journal article·2010-01

Effect of Powder Characteristics on Properties of Warm-Sprayed WC-Co Coatings

Pornthep Chivavibul, Makoto Watanabe, Seiji Kuroda, Jin Kawakita, Masayuki Komatsu, Kazuto Sato, Junya Kitamura

Journal of Thermal Spray Technology· Volume 19· Issue 1-2
Publisher page

Abstract

In high-velocity oxy-fuel (HVOF) spraying of WC-Co coatings, the decomposition and decarburization of WC during deposition are responsible for their much lower toughness compared with a sintered bulk WC-Co. In a previous study, Warm Spray (WS) process, which is capable to control the flame temperature used to propel powder particles, was successfully applied in an attempt to suppress such detrimental reactions by keeping particles’ temperature lower than their melting point. The coatings deposited by WS process showed no or little formation of W2C and η phases and demonstrated moderately improved fracture properties. However, there is still a gap in fracture toughness between WS coatings and the corresponding sintered bulk. In order to optimize the properties of the WS coatings, the effect of original powder sizes were investigated. Microstructural characterization and phase analysis were carried out on deposited coatings by SEM and XRD. The results show that the feedstock powder size has substantial effects on the properties of the coatings, i.e., the smaller powder showed improved properties.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: High-Temperature Coating Behaviors · Advanced materials and composites · Nuclear Materials and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (23)

