journal article·2013-03

Effect of Substrate Temperature on Cold-Gas-Sprayed Coatings on Ceramic Substrates

K.-R. Ernst, J. Braeutigam, F. Gaertner, T. Klassen

Journal of Thermal Spray Technology· Volume 22· Issue 2-3
Publisher page

Abstract

Abstract The focus of this study is to deposit metallic coatings onto ceramic substrates for application in power electronics. One possibility to achieve the required surface activation is to heat the substrate during spraying. An increased substrate temperature significantly influences bond strength and coating properties. This is investigated for cold-gas sprayed copper and aluminum on thermally sprayed Al2O3 layers. The study examines the adhesion of single-impacting Cu particles as well as coating microstructures and mechanical and electrical coating properties. It is found that increasing the substrate temperature as well as increasing the surface roughness enhances the adhesion strength of single particles. Coatings sprayed on heated substrates adhere very well and show low compressive stresses. Their hardness is reduced significantly, while their electrical conductivity is optimized to values of over 90 % IACS (IACS: International annealed Copper standard, 100 % IACS equals 58 MS/m).
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: High-Temperature Coating Behaviors · Advanced ceramic materials synthesis · Advanced materials and composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (40)

Show source-provided references
1. K.-R. Donner, F. Gaertner, and T. Klassen, Metallization of Thin Al2O3 Layers in Power Electronics Using Cold Gas Spraying, J. Therm. Spray Technol., 2011, 20(1-2), p 299-30610.1007/s11666-010-9573-1 ↗
2. F. Trenkle, H.-P. Vollmar, and S. Hartmann, Testing of the Electric Conductivity of Non-ferrous Metallic Coatings, International Thermal Spray Conference 2011, September 27-29, 2011 (Hamburg, Germany), DVS-Berichte, DVS Media.10.31399/asm.cp.itsc2011p0521 ↗
3. V.F. Kosarev, S.V. Klinkov, A.P. Alkhimov, and A.N. Papyrin, On Some Aspects of Gas Dynamics of the Cold Spray Process, J. Therm. Spray Technol., 2003, 12(2), p 265-28110.1361/105996303770348384 ↗
4. E. Irissou, J.G. Legoux, C. Moreau, and A.N. Ryabinin, How cold is cold spray? An experimental study of the heat transfer to the substrate in cold gas dynamic spraying, International Thermal Spray Conference 2008, June 2-4 2008 (Maastricht, Netherlands), DVS-Verlag GmbH, p 625-631.10.31399/asm.cp.itsc2008p0613 ↗
5. S. Yin, X.-F. Wang, W.-Y. Li, and X.-P. Guo, Examination on Substrate Preheating Process in Cold Gas Dynamic Spraying, J. Therm. Spray Technol., 2011, 20(4), p 852-85910.1007/s11666-011-9623-3 ↗
6. S.V. Klinkov, V.F. Kosarev, and M. Rein, Cold Spray Deposition: Significance of Particle Impact Phenomena, Aerosp. Sci. Technol., 2005, 9(7), p 582-59110.1016/j.ast.2005.03.005 ↗
7. J.G. Legoux, E. Irissou, and C. Moreau, Effect of Substrate Temperature on the Formation Mechanism of Cold-Sprayed Aluminum, Zinc and Tin Coatings, J. Therm. Spray Technol., 2007, 16(5-6), p 619-62610.1007/s11666-007-9091-y ↗
8. M. Fukumoto, H. Wada, K. Tanabe, M. Yamada, E. Yamaguchi, A. Niwa, M. Sugimoto, and M. Izawa, Effect of Substrate Temperature on Deposition Behavior of Copper Particles on Substrate Surfaces in the Cold Spray Process, J. Therm. Spray Technol., 2007, 16(5-6), p 643-65010.1007/s11666-007-9121-9 ↗
