Corrosion and Wear Studies of Cr3C2NiCr-HVOF Coatings Sprayed on AA7050 T7 Under Cooling
Source abstract
Abstract
In this work, cermet coatings were prepared by high-velocity oxygen-fuel (HVOF) technique using a Diamalloy 3007 powder. The influence of the spray parameters on corrosion, friction, and abrasive wear resistance was studied. The samples were obtained using the standard conditions (253 L/min of oxygen and 375 L/min of compressed air), higher oxygen flux (341 L/min), and higher carrier gas flux (500 L/min). The coatings were characterized using scanning electron microscopy (SEM), and x-ray diffraction (XRD). X-ray diffraction and SEM studies showed well-bounded coating/substrate interface, pores, metallic matrix, chromium oxides, carbides, and carbides dissolution into the matrix. In comparison with the standard condition, the sample prepared using higher oxygen flux showed the highest carbide dissolution because of the high temperature achieved in the spray process. When the carrier gas flux was increased, the sample showed denser structure because of the higher particle velocity. The friction and abrasive wear resistance of the coatings were studied using rubber wheel and ball-on-disk tests. All samples showed similar sliding and abrasive behavior, and all of them showed better performance than the aluminum alloy. The electrochemical behavior was evaluated using open-circuit potential (EOC) measurements, electrochemical impedance spectroscopy (EIS), and potentiodynamic polarization curves. The coating prepared with higher carrier gas flux showed the highest corrosion resistance in 3.5% NaCl solution and probably no pitting attack to the substrate occurred even after around 26 h of test. Tests performed for longer immersion times showed that the total impedance values significantly decreased (6 and 4 times) for samples sprayed using standard and higher oxygen flux, and no great change for sample sprayed using higher carrier gas flux was observed. The last sample presents a corrosion resistance around 200 times higher than the others.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloys Composites Properties · MXene and MAX Phase Materials · Advanced materials and composites
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (40)
Show source-provided references
1. Y. Sun, Tribological Rutile-TiO2 Coating on Aluminium Alloy, Appl. Surf. Sci., 2004, 233(1-4), p 328-335.10.1016/j.apsusc.2004.03.241 ↗
2. M.J. Ghazali, W.M. Rainforth, and H. Jones, The Wear of Wrought Aluminium Alloys under Dry Sliding Conditions, Tribol. Int., 2007, 40(2), p 160-169.10.1016/j.triboint.2005.09.009 ↗
3. P. Leo, E. Cerri, P.P. Marco, and H.J. Roven, Properties and Deformation Behaviour of Severe Plastic Deformed Aluminium Alloys, J. Mater. Process. Technol., 2007, 2(1-3), p 207-214.10.1016/j.jmatprotec.2006.07.038 ↗
4. T. Yasmin, A.A. Khalid, and M.M. Haque, Tribological (Wear) Properties of Aluminum-Silicon Eutectic Base Alloy Under Dry Sliding Condition, J. Mater. Process. Technol., 2004, 153-154(10), p 833-838.10.1016/j.jmatprotec.2004.04.147 ↗
5. J.C. Lin, H.-L Liao, W.-D. Jehng, C.-H. Chang, and S.-L. Lee, Effect of Heat Treatments on the Tensile Strength and SCC-Resistance of AA7050 in an Alkaline Saline Solution, Corros. Sci., 2006, 48(10), p 3139-3156.10.1016/j.corsci.2005.11.009 ↗
6. L. Ceschini, I. Boromei, G. Minak, A. Morri, and F. Tarterini, Microstructure, Tensile and Fatigue Properties of AA6061/20 vol% Al2O3p friction stir welded joints, Composites Part A: Appl. Sci. Manuf., 2007, 38(4), p 1200-1210.10.1016/j.compositesa.2006.06.009 ↗
7. R.G. Rateick, T.C. Binkowski, and B.C. Boray, Effects of Hard Anodize Thickness on the Fatigue of AA6061 and C355 Aluminium, J. Mater. Sci. Lett., 1996, 15(15), p 1321-1323.10.1007/BF00240794 ↗
8. A. Merati and G. Eastaugh, Determination of Fatigue Related Discontinuity State of 7000 Series of Aerospace Aluminum Alloys, Eng. Fail. Anal., 2007, 14(4), p 673-685.10.1016/j.engfailanal.2006.02.016 ↗
9. R.L. Deuis, C. Subramanian, and J.M. Yellup, Abrasive Wear of Composite Coatings in a Salines and Slurry Environment, Wear, 1997, 203-204, p 119-128.10.1016/S0043-1648(96)07422-4 ↗