Show source-provided references
1. V.V. Sobolev, J.M. Guilemany, and J. Nutting, High Velocity Oxy-Fuel Spraying, Maney Publishing, 2004
2. J.M. Guilemany, J.M. de Paco, J. Nutting, and J.R. Miguel, Characterization of the W2C Phase Formed During the High Velocity Oxygen Fuel Spraying of a WC + 12 pct Co Powder, Metal. Mater. Trans. A, 1999, 30(8), p 1913-192110.1007/s11661-999-0002-3 ↗
3. C. Verdon, A. Karimi, and J.L. Martin, A Study of High Velocity Oxy-Fuel Thermally Sprayed Tungsten Carbide Based Coatings. Part 1: Microstructures, Mater. Sci. Eng. A, 1998, 246(1-2), p 11-2410.1016/S0921-5093(97)00759-4 ↗
4. Y. Ishikawa, J. Kawakita, S. Sawa, T. Itsukaichi, Y. Sakamoto, M. Takaya, and S. Kuroda, Evaluation of Corrosion and Wear Resistance of Hard Cermet Coatings Sprayed by Using an Improved HVOF Process, J. Therm. Spray Technol., 2005, 14(3), p 384-39010.1361/105996305X59378 ↗
5. P. Chivavibul, M. Watanabe, S. Kuroda, and K. Shinoda, Effects of Carbide Size and Co Content on the Microstructure and Mechanical Properties if HVOF-Sprayed WC-Co Coatings, Surf. Coat. Technol., 2007, 202(3), p 509-52110.1016/j.surfcoat.2007.06.026 ↗
6. M. Watanabe, A. Owada, S. Kuroda, and Y. Gotoh, Effect of WC Size on Interface Fracture Toughness of WC-Co HVOF Sprayed Coatings, Surf. Coat. Technol., 2006, 201(3-4), p 619-62710.1016/j.surfcoat.2005.12.019 ↗
7. Y. Ishikawa, S. Kuroda, J. Kawakita, Y. Sakamoto, and M. Takaya, Sliding Wear Properties of HVOF Sprayed WC-20%Cr3C2-7%Ni Cermet Coatings, Surf. Coat. Technol., 2007, 201(8), p 4718-472710.1016/j.surfcoat.2006.10.007 ↗
8. P. Chivavibul, M. Watanabe, S. Kuroda, J. Kawakita, M. Komatsu, K. Sato, and J. Kitamura, Development of WC-Co Coatings Deposited by Warm Spray Process, J. Therm. Spray Technol., 2008, 17(5-6), p 750-75610.1007/s11666-008-9271-4 ↗
9. R.S. Lima, J. Karthikeyan, C.M. Kay, J. Lindemann, and C.C. Berndt, Microstructural Characteristics of Cold-Sprayed Nanostructured WC-Co Coatings, Thin Solid Films, 2002, 416(1-2), p 129-13510.1016/S0040-6090(02)00631-4 ↗
10. H.J. Kim, C.H. Lee, and S.Y. Hwang, Superhard Nano WC-12%Co Coating by Cold Spray Deposition, Mater. Sci. Eng. A, 2005, 391(1-2), p 243-24810.1016/j.msea.2004.08.082 ↗
11. H.J. Kim, C.H. Lee, and S.Y. Hwang, Fabrication of WC-Co Coatings by Cold Spray Deposition, Surf. Coat. Technol., 2005, 191(2-3), p 335-34010.1016/j.surfcoat.2004.04.058 ↗
12. M. Watanabe, C. Pornthep, S. Kuroda, J. Kawakita, J. Kitamura, and K. Sato, Development of WC-Co Coatings by Warm Spray Deposition for Resource Savings of Tungsten, J. Jpn. Inst. Metals, 2007, 71, p 853-85910.2320/jinstmet.71.853 ↗
13. C.J. Li, G.J. Yang, P.H. Gao, J. Ma, Y.Y. Wang, and C.X. Li, Characterization of Nanostructured WC-Co Deposited by Cold Spraying, J. Therm. Spray Technol., 2007, 16, p 1011-102010.1007/s11666-007-9096-6 ↗
14. S. Kuroda, J. Kawakita, M. Watanabe, and H. Katanoda, Warm Spraying—A Novel Coating Process Based on High-Velocity Impact of Solid Particles, Sci. Technol. Adv. Mater., 2008, 9(3), p 033002 (17 pp)10.1088/1468-6996/9/3/033002 ↗
15. L. Jacobs, M.M. Hyland, and M. De Bonte, Comparative Study of WC-Cermet Coatings Sprayed via the HVOF and the HVAF Process, J. Therm. Spray Technol., 1998, 7(2), p 213-21810.1361/105996398770350954 ↗
16. L. Jacobs, M.M. Hyland, and M. De Bonte, Study of the Influence of Microstructural Properties on the Sliding-Wear Behavior of HVOF and HVAF Sprayed WC-Cermet Coatings, J. Therm. Spray Technol., 1999, 8(1), p 125-13210.1361/105996399770350656 ↗
17. M. Yandouzi, L. Ajdelsztajn, and B. Jodoin, WC-based Composite Coatings Prepared by the Pulsed Gas Dynamic Spraying Process: Effect of the Feedstock Powders, Surf. Coat. Technol., 2008, 202(16), p 3866-387710.1016/j.surfcoat.2008.01.036 ↗
18. M. Yandouzi, E. Sansoucy, L. Ajdelsztajn, and B. Jodoin, WC-based Cermet Coatings Produced by Cold Gas Dynamic and Pulsed Gas Dynamic Spraying Processes, Surf. Coat. Technol., 2007, 202(2), p 382-39010.1016/j.surfcoat.2007.05.095 ↗
19. J. Kawakita, S. Kuroda, T. Fukushima, H. Katanoda, K. Matsuo, and H. Fukanuma, Dense Titanium Coatings by Modified HVOF Spraying, Surf. Coat. Technol., 2006, 201(3-4), p 1250-125510.1016/j.surfcoat.2006.01.056 ↗
20. K. Niihara, A Fracture-Mechanics Analysis of Indentation-Induced Palmqvist Crack in Ceramics, J. Mater. Sci. Lett., 1983, 2(5), p 221-22310.1007/BF00725625 ↗
21. J. Barber, B.G. Mellor, and R.J.K. Wood, The Development of Sub-surface Damage During High Energy Solid Particle Erosion of a Thermally Sprayed WC-Co-Cr Coating, Wear, 2005, 259(1-6), p 125-13410.1016/j.wear.2005.02.008 ↗
22. J.K.N. Murthy, D.S. Rao, and B. Venkataraman, Effect of Grinding on the Erosion Behaviour of a WC-Co-Cr Coating Deposited by HVOF and Detonation Gun Spray Processes, Wear, 2001, 249(7), p 592-60010.1016/S0043-1648(01)00682-2 ↗
23. G.C. Ji, C.J. Li, Y.Y. Wang, and W.Y. Li, Erosion Performance of HVOF-Sprayed Cr3C2-NiCr Coatings, J. Therm. Spray Technol., 2007, 16(4), p 557-56510.1007/s11666-007-9052-5 ↗