journal article·2009-12

Calculation of Particle Parameters for Cold Spraying of Metal-Ceramic Mixtures

S. V. Klinkov, V. F. Kosarev, A. A. Sova, I. Smurov

Journal of Thermal Spray Technology· Volume 18· Issue 5-6
Publisher page

Abstract

Formation of metal-ceramic composite coatings by cold spray is one of the major directions in the development and application of the technology. As experiments showed, addition of a hard ceramic component into the mixture can shift the transition from substrate erosion to particles adhesion closer to adhesion. This effect may be induced by ceramic particles which not only erode, but also activate the target surface. Velocity and temperature of particles at their high-velocity impact onto the substrate are governing parameters in particles/substrate interaction. These parameters influence both the process of metal particles deposition and the process of erosion/activation of the substrate surface by ceramic particles. Metallic and ceramic particles collide with each other in the gas stream. These collisions can produce preactivation effect on metal particles by cleaning their surface. The level of activation depends on a typical velocity of collision which is the difference between velocities of metal and ceramic particles. Parameters of metallic and ceramic particles in the gas stream are estimated. Calculations show that components of mixtures with fine abrasive particles have greatly different velocities that influences preactivation of metal particles. At the same time, the substrate surface is activated by fine abrasive particles characterized by a high-impact velocity.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: High-Temperature Coating Behaviors · Advanced materials and composites · Particle Dynamics in Fluid Flows

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (20)

Show source-provided references
1. A. Papyrin, V. Kosarev, S. Klinkov, A. Alkhimov, V. Fomin, Cold Spray Technology, Elsevier Science, Amsterdam, 2007, p.336
2. T. Schmidt, F. Gaertner, H. Assadi, H. Kreye, Development of a generalized parameter window for cold spray deposition, Acta Materialia, 2006, 54, p 729-74210.1016/j.actamat.2005.10.005 ↗
3. M. Grujicic, C.L. Zhao, W.S. DeRosset, D. Helfritch, Adiabatic Shear Instability Based Mechanism for Particles/Substrate Bonding in the Cold-Gad Dynamic-Spray Process, Materials and Design, 2004, 25, p 681-68810.1016/j.matdes.2004.03.008 ↗
4. H. Assadi, F. Gaertner, T. Stoltenhoff, H. Kreye, Bonding Mechanism in Cold Gas Spraying, Acta Materialia, 2003, 51, p 4379-439410.1016/S1359-6454(03)00274-X ↗
5. A. Shkodkin, A. Kashirin, O. Klyuev and T.Buzdygar (2006) Metal Particle Deposition Stimulation by Surface Abrasive Treatment in Gas Dynamic Spraying. J. Therm. Spray Technol., 15: 382-38510.1361/105996306X124383 ↗
6. R. Maev, V. Leshchynsky, Introduction to low pressure gas dynamic spray: physics & technology, WILEY-VCH, Weinheim, 2008, p 234
7. Maev, R.G., and Leshchynsky, V.: Air Gas Dynamic Spraying in Powder Mixtures: Theory and Application, Journal of Thermal Spray Technology, 2006, 15, p.198-20510.1361/105996306X108048 ↗
8. Ha Yong Lee, Se Hun Jung, Soo Yong Lee, Young Ho You, Kyung Hyun Ko, Correlation between Al2O3 particles and interface of Al-Al2O3 coatings by cold spray, Applied Surface Science, 2005, 252, p.1891-189810.1016/j.apsusc.2005.03.148 ↗
9. A. Papyrin, V. Kosarev, S. Klinkov, A. Sova, I. Smurov, and P. Bertrand, Investigation of Composites: Metal—Ceramics and Metal—Metal Coatings Produced with Cold Spray Equipment with Ejector, Thermal Spray Crossing Borders: Proceedings of the 2008 International Thermal Spray Conference, E. Lugscheider, Ed., June 2-4, 2008 (Maastricht, Netherlands), ASM International, 200810.31399/asm.cp.itsc2008p0599 ↗
10. Tien-Chien Jen, Longjian Li, Wenzhi Cui, Qinghua Chen, Xinming Zhang Numerical investigations on cold gas dynamic spray process with nano- and microsize particles, International Journal of Heat and Mass Transfer, 2005, 48, p. 4384-439610.1016/j.ijheatmasstransfer.2005.05.008 ↗
11. Wen-Ya Li, Hanlin Liao, G. Douchy, C. Coddet, Optimal design of a cold spray nozzle by numerical analysis of particle velocity and experimental validation with 316L stainless steel powder, Materials & Design, 2007, 28, p. 2129-213710.1016/j.matdes.2006.05.016 ↗
12. Wen-Ya Li, Hanlin Liao, Hong-Tao Wang, Chang-Jiu Li, Ga Zhang and C. Coddet Optimal design of a convergent-barrel cold spray nozzle by numerical method, Applied Surface Science, 2006, 253, p. 708-71310.1016/j.apsusc.2005.12.157 ↗
13. G.N. Abramovich, Applied Gas Dynamics, Nauka, Moscow, 1976, p 824 (in Russian)
14. R.C. Dykhuizen, M.F. Smith, Gas Dynamic Principles of Cold Spray, J. Therm. Spray Technol., 1998, 7 (2), p. 205-21210.1361/105996398770350945 ↗
15. M. Grujicic, C.L. Zhaoa, C. Tonga, W.S. DeRosset, D. Helfritch, Analysis of the impact velocity of powder particles in the cold-gas dynamic-spray process, Materials Science and Engineering, 2004, 368, p. 222-23010.1016/j.msea.2003.10.312 ↗
16. G. Schlichting, Theory of Boundary Layer, Nauka, Moscow, 1974, p 742 (in Russian)
17. M.E. Deich and A.E. Zaryankin, Gas Dynamic of Diffusors and Exhaust Hood, Energiya, Moscow, 1970, p 384 (in Russian)
18. I.A. Belov, I.P. Ginzburg and L.I. Shoob, Supersonic underexpanded jet impingement upon flat plate, Int. J. Heat and Transfer, 1973, 16, p. 2067-207610.1016/0017-9310(73)90109-9 ↗
19. T. Nakatogawa, M. Hirata and I. Kukita, Desintegration of a supersonic jet impinging normally on a flat plate, J. Spacecraft, 1971, 8(4), p. 410-41110.2514/3.30290 ↗
20. C.B. Henderson, Drag Coefficient of Spheres in Continuum and Rarefied Flows, AIAA J., 1976, 14, p. 707-70810.2514/3.61409 ↗