Effects of HVOF Process Parameters on the Properties of Ni-Cr Coatings
Source abstract
Abstract
This research examined the influence of processing parameters on the structure of a Ni-50Cr coating applied by high-velocity oxy-fuel spraying onto stainless steel specimens. This type of coating is normally used as protection against heat and corrosion encountered in power plant and marine boilers, and oil refinery heaters. A statistical design of experiments identified fuel and oxygen flow rates and spraying distance as the most influential parameters controlling the in-flight characteristics of the powder particles prior to impact. The effects of these parameters on the porosity level, oxide content, and microhardness of the coatings were then investigated in more detail. These results indicated that the oxide content and hardness of the coatings were dependent on the gas combustion ratio but not on spraying distance. The porosity level and amount of unmelted particles were reduced at the longest spraying distance.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: High-Temperature Coating Behaviors · Erosion and Abrasive Machining · Coal Combustion and Slurry Processing
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (27)
Show source-provided references
1. D.A. Shifler and L.K. Kohler, Hot Corrosion Resistance and Thermal Stability of High Chromium-Nickel Alloys, Presented at and Published in Proceedings of the NACE International Annual Conference CORROSION/2000, Paper no. 242, NACE, Houston, Texas, 2000
2. “Standard Specification for Casting, Chromium-Nickel Alloys, A560,” Annual Book of ASTM Standards, ASTM, 2000
3. J.R. Davis, Ed., Heat-Resistant Materials: ASM Specialty Handbook, ASM, Materials Park, OH, 1997, p 383-384
4. H.L. Holland, Practical Experience with Countering Metal Dusting in a Methane Reforming Unit, Presented at and Published in Proceedings of the NACE International Annual Conference CORROSION/2001, Paper No. 1385, NACE, Houston, TX, 2001
5. T. Sundararajan, S. Kuroda, and F. Abe, Effect of Thermal Spray on the Microstructure and Adhesive Strength of High-Velocity Oxy-Fuel-Sprayed Ni-Cr Coatings on 9Cr-1Mo Steel, Metall. Mater. Trans. A, 2004, 35(10), p 3187-319910.1007/s11661-004-0063-2 ↗
6. T.S. Sidhu, S. Prakash, and R.D. Agrawal, Studies on the Properties of High-Velocity Oxy-Fuel Thermal Spray Coatings for Higher Temperature Applications, Mater. Sci., 2005, 41(6), p 805-82310.1007/s11003-006-0047-z ↗
7. E. Turunen, “Diagnostic Tools for HVOF Process Optimization,” Ph.D. Thesis, Helsinki University of Technology, 2005
8. D. Cheng, Q. Xu, E.J. Lavernia, and G. Trapaga, The Effect of Particle Size and Morphology on the In-Flight Behavior of Particles During High-Velocity Oxy-Fuel Thermal Spraying, Metall. Mater. Trans., 2001, B32(3), p 525-53510.1007/s11663-001-0037-3 ↗
9. M.A. Uusitalo, P.M.J. Vuoristo, and T.A. Mäntylä, High Temperature Corrosion of Coatings and Boiler Steels in Reducing Chlorine-Containing Atmosphere, Surf. Coat. Technol., 2002, 161(2-3), p 275-28510.1016/S0257-8972(02)00472-3 ↗
10. T. Keller, W. Wagner, J. Ilavsky, J. Pisacka, G. Barbezat, and P. Fiala, Microstructure-Property Relationships and Cross-Property-Correlations of Thermal Sprayed Ni-Alloy Coatings, Thermal Spray 2001: New Surfaces for a New Millennium, C.C. Berndt, K.A. Khor, and E.F. Lugscheider, Ed., May 28-30, 2001 (Singapore), ASM International, 2001, p 643-65210.31399/asm.cp.itsc2001p0643 ↗
