Assessing Process and Coating Reliability Through Monitoring of Process and Design Relevant Coating Properties
Source abstract
Abstract
Thermal spray in general, plasma spray in particular, is a highly complex process with numerous interacting variables associated with generation of the spray stream, deposit formation dynamics, and the resultant property linkages. Compounding this variability further are both the spatial (different booths and different locations) and temporal (process start-stops, hardware degradation, operator etc.) effects. As such, an understanding of process and coating consistency and variability offers significant challenges. Recent scientific advances as well as measurement tools have enabled elucidation of the intrinsic variabilities associated with each of the process sub-steps; however, integrated understanding of the system level reliability is still lacking. This article seeks an integrated assessment of process and coating reliability through systematic measurements of variabilities during each stage of the process subjected to different operating parameters. Through critical examination of first-order process maps, the influence of process parameters on particle state is reviewed for repeated spray runs with a single parameter effect as well as across a spectrum of process parameters. In addition, influence of these changes on design-relevant coating properties were obtained for plasma-sprayed zirconia through recourse to novel in situ and ex situ substrate curvature measurements. Finally, the implications of such integrated reliability studies have been explored through collaborative experiments conducted in the industrial sites.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: High-Temperature Coating Behaviors · Nuclear Materials and Properties · Advanced ceramic materials synthesis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (41)
Show source-provided references
1. V. Arnault, R. Mevrel, S. Alperine, and Y. Jaslier, Thermal Barrier Coatings for Aircraft Turbine Airfoils: Thermal Challenge and Materials, Rev. Metall. Cah. Inf. Tech., 1999, 96(5), p 585-597
2. P. Fauchais, Formation of Plasma-Sprayed Coatings, J. Therm. Spray Technol., 1995, 4(1), p 3-610.1007/BF02648521 ↗
3. P. Fauchais, A. Grimaud, A. Vardelle, and M. Vardelle, Plasma Spraying: An Overview, Ann. Phys., 1989, 14(3), p 261-310 (in French)10.1051/anphys:01989001403026100 ↗
4. P. Fauchais, Understanding Plasma Spraying, J. Phys. D: Appl. Phys., 2004, 37(9), p R86-R10810.1088/0022-3727/37/9/R02 ↗
5. S. Sampath and R. McCune, Thermal-Spray Processing of Materials, MRS Bull., 2000, 25(7), p 12-1410.1557/mrs2000.117 ↗
6. S. Ben Naoua, M. El Ganaoui, H. Sammouda, and P. Fauchais, Rapid Solidefication Study of Stabilized Zirconia Under Plasma Spraying, High Temp. Mater. Processes, 2006, 10(2), p 185-19610.1615/HighTempMatProc.v10.i2.20 ↗
7. S. Sampath and H. Herman, Rapid Solidification and Microstructure Development During Plasma Spray Deposition, J. Therm. Spray Technol., 1996, 5(4), p 445-45610.1007/BF02645275 ↗
8. P. Bengtsson and T. Johannesson, Characterization of Microstructural Defects in Plasma-Sprayed Thermal Barrier Coatings, J. Therm. Spray Technol., 1995, 4(3), p 245-25110.1007/BF02646967 ↗
9. S. Alperine and L. Lelait, Microstructural Investigations of Plasma-Sprayed Yttria Partially-Stabilized Zirconia Tbc (in Relation to Thermomechanical Resistance and High-Temperature Oxidation Mechanisms), J. Eng. Gas Turbines Power, 1994, 116(1), p 258-26510.1115/1.2906802 ↗