9. W. Wong, E. Irissou, A.N. Ryabinin, J.-G. Legoux, and S. Yue, Influence of Helium and Nitrogen Gases on the Properties of Cold Gas Dynamic Sprayed Pure Titanium Coatings, J. Therm. Spray Technol., 2011, 20(1-2), p 213-22610.1007/s11666-010-9568-y ↗
10. D. Goldbaum, J.M. Shockley, R.R. Chromik, A. Rezaeian, S. Yue, J.-G. Legoux, and E. Irissou, The Effect of Deposition Conditions on Adhesion Strength of Ti and Ti6Al4V Cold Spray Splats, J. Therm. Spray Technol., 2012, 21(2), p 288-30310.1007/s11666-011-9720-3 ↗
11. P. Fauchais, M. Fukumoto, A. Vardelle, and M. Vardelle, Knowledge Concerning Splat Formation: An Invited Review, J. Therm. Spray Technol., 2004, 13(3), p 337-36010.1361/10599630419670 ↗
12. X.Y Jiang, Y.P. Wan, H. Herman, and S. Sampath, Role of Condensates and Adsorbates on Substrate Surface on Fragmentation of Impinging Molten Droplets During Thermal Spray, Thin Solid Films, 2001, 385(1-2), p 132-14110.1016/S0040-6090(01)00769-6 ↗
13. C.-J. Li, J.-L. Li, and W.-B. Wang, The Effect of Substrate Preheating and Surface Organic Covering on Splat Formation, International Thermal Spray Conference 1998, C. Coddet, Ed., May 25-29 1998 (Nice, France), ASM International, p 473-48010.31399/asm.cp.itsc1998p0473 ↗
14. C.-J. Li and J.-L. Li, Evaporated-Gas-Induced Splashing Model for Splat Formation During Plasma Spraying, Surf. Coat. Technol., 2004, 184(1), p 13-2310.1016/j.surfcoat.2003.10.048 ↗
15. A. Abedini, A. Pourmousa, S. Chandra, and J. Mostaghimi, Effect of Substrate Temperature on the Properties of Coatings and Splats Deposited by Wire Arc Spraying, Surf. Coat. Technol., 2006, 201(6), p 3350-335810.1016/j.surfcoat.2006.07.184 ↗
16. D. Christoulis, D. Pantelis, F. Borit, V. Guipont, and M. Jeandin, Effect of Substrate Preparation on Flattening of Plasma Sprayed Aluminium Bronze Powders, Surf. Eng., 2006, 22(6), p 420-43110.1179/174329406X150440 ↗
17. H. Li, S. Costil, H. Liao, C. Li, M. Planche, and C. Coddet, Effects of Surface Conditions on the Flattening Behavior of Plasma Sprayed Cu Splats, Surf. Coat. Technol., 2006, 200(18-19), p 5435-544610.1016/j.surfcoat.2005.07.058 ↗
18. M. Fukumoto, T. Yamaguchi, M. Yamada, and T. Yasui, Splash Splat to Disk Transition Behavior in Plasma-Sprayed Metallic Materials, J. Therm. Spray Technol., 2007, 16(5), p 905-91210.1007/s11666-007-9083-y ↗
19. K. Yang, K. Tomita, M. Fukumoto, M. Yamada, and T. Yasui, Effect of Ambient Pressure on Flattening Behavior of Thermal Sprayed Particles, J. Therm. Spray Technol., 2009, 18(4), p 510-51810.1007/s11666-009-9401-7 ↗
20. A. Tran and M. Hyland, The Role of Substrate Surface Chemistry on Splat Formation During Plasma Spray Deposition by Experiments and Simulations, J. Therm. Spray Technol., 2009, 19(1-2), p 11-2310.1007/s11666-009-9414-2 ↗
21. K. Yang, M. Fukumoto, T. Yasui, and M. Yamada, Study of Substrate Preheating on Flattening Behavior of Thermal-Sprayed Copper Particles, J. Therm. Spray Technol., 2010, 6(19), p 1195-120510.1007/s11666-010-9515-y ↗
22. V. Coustet and J. Jupille, High-Resolution Electron-Energy-Loss Spectroscopy of Isolated Hydroxyl Groups on α-Al2O3(0001), Surf. Sci., 1994, 307-309, p 1161-116510.1016/0039-6028(94)91557-1 ↗
23. J.W. Elam, C.E. Nelson, M.A. Cameron, M.A. Tolbert, and S.M. George, Adsorption of H2O on a Single-Crystal α-Al2O3(0001) Surface, J. Phys. Chem. B, 1998, 102(36), p 7008-701510.1021/jp981070j ↗
