journal article·2025-10Open access

Coating Characteristics of Plasma-Sprayed Ceramic Thermal Barrier Coatings on Internal Diameter (ID) Surfaces

Maheshwar Rao Bagathi, Robert Vaßen, Olivier Guillon, Georg Mauer

Abstract

Abstract Thermal barrier coatings (TBCs) are essential for insulating and protecting components in high-temperature environments, with applications traditionally focused on external surfaces. However, the development of TBCs for internal diameters (ID), particularly for small bores below 200 mm, poses significant challenges due to the limited understanding of coating formation mechanisms in confined geometries and the constraints of process conditions. Therefore, this study aims to elucidate the characteristics of plasma-sprayed ceramic TBCs on ID surfaces, with the goal of establishing a relationship between process parameters, microstructure, and coating properties for 8 wt.% yttria-stabilized zirconia (8YSZ) topcoats applied via atmospheric plasma spraying (APS) using the SM-F100 CONNEX ID torch. The key APS parameters, namely the hydrogen flow rate, current, and spray distance, were investigated using a design of experiments (DOE) methodology to systematically study both the individual and interactive effects of these parameters on coating systems such as porosity and deposition efficiency, which are critical features of TBC performance. Since ID coatings are constrained by limited space for spray distance and torch placement inside the tubular component, the selection of the appropriate feedstock becomes challenging. Therefore, feedstocks with different morphologies and sizes were investigated and evaluated based on the resulting porosity and deposition efficiency. An agglomerated and sintered 8YSZ feedstock showed the most promising results. In addition, this study also examined the impact of substrate geometry (flat versus curved surfaces) on coating properties and process control. The results contribute to the broader scientific understanding of plasma spray technology for internal diameter (ID) surfaces.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: High-Temperature Coating Behaviors · Advanced ceramic materials synthesis · Nuclear Materials and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (41)