10. K. Kawata, H. Sugimura, and O. Takai, Characterization of Multilayer Films of Ti-Al-O-C-N System Prepared by Pulsed d.c. Plasma-Enhanced Chemical Vapor Deposition, Thin Solid Films, 2001, 390(1-2), p 64-69.10.1016/S0040-6090(01)00939-7 ↗
11. H. Hoche, C. Blawert, E. Broszeit, and C. Berger, Galvanic Corrosion Properties of Differently PVD-Treated Magnesium Die Cast Alloy AZ9, Surf. Coat. Technol., 2005, 193(1-3), p 223-229.10.1016/j.surfcoat.2004.08.147 ↗
12. M. Khaled, B.S. Yilbas, and J. Shirokoff, Electrochemical Study of Laser Nitrided and PVD TiN Coated Ti-6Al-4 V Alloy: The Observation of Selective Dissolution, Surf. Coat. Technol., 2001, 148(1), p 46-54.10.1016/S0257-8972(01)01326-3 ↗
13. K.S. Klimek, H. Ahn, I. Seebach, M. Wang, and K.T. Rie, Duplex Process Applied for Die-Casting and Forging Tools, Surf. Coat. Technol., 2003, 174-175, p 677-680.10.1016/S0257-8972(03)00365-7 ↗
14. J.V. Ringleben, Ch. Sundermann, T. Matsutani, M. Kiuchi, and W. Ensinger, Sealing Performance of Thin Amorphous Carbon Films Formed by Ion Beam Assisted Deposition at Low Temperature for Protection of Aluminium against Aggressive Media: The Influence of the Ion Energy, Thin Solid Films, 2005, 482(1-2), p 115-119.10.1016/j.tsf.2004.11.127 ↗
15. A.L.M. Carvalho and H.J.C. Voorwald, Influence of Shot Peening and Hard Chromium Electroplating on the Fatigue Strength of 7050-T7451 Aluminum Alloy, Int. J. Fat., 2007, 29(7), p 1282-1291.10.1016/j.ijfatigue.2006.10.003 ↗
16. M. Magnani, A.V. Benedetti, C.S. Fugivara, P.H. Suegama, and J.M. Guilemany, Analysis of Electrochemical Impedance and Noise Data for Thermal Spray Coatings in 3.5% NaCl Solution, EUROCORR 2005 (Lisboa-Portugal), Anais do EUROCORR, 2005.
17. S. Uozato, K. Nakata, and M. Ushio, Evaluation of Ferrous Powder Thermal Spray Coatings on Diesel Engine Cylinder Bores, Surf. Coat. Technol., 2005, 200(7), p 2580-2586.10.1016/j.surfcoat.2005.05.042 ↗
18. M.F. Morks, Y. Gao, N.F. Fahim, F.U. Yingqing, and M.A. Shoeib, Influence of Binder Materials on the Properties of Low Power Plasma Sprayed Cermet Coatings, Surf. Coat. Technol., 2005, 199(1), p 66-71.10.1016/j.surfcoat.2005.02.159 ↗
19. A. Edrisy, T. Perry, and A.T. Alpas, Investigation of Scuffing Damage in Aluminum Engines with Thermal Spray Coating, Wear, 2005, 259(7-12), p 1056-1062.10.1016/j.wear.2005.02.048 ↗
20. A. Edrisy, T. Perry, Y.T. Cheng, and A.T. Alpas, Wear of Thermal Spray Deposited Low Carbon Steel Coatings on Aluminum Alloys, Wear, 2001, 251(1-12), p 1023-1033.10.1016/S0043-1648(01)00718-9 ↗
21. P.M. Natishan, S.H. Lawrence, R.L. Foster, J. Lewis, and B.D. Sartwell, Salt Fog Corrosion Behavior of High-Velocity Oxygen-Fuel Thermal Spray Coatings Compared to Electrodeposited Hard Chromium, Surf. Coat. Technol., 2000, 130(2-3), p 218-223.10.1016/S0257-8972(00)00671-X ↗
22. J.K.N, Murthy and B. Venkataraman, Abrasive Wear Behaviour of WC-CoCr and Cr3C2-20(NiCr) Deposited by HVOF and Detonation Spray Processes, Surf. Coat. Technol., 2006, 200(8), p 2642-2652.10.1016/j.surfcoat.2004.10.136 ↗
23. M.P. Nascimento, R.C. Souza, I.M. Miguel, W.L. Pigatin, and H.J.C. Voorwald, Effects of Tungsten Carbide Thermal Spray Coating by HP/HVOF and Hard Chromium Electroplating on AISI 4340 High Strength Steel, Surf. Coat. Technol., 2001, 138(2-3), p 113-124.10.1016/S0257-8972(00)01148-8 ↗
24. Y. Xie and H.M. Hawthorne, The Damage Mechanisms of Several Plasma-Sprayed Ceramic Coatings in Controlled Scratching, Wear, 1999, 233-235, p 293-305.10.1016/S0043-1648(99)00211-2 ↗
25. J.M. Guilemany, N. Espallargas, P.H. Suegama, and A.V. Benedetti, Comparative Study of Cr3C2-NiCr Coatings Obtained by HVOF and Hard Chromium Coatings, Corros. Sci., 2006, 48(10), p 2998-3013.10.1016/j.corsci.2005.10.016 ↗
26. P.H. Suegama, C.S. Fugivara, A.V. Benedetti, J. Fernández, J. Delgado, and J.M. Guilemany, Electrochemical Behaviour of Thermally Sprayed Cr3C2-NiCr Coatings in 0.5 m H2SO4 Environment, J. Appl. Electrochem., 2002, 14, p 1287-1295.10.1023/A:1021654628416 ↗
27. J.M. Guilemany, C. Lorenzana, J. Nin, and J. Delgado, On-Line Monitoring Control of Stainless Steel Coatings Obtained by HVOF and APS Processes, Proceedings of the United Thermal Spray Congress and Exhibition (UTSC’2002) (Essen, Germany), 2002, p 86-9010.31399/asm.cp.itsc2002p0086 ↗