10. A.J. Allen, G.G. Long, H. Boukari, J. Ilavskya, A. Kulkarni, S. Sampath, H. Herman, and A.N. Goland, Microstructural Characterization Studies to Relate the Properties of Thermal-Spray Coatings to Feedstock and Spray Conditions, Surf. Coat. Technol., 2001, 146, p 544-55210.1016/S0257-8972(01)01433-5 ↗
11. D.R. Clarke and C.G. Levi, Materials Design for the Next Generation Thermal Barrier Coatings, Annu. Rev. Mater. Res., 2003, 33, p 383-41710.1146/annurev.matsci.33.011403.113718 ↗
12. C. Moreau, J.F. Bisson, R.S. Lima, and B.R. Marple, Diagnostics for Advanced Materials Processing by Plasma Spraying, Pure Appl. Chem., 2005, 77(2), p 443-46210.1351/pac200577020443 ↗
13. J.R. Fincke, D.C. Haggard, and W.D. Swank, Particle Temperature Measurement in the Thermal Spray Process, J. Therm. Spray Technol., 2001, 10(2), p 255-26610.1361/105996301770349358 ↗
14. P.F.M. Vardelle, Plasma Spray Processes: Diagnostics and Control?, Pure Appl. Chem., 1994, 5(3), p 205-212
15. C. Moreau and L. Leblanc, Optimization and Process Control for High Performance Thermal Spray Coatings, Durable Surf., 2001, 197, p 27-57
16. V. Srinivasan, M. Friis, A. Vaidya, T. Streibl, and S. Sampath, Particle Injection in Direct Current Air Plasma Spray: Salient Observations and Optimization Strategies, Plasma Chem. Plasma Process., 2007, 27(5), p 609-62310.1007/s11090-007-9089-8 ↗
17. V. Srinivasan, A. Vaidya, T. Streibl, M. Friis, and S. Sampath, On the Reproducibility of Air Plasma Spray Process and Control of Particle State, J. Therm. Spray Technol., 2006, 15(4), p 739-74310.1361/105996306X147199 ↗
18. S. Sampath, V. Srinivasan, A. Valarezo, A. Vaidya, and T. Streibl, Sensing, Control, and In Situ Measurement of Coating Properties: An Integrated Approach Toward Establishing Process-Property Correlations, J. Therm. Spray Technol., 2009, 18(2), p 243-25510.1007/s11666-009-9314-5 ↗
19. V. Srinivasan, “A Critical Assessment of In-Flight Particle State During Plasma Spraying of YSZ and its Implications on Coating Properties and Process Reliability,” Ph.D. Thesis, Stony Brook University, 2007
20. A. Vaidya, V. Sirinivasan, T. Streibl, M. Friis, W. Chi, and S. Sampath, Process Maps for Plasma Spraying of Yttria-Stabilized Zirconia: An Integrated Approach to Design, Optimization and Reliability, Mater. Sci. Eng. A, 2008, 497(1-2), p 239-25310.1016/j.msea.2008.07.058 ↗
21. A.A. Kulkarni, A. Goland, H. Herman, A.J. Allen, J. Ilavsky, G.G. Long, and F. De Carlo, Advanced Microstructural Characterization of Plasma-Sprayed Zirconia Coatings Over Extended Length Scales, J. Therm. Spray Technol., 2005, 14(2), p 239-25010.1361/10599630523818 ↗
22. H. Wang and R.B. Dinwiddie, Characterization of Thermal Barrier Coatings Using Thermal Methods, Adv. Eng. Mater., 2001, 3(7), p 465-46810.1002/1527-2648(200107)3:7<465::AID-ADEM465>3.0.CO;2-G ↗
23. F. Tang and J.M. Schoenung, Evolution of Young’s Modulus of Air Plasma Sprayed Yttria-Stabilized Zirconia in Thermally Cycled Thermal Barrier Coatings, Scripta Mater., 2006, 54(9), p 1587-159210.1016/j.scriptamat.2006.01.021 ↗
24. A. Kucuk, C.C. Berndt, U. Senturk, R.S. Lima, and C.R.C. Lima, Influence of Plasma Spray Parameters on Mechanical Properties of Yttria Stabilized Zirconia Coatings. I: Four Point Bend Test, Mater. Sci. Eng. A, 2000, 284(1-2), p 29-4010.1016/S0921-5093(00)00799-1 ↗
25. A. Kucuk, C.C. Berndt, U. Senturk, and R.S. Lima, Influence of Plasma Spray Parameters on Mechanical Properties of Yttria Stabilized Zirconia Coatings. II: Acoustic Emission Response, Mater. Sci. Eng. A, 2000, 284(1-2), p 41-5010.1016/S0921-5093(00)00800-5 ↗
