Effect of Residual Stress on the Wear Resistance of Thermal Spray Coatings
Source abstract
Abstract
The wear resistance of thermal spray coatings mainly depends on coating properties such as the microstructure, hardness, and porosity, as well as on the residual stress in the coating. The residual stress is induced by a variety of influences e.g., temperature gradients, difference of the thermal expansion coefficient of the coating/substrate materials, and the geometry of the components. To investigate the residual stress, the impulse excitation technique was employed to measure the Young’s and shear moduli. The residual stress was determined by the hole-drilling method and x-ray diffraction. Pin-on-Disk and Pin-on-Tube tests were used to investigate the wear behavior. After the wear tests, the wear volume was measured by means of a 3D-profilometer. The results show that the value of the residual stress can be modified by varying the coating thickness and the substrate geometry. The compressive stress in the HVOF-sprayed WC-Co coatings has a significant positive influence on the wear resistance whereas the tensile stress has a negative effect.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: High-Temperature Coating Behaviors · Advanced materials and composites · Metal Alloys Wear and Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (35)
Show source-provided references
1. H. Chen, Y. Zhang, and C. Ding, Tribological Properties of Nanostructured Zirconia Coatings Deposited by Plasma Spraying, Wear, 2002, 253(7-8), p 885-89310.1016/S0043-1648(02)00221-1 ↗
2. G. Sundararajan, K.U. Prasad, D.S. Rao, and S.V. Joshi, A Comparative Study of Tribological Behavior of Plasma and D-Gun Sprayed Coatings Under Different Wear Modes, J. Mater. Eng. Perform., 1998, 7(3), p 343-35110.1361/105994998770347783 ↗
3. W. Tillmann, I. Baumann, P.S. Hollingsworth, and L. Hagen, Sliding and Rolling Wear Behavior of HVOF-Sprayed Coatings Derived from Conventional, Fine and Nanostructured WC-12Co Powders, J. Therm. Spray Technol., 2014, 23(1-2), p 262-28010.1007/s11666-013-0038-1 ↗
4. S.F. Wayne, S. Sampath, and V. Anand, Wear Mechanisms in Thermally-Sprayed Mo-Based Coatings, Tribol. Trans., 2008, 37(3), p 636-64010.1080/10402009408983340 ↗
5. F.-W. Bach, K. Möhwald, B. Drößler, and L. Engl, Technik und Potenziale des Verschleißschutzes Mittels Thermisch Gespritzter Beschichtungen, Mat.-wiss. u. Werkstofftech., 2005, 36(8), p 353-359 (in German)10.1002/mawe.200500892 ↗
6. H. Liao, B. Normand, and C. Coddet, Influence of Coating Microstructure on the Abrasive Wear Resistance of WC/Co Cermet Coatings, Surf. Coat. Technol., 2000, 124(2-3), p 235-24210.1016/S0257-8972(99)00653-2 ↗
7. D. Stewart, P. Shipway, and D. McCartney, Influence of Heat Treatment on the Abrasive Wear Behaviour of HVOF Sprayed WC-Co Coatings, Surf. Coat. Technol., 1998, 105(1-2), p 13-2410.1016/S0257-8972(98)00444-7 ↗
8. S. Takeuchi, M. Ito, and K. Takeda, Modelling of Residual Stress in Plasma-Sprayed Coatings: Effect of Substrate Temperature, Surf. Coat. Technol., 1990, 43-44, p 426-43510.1016/0257-8972(90)90094-S ↗
9. L. Pawlowski, The Science and Engineering of Thermal Spray Coatings, Wiley, New York, 200810.1002/9780470754085 ↗
10. S. Sampath, X. Jiang, J. Matejicek, L. Prchlik, A. Kulkarni, and A. Vaidya, Role of Thermal Spray Processing Method on the Microstructure, Residual Stress and Properties of Coatings: An Integrated Study For Ni-5 wt.%Al Bond Coats, Mater. Sci. Eng. A, 2004, 364(1-2), p 216-23110.1016/j.msea.2003.08.023 ↗
11. Y.C. Tsui and T.W. Clyne, An Analytical Model for Predicting Residual Stresses in Progressively Deposited Coatings Part 1: Planar Geometry, Thin Solid Films, 1997, 306(1), p 23-3310.1016/S0040-6090(97)00199-5 ↗
12. S. Kuroda and T.W. Clyne, The Quenching Stress in Thermally Sprayed Coatings, Thin Solid Films, 1991, 200(1), p 49-6610.1016/0040-6090(91)90029-W ↗
13. S. Kuroda, T. Fukushima, and S. Kitahara, Significance of Quenching Stress in the Cohesion and Adhesion of Thermally Sprayed Coatings, J. Therm. Spray Technol., 1992, 1(4), p 325-33210.1007/BF02647160 ↗
14. P. Bansal, P.H. Shipway, and S.B. Leen, Effect of Particle Impact on Residual Stress Development in HVOF Sprayed Coatings, J. Therm. Spray Technol., 2006, 15(4), p 570-57510.1361/105996306X146703 ↗