28. L. Pawlowski, The Science and Engineering of Thermal Spray Coatings, John Wiley & Sons, New York, 1995.
29. V. Sobolev, J.M. Guilemany, and J. Nutting, High Velocity Oxy-Fuel Spraying, Maney, England, 2004.
30. P.H. Suegama, C.S. Fugivara, A.V. Benedetti, J. Fernández, N. Espallargas, J. Delgado, and J.M. Guilemany, Microstructure and Electrochemical Studies of Cr 3 C 2 -NiCr Coatings, E.P. Vargus, Ed., New Researches on Electrochemistry, Nova Science Publishers, New York, 2007, p 113
31. P.H. Suegama, N. Espallargas, J.M. Guilemany, J. Fernández, and A.V. Benedetti, Electrochemical and Structural Characterization of Treated Cr3C2-NiCr Coatings, J. Electrochem. Soc., 2006, 153, p B434-B445.10.1149/1.2229288 ↗
32. M. Magnani, P.H. Suegama, A.A.C. Recco, J.M. Guilemany, C.S. Fugivara, and A.V. Benedetti, WC-CoCr Coatings Sprayed by High Velocity Oxygen-Fuel (HVOF) Flame on AA7050 Aluminum Alloy: Electrochemical Behavior in 3.5% NaCl Solution, Mater. Res., 2007, 10(4), p 377-385.10.1590/S1516-14392007000400010 ↗
33. J.A. Picas, A. Forn, R. Rilla, and E. Martin, HVOF Thermal Sprayed Coatings on Aluminium Alloys and Aluminium Matrix Composites, Surf. Coat. Technol., 2005, 200(1-4), p 1178-1181.10.1016/j.surfcoat.2005.02.124 ↗
34. M. Wenzelburger, M. Escribano, and R. Gadow, Modeling of Thermally Sprayed Coatings on Light Metal Substrates: Layer Growth and Residual Stress Formation, Surf. Coat. Technol., 2004, 180-181, p 429-435.10.1016/j.surfcoat.2003.10.125 ↗
35. M. Magnani, P.H. Suegama, N. Espallargas, S. Dosta, C.S. Fugivara, J.M. Guilemany, and A.V. Benedetti, Influence of HVOF Parameters on the Corrosion and Wear Resistance of WC-Co Coatings Sprayed on AA7050 T7, Surf. Coat. Technol., 2008, 202(19), p 4746-4757.10.1016/j.surfcoat.2008.04.055 ↗
36. “Properties and Selection: Nonferrous Alloys and Special-Purpose Materials,” ASM Handbook, Vol 2, 10th ed., ASM International, Materials Park, OH, 1992, p 1328
37. J. Yan, L. Chunzhi, and Y. Minggao, On the η′ Precipitate Phase in 7050 Aluminium Alloy, Mater. Sci. Eng., 1991, A141, p 123-128.10.1016/0921-5093(91)90715-Y ↗
38. M.I. Hutchings, Tribology, Friction and Wear of Engineering Materials, London: CRC Press, 1992, p 273.
39. P.H. Suegama, C.S. Fugivara, A.V. Benedetti, J.M. Guilemany, J. Fernández, and J. Delgado, The Influence of Gun Transverse Speed on Electrochemical Behaviour of Thermally Sprayed Cr3C2-NiCr Coatings in 0.5 M H2SO4 Solution, Electrochim. Acta, 2004, 49, p 627-634.10.1016/j.electacta.2003.09.017 ↗
40. P.L. Cabot, F. Centellas, J.A. Garrido, E. Perez, A.H. Moreira, P.T.A. Sumodjo, A.V. Benedetti, and W.G. Proud, Characterization of Localized Corrosion Processes in Al-Zn-Mg Alloys by Impedance Spectroscopy, Progress in the Understanding and Prevention of Corrosion, J.M. Costa and A.D. Mercer, Eds., Institute of Materials, London, 2, 1993, p 1409-1418