26. T. Nakamura and Y.J. Liu, Determination of Nonlinear Properties of Thermal Sprayed Ceramic Coatings Via Inverse Analysis, Int. J. Solids Struct., 2007, 44(6), p 1990-200910.1016/j.ijsolstr.2006.08.012 ↗
27. Y. Liu, T. Nakamura, V. Srinivasan, A. Vaidya, A. Gouldstone, and S. Sampath, Non-Linear Elastic Properties of Plasma-Sprayed Zirconia Coatings and Associated Relationships with Processing Conditions, Acta Mater., 2007, 55(14), p 4667-467810.1016/j.actamat.2007.04.037 ↗
28. Y.J. Liu, T. Nakamura, G. Dwivedi, A. Valarezo, and S. Sampath, Anelastic Behavior of Plasma-Sprayed Zirconia Coatings, J. Am. Ceram. Soc., 2008, 91(12), p 4036-404310.1111/j.1551-2916.2008.02789.x ↗
29. R.E. Taylor, Thermal Conductivity Determinations of Thermal Barrier Coatings, Mater. Sci. Eng. A, 1998, 245(2), p 160-16710.1016/S0921-5093(97)00847-2 ↗
30. W. Chi, “Thermal Transport Properties of Thermally Sprayed Coatings: An Integrated Study of Materials, Processing and Microstructural Effects,” Ph.D. thesis, Stony Brook University, 2007
31. A. Vaidya, “Process Maps for Thermal Spray: A Fundamental Approach to Process-Property Relationships,” Ph.D. thesis, Stony Brook University, 2008
32. S. Sampath, X. Jiang, A. Kulkarni, J. Matejicek, D.L. Gilmore, and R.A. Neiser, Development of Process Maps for Plasma Spray: Case Study for Molybdenum, Mater. Sci. Eng. A, 2003, 348(1-2), p 54-6610.1016/S0921-5093(02)00642-1 ↗
33. W. Zhang, L.L. Zheng, H. Zhang, and S. Sampath, Study of Injection Angle and Carrier Gas Flow Rate Effects on Particles In-Flight Characteristics in Plasma Spray Process: Modeling and Experiments, Plasma Chem. Plasma Process., 2007, 27(6), p 701-71610.1007/s11090-007-9101-3 ↗
34. A. Vaidya, S. Sampath, and H. Herman, Influence of Process Variables on the Plasma Sprayed Coatings: An Integrated Study, International Thermal Spray Conference (ITSC), 2001 (Singapore) (Materials Park, OH), ASM International, 200110.31399/asm.cp.itsc2001p1345 ↗
35. J. Matejicek and S. Sampath, In Situ Measurement of Residual Stresses and Elastic Moduli in Thermal Sprayed Coatings. Part 1: Apparatus and Analysis, Acta Mater., 2003, 51(3), p 863-87210.1016/S1359-6454(02)00478-0 ↗
36. J. Matejicek, S. Sampath, D. Gilmore, and R. Neiser, In Situ Measurement of Residual Stresses and Elastic Moduli in Thermal Sprayed Coatings. Part 2: Processing Effects on Properties of Mo Coatings, Acta Mater., 2003, 51(3), p 873-88510.1016/S1359-6454(02)00477-9 ↗
37. T. Streibl, A. Vaidya, M. Friis, V. Srinivasan, and S. Sampath, A Critical Assessment of Particle Temperature Distributions During Plasma Spraying: Experimental Results for YSZ, Plasma Chem. Plasma Process., 2006, 26(1), p 73-10210.1007/s11090-005-8727-2 ↗
38. T. Wentz, “Thermal Spray Process Variability and Methods of Control,” MS thesis, Stony Brook University, 2009
39. Y.P. Wan, H. Zhang, X.Y. Jiang, S. Sampath, and V. Prasad, Role of Solidification, Substrate Temperature and Reynolds Number on Droplet Spreading in Thermal Spray Deposition: Measurements and Modeling, J. Heat Transfer, 2001, 123(2), p 382-38910.1115/1.1351893 ↗
40. W. Zhang and S. Sampath, A Universal Method for Representation of In-Flight Particle Characteristics in Thermal Spray Processes, J. Therm. Spray Technol., 2009, 18(1), p 23-3410.1007/s11666-008-9214-0 ↗
41. W.G. Chi, S. Sampath, and H. Wang, Microstructure-Thermal Conductivity Relationships for Plasma-Sprayed Yttria-Stabilized Zirconia Coatings, J. Am. Ceram. Soc., 2008, 91(8), p 2636-264510.1111/j.1551-2916.2008.02476.x ↗