Effect of Various Heat Treatments on the Microstructure of 316L Austenitic Stainless Steel Coatings Obtained by Cold Spray
Source abstract
Abstract
Industries developing cold spray aim at dense and resistant coatings for component repair. However, as-sprayed 316L coatings display non-equilibrium microstructure and brittle fracture behavior. Improving their mechanical properties requires controlling their microstructure; post-spraying heat treatment is a promising approach. The recovery and recrystallization of coatings were little studied, and heat treatments reported in literature mostly used holding for long time in furnaces, not adapted to on-site repairs. This study aimed at gaining insights into recovery and recrystallization mechanisms of 316L coatings, for a broader range of heat treatment kinetics. A study of powders and as-sprayed coatings was conducted to characterize the initial state. In situ XRD measurements provided input for heat treatment definition. Microscopy, room temperature XRD and hardness measurements allowed to better understand the microstructural evolutions and to select treatments leading to original microstructures. In this work, a variety of microstructures were produced by adapting heat treatment conditions for a given set of spraying parameters. The recrystallization path of the heterogeneous skin-core microstructure of deposited particles, as well as the interaction between grain growth and precipitation was revealed. A novel, optimized fast heat treatment led to a fully recrystallized, fine-grained coating and significantly reduced hardness.
Source: europepmc · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: High-Temperature Coating Behaviors · Advanced materials and composites · Nuclear Materials and Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (37)
Show source-provided references
1. H. Assadi, F. Gärtner, T. Stoltenhoff and H. Kreye, Bonding Mechanism in Cold Gas Spraying, Acta Mater., 2003, 51, p 4379-4394. https://doi.org/10.1016/S1359-6454(03)00274-X10.1016/S1359-6454(03)00274-X ↗
2. S. Adachi and N. Ueda, Effect of Cold-Spray Conditions using a Nitrogen Propellant Gas in AISI 316L Stainless Steel Coating Microstructures, Coat., 2017, 7, p 87-96. https://doi.org/10.3390/coatings707008710.3390/coatings7070087 ↗
3. R. Maestracci, Influence de la Microstructure sur les Mécanismes D’endommagement Thermomécanique de Revêtements à base d’acier Inoxydable AISI 316L Réalisés Par Projection Dynamique Par Gaz Froid « cold spray » (Influence of the microstructure on the thermomechanical damage mechanisms of AISI 316L stainless steel coatings produced by cold spray), PhD thesis, MINES ParisTech, 2016, https://pastel.archives-ouvertes.fr/tel-01561419, in French
4. X. Jiang, N. Overmann, C. Smith and K. Ross, Microstructure, Hardness and Cavitation Erosion Resistance of Different Cold Spray Coatings on Stainless Steel 316 for Hydropower Applications, Mater. Today Commun., 2020, 25, p 101305. https://doi.org/10.1016/j.mtcomm.2020.10130510.1016/j.mtcomm.2020.101305 ↗
5. C. Widener, M. Carter, O. Ozdemir, R. Hrabe, B. Hoiland, T. Stamey, V. Champagne and T.J. Eden, Application of High Pressure Cold Spray for an Internal Bore Repair if a Navy Valve Actuator, J. Therm. Spray Technol., 2016, 25, p 193-201. https://doi.org/10.1007/s11666-015-0366-410.1007/s11666-015-0366-4 ↗