Show source-provided references
1. N.P. Padture, M. Gell, and E.H. Jordan, Thermal Barrier Coatings for Gas-Turbine Engine Applications, Science (1979), 2002, 296(5566), p 280-284.10.1126/science.1068609 ↗
2. D. Stöver and C. Funke, Directions of the Development of Thermal Barrier Coatings in Energy Applications, J. Mater. Process. Technol., 1999, 92-93, p 195–202.10.1016/S0924-0136(99)00244-7 ↗
3. J. Smith, J. Scheibel, D. Classen, S. Paschke, S. Elbel, K. Fick, and D. Carlson, Thermal Barrier Coating Validation Testing for Industrial Gas Turbine Combustion Hardware, J. Eng. Gas Turbines Power, 2016 https://doi.org/10.1115/1.403144810.1115/1.4031448 ↗
4. R. Darolia, Thermal Barrier Coatings Technology: Critical Review, Progress Update, Remaining Challenges and Prospects, Int. Mater. Rev., 2013, 58(6), p 315-348.10.1179/1743280413Y.0000000019 ↗
5. D.P.H. Hasselman, L.F. Johnson, L.D. Bentsen, R. Syed, H.L. Lee, and M.V. Swain, Thermal Diffusivity and Conductivity of Dense Polycrystalline ZrO2 Ceramics: A Survey, Am. Ceram. Soc. Bull., 1987, 66(5), p 799-806.
6. J. Gutleber and J. Tewes, “Neuartige HVOF-Technologie für das Beschichten kleiner Innendurchmesser [Novel HVOF Technology for Small ID Spraying),” Conference proceedings, (Erding), Gemeinschaft Thermisches Spritzen e.V. (GTS), Unterschleißheim, Deutschland, 2018, p 123-132.
7. W. Tillmann, C. Schaak, L. Hagen, G. Mauer, and G. Matthäus, Internal Diameter Coating Processes for Bond Coat (HVOF) and Thermal Barrier Coating (APS) Systems, J. Therm. Spray Technol., 2019, 28(1–2), p 233-241.10.1007/s11666-018-0781-4 ↗
8. C.R.C. Lima and J.M. Guilemany, Adhesion Improvements of Thermal Barrier Coatings with HVOF Thermally Sprayed Bond Coats, Surf. Coat. Technol., 2007, 201(8), p 4694-4701.10.1016/j.surfcoat.2006.10.005 ↗
9. C. Wales, M. Tierney, M. Pavier, and P.EJ. Flewitt, Reducing Steam Transport Pipe Temperatures in Power Plants, Energy, 2019, 183, p 127-141.10.1016/j.energy.2019.06.059 ↗
10. P.W.J. Marion, O. Drenik, C. Frappart, F. Kluger, M. Sell, A. Skea, and R. Vanstonee, “Advanced Ultrasupercritical Steam Power Plants”, 1st IEA Clean Coal Centre Workshop on Advanced Ultra-Supercritical Coal-Fired Power Plants, Austria, Vienna, 2012.
11. G.R. Holcomb, J. Tylczak, and R. Hu, Materials Performance in USC Steam Portland (No. NETL-PUB-195). National Energy Technology Lab. (NETL), Pittsburgh, PA, and Morgantown, WV (United States). In-house Research, 2011.
12. X. Guo, W. Sun, A. Becker, A. Morris, M. Pavier, P. Flewitt, M. Tierney, and C. Wales, Thermal and Stress Analyses of a Novel Coated Steam Dual Pipe System for Use in Advanced Ultra-Supercritical Power Plant, Int. J. Pressure Vessels Piping, 2019, 176.10.1016/j.ijpvp.2019.103933 ↗
13. M. Ekström, A. Thibblin, A. Tjernberg, C. Blomqvist, and S. Jonsson, Evaluation of Internal Thermal Barrier Coatings for Exhaust Manifolds, Surf. Coat. Technol., 2015, 272, p 198-212.10.1016/j.surfcoat.2015.04.005 ↗
14. H. Kosaka, Y. Wakisaka, Y. Nomura, Y. Hotta, M. Koike, K. Nakakita, and A. Kawaguchi, Concept of “temperature swing heat insulation” in Combustion Chamber Walls, and Appropriate Thermo-Physical Properties for Heat Insulation Coat, SAE Int. J. Engines, 2013, 6(1), p 142-149.10.4271/2013-01-0274 ↗
15. A. Babu, G. Koutsakis, S. Kokjohn, and M. Andrie, Experimental and analytical study of temperature swing piston coatings in a medium-duty diesel engine. SAE International J. Adv. Curr. Pract. Mob., (2022-01-0442), 2022, p 235-248.10.4271/2022-01-0442 ↗
16. J. Somhorst, W.U. De Goes, M. Oevermann, and M. Bovo, Experimental evaluation of novel thermal barrier coatings in a single cylinder light duty diesel engine (No. 2019-24-0062). SAE Technical Paper, 2019.10.4271/2019-24-0062 ↗
17. G. Koutsakis, S. Miles, and J. Ghandhi, Assessment of in-cylinder thermal barrier coatings over a full vehicle drive cycle (No. 2021-01-0456). SAE Technical Paper, 2021.10.4271/2021-01-0456 ↗
18. M. Andrie, S. Kokjohn, S. Paliwal, L. S. Kamo, A. Kamo, and D. Procknow, Low heat capacitance thermal barrier coatings for internal combustion engines (No. 2019-01-0228). SAE Technical Paper, 2019.10.4271/2019-01-0228 ↗
19. A. Kawaguchi, H. Iguma, H. Yamashita, N. Takada et al., Thermo-Swing Wall Insulation Technology; - A Novel Heat Loss Reduction Approach on Engine Combustion Chamber (No. 2016-01-2333). SAE Technical Paper, 2016.10.4271/2016-01-2333 ↗