15. S. Kuroda, Ed., Properties and Characterization of Thermal Sprayed Coatings—A Review of Recent Research Progress. Proceedings of the 15th International Thermal Spray Conference 25-29 May, 1998.10.31399/asm.cp.itsc1998p0539 ↗
16. J. Stokes and L. Looney, Residual Stress in HVOF Thermally Sprayed Thick Deposits, Surf. Coat. Technol., 2004, 177-178, p 18-2310.1016/j.surfcoat.2003.06.003 ↗
17. M. Wenzelburger, D. López, and R. Gadow, Methods and Application of Residual Stress Analysis on Thermally Sprayed Coatings and Layer Composites, Surf. Coat. Technol., 2006, 201(5), p 1995-200110.1016/j.surfcoat.2006.04.040 ↗
18. T.W. Clyne and S.C. Gill, Residual Stresses in Thermal Spray Coatings and Their Effect on Interfacial Adhesion: a Review of Recent Work, J. Therm. Spray Technol., 1996, 5(4), p 401-41810.1007/BF02645271 ↗
19. R. Gadow, M.J. Riegert-Escribano, and M. Buchmann, Residual Stress Analysis in Thermally Sprayed Layer Composites, Using the Hole Milling and Drilling Method, J. Therm. Spray Technol., 2005, 14(1), p 100-10810.1361/10599630522756 ↗
20. M. Wenzelburger, M. Escribano, and R. Gadow, Modeling of Thermally Sprayed Coatings on Light Metal Substrates: Layer Growth and Residual Stress Formation, Surf. Coat. Technol., 2004, 180-181, p 429-43510.1016/j.surfcoat.2003.10.125 ↗
21. Y.Y. Santana, P.O. Renault, M. Sebastiani, J.G. La Barbera, J. Lesage, E. Bemporad, E. Le Bourhis, E.S. Puchi-Cabrera, and M.H. Staia, Characterization and Residual Stresses of WC-Co Thermally Sprayed Coatings, Surf. Coat. Technol., 2008, 202(18), p 4560-456510.1016/j.surfcoat.2008.04.042 ↗
22. W. Tillmann, W. Luo, I. Baumann, P. Hollingsworth, B. Krebs, and L. Hagen, Optimization of Thermal Spray Coatings For Forming Tools, Zhingguo Biaomian Gongcheng (China Surface Engineering), 2012, 25(4), p 1-14 (in Chinese)
23. I. Baumann, Highly Wear-Resistant and Near-Net-Shape Tool Surfaces by Means of High Velocity Oxygen Fuel Flame Spraying Techniques, 5th ed., Vulkan-Verlag, Essen, 2012
24. D. Biermann, S. Goeke, W. Tillmann, and J. Nebel, Improvement of Wear Resistant Thermally Sprayed Coatings by Microfinishing, CIRP Ann. Manuf. Technol., 2013, 62(1), p 559-56210.1016/j.cirp.2013.03.023 ↗
25. S. Goeke, D. Biermann, D. Stickel, P. Stemmer, A. Fischer, K. Geenen, S. Huth, and W. Theisen, Enhancing the Surface Integrity of Tribologically Stressed Contacting Surfaces by an Adjusted Surface Topography, Procedia CIRP, 2014, 13, p 214-21810.1016/j.procir.2014.04.037 ↗
26. F. Haase, “Eigenspannungsermittlung an dünnwandigen Bauteilen und Schichtverbunden”, Dissertation, Universität Dortmund, 1998 (in German).
27. I.C. Noyan and J.B. Cohen, Residual Stress, Springer Verlag, New York, 198710.1007/978-1-4613-9570-6 ↗
28. V. Hauk, Structural and Residual Stress Analysis by Nondestructive Methods: Evaluation-Application-Assessment, Elsevier, Amsterdam, 1997
29. B. Eigenmann and E. Macherauch, Röntgenographische Untersuchung von Spannungszuständen in Werkstoffen. Teil 2, Mat.-wiss. u. Werkstofftech., 1995, 26(4), p 199-216 (in German).10.1002/mawe.19950260410 ↗
30. W. Tillmann, U. Selvadurai, and W. Luo, Measurement of the Young’s Modulus of Thermal Spray Coatings by Means of Several Methods, J. Therm. Spray Technol., 2013, 22(2-3), p 290-29810.1007/s11666-012-9855-x ↗
31. German Institute for Standardization, “Hochleistungskeramik-Mechanische Eigenschaften Monolithischer Keramik bei Raumtemperatur” (High Performance Ceramic—Mechanical Properties of Monolithic Ceramics at Room Temperature), DIN EN 843-2, German Institute for Standardization.
32. U. Selvadurai, P. Hollingsworth, I. Baumann, B. Hussong, W. Tillmann, S. Rausch, and D. Biermann, Influence of the Handling Parameters on Residual Stresses of HVOF-Sprayed WC-12Co Coatings, Surf. Coat. Technol., 2015, 268, p 30-3510.1016/j.surfcoat.2014.11.055 ↗
33. W. Luo, W. Tillmann, and U. Selvadurai, In Situ Wear Test on Thermal Spray Coatings in a Large Chamber Scanning Electron Microscope, J. Therm. Spray Technol., 2015, 24(1-2), p 263-270
34. W. Tillmann, W. Luo, and U. Selvadurai, Wear Analysis of Thermal Spray Coatings on 3D Surfaces, J. Therm. Spray Technol., 2014, 23(1-2), p 245-25110.1007/s11666-013-9983-y ↗
35. W. Tillmann, B. Hussong, T. Priggemeier, S. Kuhnt, N. Rudak, and H. Weinert, Influence of Parameter Variations on WC-Co Splat Formation in an HVOF Process Using a New Beam-Shutter Device, J. Therm. Spray Technol., 2013, 22(2-3), p 250-26210.1007/s11666-012-9881-8 ↗