6. V. Champagne and D. Helfritch, Critical Assessment 11 Structural Repairs by Cold Spray, J. Mater. Sci. Technol., 2015, 31, p 627-634. https://doi.org/10.1179/1743284714Y.000000072310.1179/1743284714Y.0000000723 ↗
7. Y. Hu, F. Renteria, C. Cahoon and M. Floyd, U.S. Patent App. 10/930,506, (2006)
8. A. Debiccari, J. Haynes, U.S. Patent App. 11/003,140, (2006)
9. A. Debiccari, J. Haynes and D. Rutz, U.S. Patent App. 11/019,871, (2006)10.1088/1126-6708/2006/11/019 ↗
10. D. Raybould, M.N. Madhava, V. Chung, T.R. Duffy and M. Floyd, U.S. Patent 7,455,881, (2008)
11. K. Ogawa, D. Seo, Repair of Turbine Blades using Cold Spray Technique, Advances in Gas Turbine Technology, Dr. Ernesto Benin (Ed.), Intech, p 500-525, (2011) https://doi.org/10.5772/2362310.5772/23623 ↗
12. R. Huang, M. Sone, W. Ma and H. Fukanuma, The Effects of Heat Treatments on the Mechanical Properties of Cold-Sprayed Coatings, Surf. Coat. Technol., 2015, 261, p 278-288. https://doi.org/10.1016/2014.11.01710.1016/2014.11.017 ↗
13. G. Sundararajan, P.S. Phani, A. Jyothirmayi and R.C. Gundakaram, The influence of heat treatment on the microstructural, mechanical and corrosion behaviour of cold sprayed SS 316L coatings, J. Mater. Sci., 2009, 44, p 2320-2326. https://doi.org/10.1007/s10853-008-3200-210.1007/s10853-008-3200-2 ↗
14. B. Al-Mangour, P. Vo, R. Mongrain, E. Irissou and S. Yue, Effect of Heat Treatment on the Microstructure and Mechanical Properties of Stainless Steel 316L Coatings Produced by Cold Spray for Biomedical Application, J. Therm. Spray Technol., 2014, 23, p 641-652. https://doi.org/10.1007/s11666-017-0640-810.1007/s11666-017-0640-8 ↗
15. B. Dikici, H. Yilmazer, I. Ozdemir and M. Isik, The Effet of Post-Heat Treatment on Microstructure of 316L Cold-Sprayed Coatings and their Corrosion Performance, J. Therm. Spray Technol., 2016, 25, p 704-714. https://doi.org/10.1007/s11666-016-0402-z10.1007/s11666-016-0402-z ↗
16. G. Sundararajan, N.M. Chavan and S. Kumar, The Elastic Modulus of Cold Spray Coatings: Influence of Inter-Splat Boundary Cracking, J. Therm. Spray Technol., 2014, 22, p 1348-1357. https://doi.org/10.1007/s11666-013-0024-510.1007/s11666-013-0024-5 ↗
17. B. Al-Mangour, R. Mongrain, E. Irissou and S. Yue, Improving the Strength and Corrosion Resistance of 316L Stainless Steel for Biomedical Applications using Cold Spray, Surf. Coat. Technol., 2013, 216, p 297-307. https://doi.org/10.1016/j.surfcoat.2012.11.06110.1016/j.surfcoat.2012.11.061 ↗
18. S. Yin, J. Cizek, X. Yan and R. Lupoi, Annealing Strategies for Enhancing Mechanical Properties of Additively Manufactured 316L Stainless Steel Deposited by Cold Spray, Surf. and Coat. Technol., 2019, 370, p 353-361. https://doi.org/10.1016/j.surfcoat.2019.04.01210.1016/j.surfcoat.2019.04.012 ↗
19. S. Bagherifard, J. Kondas, S. Monti, J. Cizek, F. Perego, O. Kovarik, F. Lukac, F. Gaertner and M. Guagliano, Tailoring Cold Spray Additive Manufacturing of Steel 316L for Static and Cyclic Load-Bearing Applications, Mater. & Des., 2021, 203, p 109575. https://doi.org/10.1016/j.matdes.2021.10957510.1016/j.matdes.2021.109575 ↗
20. T. Stoltenhoff, C. Borchers, F. Gärtner and H. Kreye, Microstructures and Key Properties of Cold-Sprayed and Thermally Sprayed Copper Coatings, Surf. Coat. Technol., 2006, 200(16-17), p 4947-4960. https://doi.org/10.1016/j.s.2005.05.01110.1016/j.s.2005.05.011 ↗