11. J.R. Davis, Ed., Handbook of Thermal Spray Technology, Thermal Spray Society, ASM International, OH, 2004, p 338
12. F. Azarmi, T.W. Coyle, and J. Mostaghimi, Optimization of Atmospheric Plasma Spray Process Parameters using a Design of Experiment for Alloy 625 coatings, J. Therm. Spray Tech., 2008, 17(1), p 144-15510.1007/s11666-007-9142-4 ↗
13. P. Fauchais, A. Vardelle, and B. Dussoubs, Quo Vadis Thermal Spraying?, J. Therm. Spray Tech., 2001, 10(1), p 44-6610.1361/105996301770349510 ↗
14. H. Zhang, X.Y. Wang, L.L. Zheng, and X.Y. Jiang, Studies of Splat Morphology and Rapid Solidification During Thermal Spraying, Int. J. Heat Mass Trans., 2001, 44(24), p 4579-459210.1016/S0017-9310(01)00109-0 ↗
15. J. Saaedi, T.W. Coyle, S. Mirdamadi, H. Arabi, and J. Mostaghimi, Phase Formation in a Ni-50Cr HVOF Coating, Surf. Coat. Technol., 2008, 202(24), p 5804-581110.1016/j.surfcoat.2008.05.056 ↗
16. R.K. Roy, Chapter 6, A Primer on the Taguchi Method, Society of Manufacturing Engineers (Dearborn, MI), 1990, p 100-125
17. V. Higuera, F.J. Belzunce, A. Carriles, and S. Poveda, Influence of the Thermal-Spray Procedure on the Properties of a Nickel-Chromium Coating, J. Mater. Sci., 2002, 37(3), p 649-65410.1023/A:1013742213115 ↗
18. E. Lugscheider, C. Herbst, and L. Zhao, Parameter studies on high-velocity oxy-fuel spraying of MCrAlY coatings, Surf. Coat. Technol., 1998, 108-109(1-3), p 16-2310.1016/S0257-8972(98)00630-6 ↗
19. A.D. Hewitt, Technology of Oxy-Fuel Gas Processes; Part 2: Comparative Combustion Properties of Fuel Gases, Weld. Met. Fab., 1972, 40, p 382-390
20. H.H. Tawfik and F. Zimmerman, Mathematical Modeling of the Gas and Powder Flow in HVOF Systems, J. Therm. Spray Technol., 1997, 6(3), p 345-35210.1007/s11666-997-0069-6 ↗
21. M. Li and P.D. Christofides, Multi-Scale Modeling and Analysis of an Industrial HVOF Thermal Spray Process, Chem. Eng. Sci., 2005, 60, p 3649-366910.1016/j.ces.2005.02.043 ↗
22. C.M. Hackett and G.S. Settles, Turbulent Mixing of the HVOF Thermal Spray and Coating Oxidation, Thermal Spray Industrial Applications, C.C. Bernt and S. Sampath, Ed., ASM Intentional, Boston, OH, USA, 1994, p 307-312
23. R.A. Neiser, M.F. Smith, and R.C. Dykhuizen, Oxidation in Wire HVOF-Sprayed Steel, J. Therm. Spray Technol., 1998, 7(4), p 537-54510.1361/105996398770350765 ↗
24. K. Dobler, H. Kreye, and R. Schwetzke, Oxidation of Stainless Steel in the High Velocity Oxy-Fuel Process, J. Therm. Spray Technol., 2000, 9(3), p 407-41310.1361/105996300770349872 ↗
25. K. Korpiola, “High Temperature Oxidation of Metal, Alloy and Cermet Powders in HVOF Spraying Process,” Ph.D. Thesis, Helsinki University of Technology, 2004, p 81
26. J. He, M. Ice, and E. Lavernia, Particle Melting Behavior During High-Velocity Oxygen Fuel Thermal Spraying, J. Therm. Spray Technol., 2001, 10(1), p 83-9310.1361/105996301770349547 ↗
27. J.F. Li, H.L. Liao, C.X. Ding, and C. Coddet, Optimizing the Plasma Spray Process Parameters of Yttria Stabilized Zirconia Coatings Using a Uniform Design of Experiments, J. Mater. Process. Technol., 2005, 160(1), p 34-4210.1016/j.jmatprotec.2004.02.039 ↗