journal article·2015-02

Effect of Surface Preparation on the Microstructure, Adhesion, and Tensile Properties of Cold-Sprayed Aluminum Coatings on AA2024 Substrates

M. M. Sharma, T. J. Eden, B. T. Golesich

Publisher page

Abstract

Commercially pure aluminum coatings (CP-Al) were applied to AA 2024-T351 substrates utilizing the cold spray process using different surface preparation methods and carrier gases; the resulting microstructures and mechanical properties were investigated. Substrate preparation methods were examined to understand the effect of substrate roughness on coating properties, to minimize embedded grit, and to identify the surface preparation method that yielded the best combination of coating properties. Three substrate roughing preparations, glass bead, SiC grit, and alumina grit blast, were examined while utilizing both helium and nitrogen as carrier gases in the cold spray process. Coatings that were oxide free, possessing densities greater than 99% were achieved, with the mean coating porosity ranging 0.1-0.5%. The highest mean adhesion strength was 42 MPa for the nitrogen gas and 20 MPa for the helium gas, both using glass bead surface preparation. For the nitrogen process gas samples, the surface preparation methods that produced high pull strengths correlated to bend test specimens that showed no signs of cracking on surfaces or edges. The overall best combination of mechanical property results was achieved with coatings prepared by glass bead surface roughening using nitrogen as a carrier gas.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: High-Temperature Coating Behaviors · Advanced ceramic materials synthesis · Aluminum Alloys Composites Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (32)