24. P. Liu, T. Kendelewicz, G.E. Brown, E.J. Nelson, and S.A. Chambers, Reaction of Water Vapor with α-Al2O3(0001) and α-Fe2O3(0001) Surfaces: Synchrotron X-ray Photoemission Studies and Thermodynamic Calculations, Surf. Sci., 1998, 417, p 53-6510.1016/S0039-6028(98)00661-X ↗
25. K.C. Hass, W.F. Schneider, A. Curioni, and W. Andreoni, The Chemistry of Water on Alumina Surfaces: Reaction Dynamics from First Principles, Science, 1998, 282, p 265-26810.1126/science.282.5387.265 ↗
26. M.A. Henderson, The Interaction of Water with Solid Surfaces: Fundamental Aspects Revisited, Surf. Sci. Rep., 2002, 46, p 1-30810.1016/S0167-5729(01)00020-6 ↗
27. P. Thissen, G. Grundmeier, S. Wippermann, and W.G. Schmidt, Water Adsorption on the α-Al2O3(0001) Surface, Phys. Rev. B, 2009, 80, p 2454032810.1103/PhysRevB.80.245403 ↗
28. E. Sánchez-González, J. Meléndez-Martínez, A. Pajares, P. Miranda, F. Guiberteau, and B. Lawn, Application of Hertzian Tests to Measure Stress-Strain Characteristics of Ceramics at Elevated Temperatures, J. Am. Ceram. Soc., 2007, 90(1), p 149-15310.1111/j.1551-2916.2006.01339.x ↗
29. H. Xu, C. Ostertag, and R. Krause, Effect of Temperature on Toughness Curves in Alumina, J. Am. Ceram. Soc., 1995, 78(1), p 260-26210.1111/j.1151-2916.1995.tb08399.x ↗
30. J. Najar, V. Silberschmidt, and M. Müller-Bechtel, Enhanced Fracture Energy and Effects of Temperature at Spalling in Ceramics: Continuum Damage Modelling, Arch. Appl. Mech., 2000, 70, p 145-15710.1007/s004199900054 ↗
31. R. Rice, Effects of Environment and Temperature on Ceramic Tensile Strength-Grain Size Relations, J. Mater. Sci., 1997, 32, p 3071-308710.1023/A:1018630113180 ↗
32. M. Mellali, P. Fauchais, and A. Grimaud, Influence of Substrate Roughness and Temperature on the Adhesion/Cohesion of Alumina Coatings, Surf. Coat. Technol., 1996, 81(2-3), p 275-28610.1016/0257-8972(95)02540-5 ↗
33. A. Tran, S. Brossard, M. Hyland, B. James, and P. Munroe, Evidence of Substrate Melting of NiCr Particles on Stainless Steel Substrate by Experimental Observation and Simulations, Plasma Chem. Plasma P., 2009, 29(6), p 475-49510.1007/s11090-009-9192-0 ↗
34. T. Schmidt, H. Assadi, F. Gaertner, H. Richter, T. Stoltenhoff, H. Kreye, and T. Klassen, From Particle Acceleration to Impact and Bonding in Cold Spraying, J. Therm. Spray Technol., 2009, 18(5-6), p 794-80810.1007/s11666-009-9357-7 ↗
35. C. Borchers, F. Gaertner, and T. Stoltenhoff, Microstructural and Macroscopic Properties of Cold Sprayed Copper Coatings, J. Appl. Phys., 2003, 93(12), p 10064-1007010.1063/1.1573740 ↗
36. G. Bae, Y. Xiong, S. Kumar, K. Kang, and C. Lee, General Aspects of Interface Bonding in Kinetic Sprayed Coatings, Acta Mater., 2008, 56, p 4858-486810.1016/j.actamat.2008.06.003 ↗
37. K. Binder, Kaltgasspritzen von ermüdungsfesten Titanschichten (Cold Gas Spraying of Fatigue Resistant Titanium Coatings), Ph.D. Thesis, Helmut Schmidt University, Germany, to be published 2012
38. Materials properties data base: www.matweb.com
39. F. Gärtner, T. Stoltenhoff, J. Voyer, H. Kreye, S. Riekehr, and M. Kocak, Mechanical Properties of Cold-Sprayed and Thermally Sprayed Copper Coatings, Surf. Coat. Technol., 2006, 200, p 6770-678210.1016/j.surfcoat.2005.10.007 ↗
40. T. Schmidt, F. Gaertner, and H. Kreye, New Developments in Cold Spray Based on Higher Gas and Particle Temperatures, J. Therm. Spray Technol., 2006, 15(4), p 488-49410.1361/105996306X147144 ↗