20. N. Uchida, A Review of Thermal Barrier Coatings for Improvement in Thermal Efficiency of Both Gasoline and Diesel Reciprocating Engines, Int. J. Engine Res., 2022, p 3-19.10.1177/1468087420978016 ↗
21. C.J. James, Analysis of Parasitic Losses in Heavy Duty Diesel Engines. Diss. Massachusetts Institute of Technology, 2012.
22. R. Vaßen, M.O. Jarligo, T. Steinke, D.E. Mack, and D. Stöver, Overview on advanced thermal barrier coatings, Surf. Coat. Technol., 2010, 205(4), p 938-942.10.1016/j.surfcoat.2010.08.151 ↗
23. S. Bose, Thermal barrier coatings (TBCs), In High Temperature Coatings; Elsevier: Amsterdam, 2007, p 155-232.10.1016/B978-075068252-7/50008-1 ↗
24. M. Mutter, G. Mauer, R. Mücke, O. Guillon, and R. Vaßen, Systematic Investigation on the Influence of Spray Parameters on the Mechanical Properties of Atmospheric Plasma-Sprayed YSZ Coatings, J. Therm. Spray Technol., 2018, 27(4), p 566-580.10.1007/s11666-018-0697-z ↗
25. A. Kulkarni, A. Vaidya, A. Goland, S. Sampath, and H. Herman, Processing Effects on Porosity-Property Correlations in Plasma Sprayed Yttria-Stabilized Zirconia Coatings, Mater. Sci. Eng. A, 2003, 359(1-2), p 100-111.10.1016/S0921-5093(03)00342-3 ↗
26. G. Mauer, R. Vaßen and D. Stöver, Comparison and Applications of DPV-2000 and Accuraspray-G3 Diagnostic Systems, J. Therm. Spray Technol., 2007. https://doi.org/10.1007/s11666-007-9047-210.1007/s11666-007-9047-2 ↗
27. J. Antony, Design of Experiments for Engineers and Scientists, 2nd ed. Elsevier, London, 2014.
28. R. Vaßen, E. Bakan, and S. Schwartz-Lückge, Influence of Substrate Removal Method on the Properties of Free-Standing YSZ Coatings, Coatings, MDPI AG, 2021, 11(4).10.3390/coatings11040449 ↗
29. J. Matejicek and S. Sampath, In Situ Measurement of Residual Stresses and Elastic Moduli in Thermal Sprayed Coatings Part 1: Apparatus and Analysis, Acta Mater., 2003, 51(3), p 863-872.10.1016/S1359-6454(02)00478-0 ↗
30. I. Baumann, W. Tillmann, C. Schaak, K. Schmidt, L. Hagen, J. Zajaczkowski, G. Schmidtmann, G. Matthäus, and W. Luo, Internal Diameter Coating by Warm Spraying of fine WC-12Co Powders (− 10 + 2 mm) with Very Short Spray Distances up to 10 mm, J. Therm. Spray Technol., 2021, 30(5), p 1344-1364.10.1007/s11666-021-01195-x ↗
31. A. Nouri and A. Sola, Powder Morphology in Thermal Spraying, J. Adv. Manuf. Process., 2019, 1(3), e10020.10.1002/amp2.10020 ↗
32. P. Fauchais, G. Montavon, and G. Bertrand, From Powders to Thermally Sprayed Coatings, J. Therm. Spray Technol., 2010, 19(1-2), p 56-80.10.1007/s11666-009-9435-x ↗
33. A. T.J. Verbeek, “Plasma sprayed thermal barrier coatings: production, characterization and testing,” Phd Thesis 1 (Research TU/e / Graduation TU/e), Mechanical Engineering, Technische Universiteit Eindhoven, 1992.
34. E. Pfender, Heat and Momentum Transfer to Particles in Thermal Plasma Flows, Pure Appl. Chem., 1985, 57(9), p 1179-1195.10.1351/pac198557091179 ↗
35. M.I. Boulos, P.L. Fauchais, and J.V.R. Heberlein, Thermal Spray Fundamentals: From Powder to Part, Springer, New York, 2021.10.1007/978-3-030-70672-2 ↗
36. M. Vardelle, A. Vardelle, and P. Fauchais, Spray Parameters and Particle Behavior Relationships During Plasma Spraying, J. Therm. Spray Technol., 1993, 2(1), p 79-91.10.1007/BF02647426 ↗
37. G. Mauer, R. Vaßen, and D. Stöver, Atmospheric Plasma Spraying of Yttria-Stabilized Zirconia Coatings with Specific Porosity, Surf. Coat. Technol., 2009, 204(1-2), p 172-179.10.1016/j.surfcoat.2009.07.017 ↗
38. J. Medřický, N. Curry, Z. Pala, M. Vilemova, T. Chraska, J. Johansson, and N. Markocsan, Optimization of High Porosity Thermal Barrier Coatings Generated with a Porosity Former, J. Therm. Spray Technol., 2015, 24(4), p 622-628.10.1007/s11666-014-0214-y ↗
39. V. Teixeira, M. Andritschky, W. Fischer, H.P. Buchkremer, and D. Stöver, Effects of Deposition Temperature and Thermal Cycling on Residual Stress State in Zirconia-Based Thermal Barrier Coatings, Surf. Coat. Technol., 1999, 120-121, p 103-111.10.1016/S0257-8972(99)00341-2 ↗
40. V. Lasseur, S. Goutier, V. MartinezGarcia, A. Denoirjean, E. Meillot, G. Mariaux, J. Absi, and A. Killinger, Residual Stress Evolution in Zirconia (Y8%) Coatings During Atmospheric Plasma Spraying for Substrates Under Rotating Kinematic, J. Therm. Spray Technol., 2020, 29(6), p 1313-1321.10.1007/s11666-020-01070-1 ↗
41. S. Kuroda, T. Dendo, and S. Kitahara, Quenching Stress in Plasma Sprayed Coatings and Its Correlation with the Deposit Microstructure, J. Therm. Spray Technol., 1995, 4(1), p 75-84.10.1007/BF02648531 ↗