Show source-provided references
1. J.R. Davis, Ed., Aluminum and Aluminum Alloys, ASM Specialty Handbook ® , ASM International, Materials Park, OH, 1993.
2. W.K. Chen, C.Y. Bai, C.M. Liu, C.S. Lin, and M.D. Ger, The Effect of Chromic Sulfate Concentration and Immersion Time on the Structures and Anticorrosive Performance of the Cr(III) Conversion Coatings on Aluminum Alloys, Appl. Surf. Sci., 2010, 256, p 4924-492910.1016/j.apsusc.2010.03.003 ↗
3. X.Q. Liu, Y.G. Zheng, X.C. Chang, W.L. Hou, J.Q. Wang, Z. Tang, and A. Burgess, Microstructure and Properties of Fe-Based Amorphous Metallic Coating Produced by High Velocity Axial Plasma Spraying, J. Alloys Compd., 2009, 484, p p300-p30710.1016/j.jallcom.2009.04.086 ↗
4. M. Diesselberg, H.-R. Stock, and M. P. Mayr, Corrosion Protection of Magnetron Sputtered TiN Coatings Deposited on High Strength Aluminium Alloys, Surf. Coat. Technol., 2004, 177-178, p p399-p40310.1016/j.surfcoat.2003.09.015 ↗
5. T. Burakowski, Surface Engineering of Metals, CRC Press, Boca Raton, 1999
6. V.F. Kosarev, S.V. Klinkov, A.P. Alkhimov, and A.N. Papyrin, On Some Aspects of Gas Dynamics of the Cold Spray Process, J. Therm. Spray Technol., 2003, 12(2), p 265-28110.1361/105996303770348384 ↗
7. H. Assadi, F. Gartner, T. Stoltenhoff, and H. Kreye, Bonding Mechanism in Cold Gas Spraying, Acta Mater., 2003, 51, p 4379-443910.1016/S1359-6454(03)00274-X ↗
8. B.S. DeForce, T.J. Eden, and J.K. Potter, Cold Spray Al-5% Mg Coatings for the Corrosion Protection of Magnesium Alloys, J. Therm. Spray Technol., 2011, 20(6), p 1352-135810.1007/s11666-011-9675-4 ↗
9. D. Dzhurinskiy, E. Maeva, Ev. Leshchinsky, and R.Gr. Maev, Corrosion Protection of Light Alloys Using Low Pressure Cold Spray, J. Therm. Spray Technol., 2012, 21(2), p 304-31310.1007/s11666-011-9729-7 ↗
10. Y. Tao, T. Xiong, C. Sun, H. Jin, H. Du, and T. Li, Effect of α-Al2O3 on the Properties of Cold Sprayed Al/α-Al2O3 Composite Coatings on AZ91D Magnesium Alloy, Appl. Surf. Sci., 2009, 256, p 261-26610.1016/j.apsusc.2009.08.012 ↗
11. H. Koivuluoto, J. Nakki, and P. Vuoristo, Corrosion Properties of Cold-Sprayed Tantalum Coatings, J. Therm. Spray Technol., 2008, 18(1), p 75-8210.1007/s11666-008-9281-2 ↗
12. AFRL/MLLMP—Small Business Innovation Research Phase I Final Report; “Innovative Corrosion Protection Via Cold Spray Kinetic Metallization,” T. Eden, B. Golesich, and M. Sharma (May 2007). Air Force Research Laboratory, Materials and Manufacturing, Wright-Patterson Air Force Base.
13. AFRL/MLLMP—Small Business Innovation Research Phase II Final Report; “Innovative Corrosion Protection Via Cold Spray Kinetic Metallization,” T. Eden, B. Golesich, J. Potter, A. Norris, M. Sharma, and D. Wolfe (April 2010). Air Force Research Laboratory, Materials and Manufacturing, Wright-Patterson Air Force Base.
14. R.C. Dykhuizen and M.F. Smith, Gas Dynamic Principles of Cold Spray, J. Therm. Spray Technol., 1998, 7(2), p 205-21210.1361/105996398770350945 ↗
15. S. Klinkov and V. Kosarev, Measurement of Cold Spray Deposition Efficiency, J. Therm. Spray Technol., 2006, 15(3), p 364-37110.1361/105996306X124365 ↗
16. D.L. Gilmore, R.C. Dykhuizen, R.A. Neiser, T.J. Roemer, and M.F. Smith, Particle Velocity and Deposition Efficiency in the Cold Spray Process, J. Therm. Spray Technol., 1999, 8(4), p 576-58210.1361/105996399770350278 ↗
17. C.W. Ziemian, M.M. Sharma, B.D. Bouffard, T. Nissley, and T.J. Eden, Effect of Substrate Surface Roughening and Cold Spray Coating on the Fatigue Life of AA2024 Specimens, J. Mater. Des., 2014, 54, p 212-22110.1016/j.matdes.2013.08.061 ↗
18. R. Ghelichi and M. Guagliano, Coating by the Cold Spray Process: A State of the Art, Frattura Ed Integrità Strutturale, 2009, 8, p 30-4410.3221/IGF-ESIS.08.03 ↗
19. W. Li, C. Huang, M. Yu, and H. Liao, Investigation on Mechanical Property of Annealed Copper Particles and Cold-Sprayed Copper Coating by a Micro-indentation Testing, Mater. Des., 2013, 46, p 219-22610.1016/j.matdes.2012.10.029 ↗
20. W. Li, C. Zhang, X. Guo, G. Zhang, H. Liao, C. Li et al., Effect of Standoff Distance on Coating Deposition Characteristics in Cold Spraying, Mater. Des., 2008, 29, p 297-30410.1016/j.matdes.2007.02.005 ↗
21. H. Lee, H. Shin, S. Lee, and K. Ko, Effect of Gas Pressure on Al Coatings by Cold Gas Dynamic Spray, Mater. Lett., 2008, 62, p 1579-158110.1016/j.matlet.2007.09.026 ↗
22. B. Jodoin, L. Ajdelsztajn, E. Sansoucy, A. Zúñiga, P. Richer, and E.J. Lavernia, Effect of Particle Size, Morphology, and Hardness on Cold Gas Dynamic Sprayed Aluminum Alloy Coatings, Surf. Coat. Technol., 2006, 201, p 3422-342910.1016/j.surfcoat.2006.07.232 ↗
23. M. Grujicic, C.L. Zhaoa, C. Tonga, W.S. DeRosset, and D. Helfritch, Analysis of the Impact Velocity of Powder Particles in the Cold-Gas Dynamic-Spray Process, Mater. Sci. Eng., 2004, A368, p 222-23010.1016/j.msea.2003.10.312 ↗
24. M. Grujicic, J.R. Saylor, D.E. Beasley, W.S. DeRosset, and D. Helfritch, Computational Analysis of the Interfacial Bonding Between Feed-Powder Particles and the Substrate in the Cold-Gas Dynamic-Spray Process, Appl. Surf. Sci., 2003, 219(3-4), p 21110.1016/S0169-4332(03)00643-3 ↗
25. A.O. Tokarev, Structure of Aluminum Powder Coatings Prepared by Cold Gasdynamic Spraying, Met. Sci. Heat Treat., 1996, 38(3-4), p 136-13910.1007/BF01401446 ↗
26. American Navy Military Standard—MS 2138-A, Metal Sprayed Coatings for Corrosion Protection Aboard Naval Ships (Metric), 1992 (36 pp.).
27. L. Hai-xiang, S. Ming-xian, L. Xiang-bo, and W. Hong-ren, Residual Stress Measurement of Metal Surface, Chin. J. Nonferr. Met., 2010, 20, p 1353-1359
28. H.M. Hawthorne and Y. Xie, An Attempt to Evaluate Cohesion in WC/Co/Cr Coatings by Controlled Scratching, Meccanica, 2001, 36, p 675-68210.1023/A:1016300920619 ↗
29. G. Bae, S. Kumar, S. Yoon, K. Kang, H. Na, H.-J. Kim, and C. Lee, Nanostructure Formation and Its Effects on the Mechanical Properties of Kinetic Sprayed Titanium Coating, Acta Mater., 2009, 57, p 565410.1016/j.actamat.2009.07.061 ↗
30. R.R. Chromik, D. Goldbaum, J. Michael Shockley, S. Yue, E. Irissou, J.-G. Legoux, and N.X. Randall, Modified Ball Bond Shear Test for Determination of Adhesion Strength of Cold Spray Splats, Surf. Coat. Technol., 2010, 205, p 1409-141410.1016/j.surfcoat.2010.07.037 ↗
31. R.S.C. Paredes, S.C. Amico, and A.S.C.M. d’Oliveira, The Effect of Roughness and Pre-heating of the Substrate on the Morphology of Aluminium Coatings Deposited by Thermal Spraying, Surf. Coat. Technol., 2006, 200, p 3049-305510.1016/j.surfcoat.2005.02.200 ↗
32. S. Dosta, M. Couto, and J.M. Guilemany, Cold Spray Deposition of a WC-25Co Cermet onto Al7075-T6 and Carbon Steel Substrates, Acta Mater., 2013, 61(2), p 64310.1016/j.actamat.2012.10.011 ↗