003 The effects of Fuel Chemistry and Feedstock Powder Structure on the Mechanical and Tribological Properties of HVOF Thermal-Sprayed WC-Co Coatings with Very Fine Structure. Surf. Coat. Technol., 172, 24–4110.1016/S0257-8972(03)00242-1 ↗
50. D.A. Atewart, P.H. Shipway, D.G. McCartney 1998 Influence of Heat Treatment on the Abrasive Wear Behavior of HVOF Sprayed WC-Co Coatings. Surf. Coat. Technol., 105, 13–2410.1016/S0257-8972(98)00444-7 ↗