21. D. Peckner and I.M. Bernstein, Handbook of Stainless Steels, 1st ed. McGraw-Hill, New York, 1977.
22. N. Parvathavarthini, R. Dayal, H. Khatak, V. Shankar and V. Shanmugam, Sensitization Behavior of Modified 316N and 316L Stainless Steel Weld Metals After Complex Annealing and Stress Relieving Cycles, J. Nucl. Mater., 2006, 355, p 68-82. https://doi.org/10.1016/j.jnucmat.2006.04.00610.1016/j.jnucmat.2006.04.006 ↗
23. M.X. Zhang, B. Yang, S.L. Wang and H.C. Wu, Mechanisms of Thermo-Mechanical Process on Grain Boundary Character Distribution of 316L Austenitic Stainless Steel, Mater. Sci. Forum, 2016, 850, p 965-970. https://doi.org/10.4028/www.scientific.net/MSF.850.96510.4028/www.scientific.net/MSF.850.965 ↗
24. M. Naghizadeh and H. Mirzadeh, Microstructural Evolutions during Reversion Annealing of Cold-Rolled AISI 316 Austenitic Stainless Steel, Metall. Mater. Trans. A, 2018, 49, p 2248-2256. https://doi.org/10.1007/s11661-018-4583-610.1007/s11661-018-4583-6 ↗
25. F. Bertaut, Signification de la Dimension Crystalline Mesurée d’après la Largeur de raie Debye-Scherrer, Comptes-Rendus Hebdomadaires des Séances de l’Académie des Sciences., 1948, 228, p 187-189. (in French)
26. W.Y. Li, H. Liao, C.J. Li, H.S. Bang and C. Coddet, Numerical Simulation of Deformation Behavior of Al Particles Impacting on Al Substrate and Effect of Surface Oxide Films on Interfacial Bonding in Cold Spraying, Appl. Surf. Sci., 2007, 253, p 5048-5091. https://doi.org/10.1016/2006.11.02010.1016/2006.11.020 ↗
27. S. Guetta, M.-H. Berger, F. Borit, V. Guipont, M. Jeandin, M. Boustie, Y. Ichikawa, K. Sakaguchi and K. Ogawa, Influence of Particle Velocity on Adhesion of Cold-Sprayed Splats, J. Therm. Spray Technol., 2009, 18, p 331-342. https://doi.org/10.1007/s11666-009-9327-010.1007/s11666-009-9327-0 ↗
28. M. Grujicic, C. Zhao, W. DeRosset and D. Helfritch, Adiabatic Shear Instability based Mechanism for Particles/Substrates Bonding in the Cold-Gas Dynamic Process, Mater. Des., 2004, 25, p 681-688. https://doi.org/10.1016/j.matdes.2004.03.00810.1016/j.matdes.2004.03.008 ↗
29. W.-Y. Li and W. Gao, Some Aspects on 3D Numerical Modeling of High Velocity Impact of Particles In Cold Spraying by Explicit Finite Element Analysis, Appl. Surf. Sci., 2009, 255, p 7878-7892. https://doi.org/10.1016/j.apsusc.2009.04.13510.1016/j.apsusc.2009.04.135 ↗
30. Y. Ichikawa, R. Tokoro, M. Tanno and K. Ogawa, Elucidation of Cold-Spray Deposition Mechanism by Auger Elctron Spectroscopic Evaluation of Bonding Interface Oxide Film, Acta Mater., 2019, 164, p 39-49. https://doi.org/10.1016/j.actamat.2018.09.04110.1016/j.actamat.2018.09.041 ↗
31. P. Deng, M. Karadge, R.B. Rebak, V.K. Gupta, B.C. Prorok and X. Lou, The Origin and Formation of Oxygen Inclusions in Austenitic Stainless Steels Manufactured by Laser Powder Bed Fusion, Addit. Manuf., 2020, 35, p 101334.
32. X. Yang, F. Tang, X. Hao and Z. Li, Oxide Evolution During the Solidification od 316L Stainless Steel from Additive Manufacturing Powders with Different Oxygen Contents, Metall. Mater. Trans. B, 2021 https://doi.org/10.1007/s11663-021-02191-w10.1007/s11663-021-02191-w ↗
33. D. Riabov, M. Rashidi, E. Hryha and S. Bengtsson, Effect of the Powder Feedstock on the Oxide Dispersion Strengthening of 316L Stainless Steel Produced by Laser Powder Bed Fusion, Mater. Charact., 2020, 169, p 110582. https://doi.org/10.1016/j.matchar.2020.11058210.1016/j.matchar.2020.110582 ↗
34. T. Voisin, J.B. Forien, A. Perron, S. Aubry, N. Bertin, A. Samanta, A. Baker and Y.M. Wang, New Insights on Cellular Structures Strengthening Mechanisms and Thermal Stability of an Austenitic Stainless Steel Fabricated by Laser Powder Bed Fusion, Acta Mater, 2021, 203, p 116476. https://doi.org/10.1016/j.actamat.2020.11.01810.1016/j.actamat.2020.11.018 ↗
35. X. Zhou, Z. An, Z. Shen, W. Liu and C. Yao, Particles Control in Selective Laser Melting in situ Oxide Dispersion Strengthened Method, IOP Conf. Series: Materials Sci. Eng., 2017 https://doi.org/10.1088/1757-899X/167/1/01204810.1088/1757-899X/167/1/012048 ↗
36. F.J. Humphreys, M. Hatherly, A. Rollett, G. S. Rohrer, Recrystallization and Related Annealing Phenomena, 2nd ed., Elsevier. (2004)10.1016/B978-008044164-1/50016-5 ↗
37. M.F. McGuire, Stainless Steels for Design Engineers, ASM International. (2008)10.31399/asm.tb.ssde.9781627082860 ↗