journal article·2019-08Open access

Pores Structure Change Induced by Heat Treatment in Cold-Sprayed Ti6Al4V Coating

Hongxia Zhou, Chengxin Li, Hao Yang, Xiaotao Luo, Guanjun Yang, Wenya Li, Tanvir Hussain, Changjiu Li

Abstract

In this study, the evolution of pores structure in cold-sprayed Ti6Al4V coating (TC4) was analyzed before and after 600-1100 °C heat treatment. It was found that almost no change happened to pores under the heat treatment temperature below 600 °C. When the heat treatment temperature was increased to 700 °C, the coating recrystallized, and pores turned to spheroid and healed because of the “bridging” effect. Some of the pores coarsened after 800 °C and 900 °C heat treatment. This kind of phenomenon grew severer when the heat treatment temperature increased to 1000 °C and 1100 °C. On the whole, with the increment of temperature, for the coating prepared at relatively low temperature, apparent porosity measured by image analysis method tended to go down first and then up, but it decreased all the time for the coating prepared at relatively high temperature. The reason for this phenomenon was contributed to the bonding state of particles in the coating. Only when there were fewer weakly bonded interfaces, the detachment between the particle interfaces which may be caused by release of residual stress did not occur, and there was no pores expansion and internal connectivity, so the porosity continuously decreased.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: High-Temperature Coating Behaviors · Nuclear Materials and Properties · Metal Alloys Wear and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (62)

Show source-provided references
1. H. Assadi, F. Gartner, T. Stoltenhoff, and H. Kreye, Bonding Mechanism in Cold Gas Spraying, Acta Mater., 2003, 51(15), p 4379-439410.1016/S1359-6454(03)00274-X ↗
2. T. Stoltenhoff, C. Borchers, F. Gartner, and H. Kreye, Microstructures and Key Properties of Cold-Sprayed and Thermally Sprayed Copper Coatings, Surf. Coat. Technol., 2006, 200(16–17), p 4947-496010.1016/j.surfcoat.2005.05.011 ↗
3. D.L. Gilmore, R.C. Dykhuizen, R.A. Neiser, T.J. Roemer, and M.F. Smith, Particle Velocity and Deposition Efficiency in the Cold Spray Process, J. Therm. Spray Technol., 1999, 8(4), p 576-58210.1361/105996399770350278 ↗
4. T. Hussain, D.G. McCartney, P.H. Shipway, and D. Zhang, Bonding Mechanisms in Cold Spraying: The Contributions of Metallurgical and Mechanical Components, J. Therm. Spray Technol., 2009, 18(3), p 364-37910.1007/s11666-009-9298-1 ↗
5. M. Fukumoto, H. Wada, K. Tanabe, M. Yamada, E. Yamaguchi, A. Niwa, M. Sugimoto, and M. Izawa, Effect of Substrate Temperature on Deposition Behavior of Copper Particles on Substrate Surfaces in the Cold Spray Process, J. Therm. Spray Technol., 2007, 16(5–6), p 643-65010.1007/s11666-007-9121-9 ↗
6. P. Jakupi, P.G. Keech, I. Barker, S. Ramamurthy, R.L. Jacklin, D.W. Shoesmith, and D.E. Moser, Characterization of Commercially Cold Sprayed Copper Coatings and Determination of the Effects of Impacting Copper Powder Velocities, J. Nucl. Mater., 2015, 466, p 1-1110.1016/j.jnucmat.2015.07.001 ↗
7. W.-Y. Li, H. Liao, C.-J. Li, H.-S. Bang, and C. Coddet, Numerical Simulation of Deformation Behavior of Al Particles Impacting on Al Substrate and Effect of Surface Oxide Films on Interfacial Bonding in Cold Spraying, Appl. Surf. Sci., 2007, 253(11), p 5084-509110.1016/j.apsusc.2006.11.020 ↗
8. T. Wojdat, M. Winnicki, M. Rutkowska-Gorczyca, S. Krupiński, and K. Kubica, Soldering Aluminium to Copper with the Use of Interlayers Deposited by Cold Spraying, Arch. Civil Mech. Eng., 2016, 16(4), p 835-84410.1016/j.acme.2016.06.002 ↗
9. C.-J. Li, W.-Y. Li, and Y.-Y. Wang, Formation of Metastable Phases in Cold-Sprayed Soft Metallic Deposit, Surf. Coat. Technol., 2005, 198(1–3), p 469-47310.1016/j.surfcoat.2004.10.063 ↗
10. X.-T. Luo, Y.-K. Wei, Y. Wang, and C.-J. Li, Microstructure and Mechanical Property of Ti and Ti6Al4V Prepared by an In Situ Shot Peening Assisted Cold Spraying, Mater. Des., 2015, 85, p 527-53310.1016/j.matdes.2015.07.015 ↗
11. N.W. Khun, A.W.Y. Tan, K.J.W. Bi, and E. Liu, Effects of Working Gas on Wear and Corrosion Resistances of Cold Sprayed Ti-6Al-4V Coatings, Surf. Coat. Technol., 2016, 302, p 1-1210.1016/j.surfcoat.2016.05.052 ↗
12. M.V. Vidaller, A. List, F. Gaertner, T. Klassen, S. Dosta, and J.M. Guilemany, Single Impact Bonding of Cold Sprayed Ti-6Al-4V Powders on Different Substrates, J. Therm. Spray Technol., 2015, 24(4), p 644-65810.1007/s11666-014-0200-4 ↗
13. A. Chaudhuri, Y. Raghupathy, D. Srinivasan, S. Suwas, and C. Srivastava, Microstructural Evolution of Cold-Sprayed Inconel 625 Superalloy Coatings on Low Alloy Steel Substrate, Acta Mater., 2017, 129, p 11-2510.1016/j.actamat.2017.02.070 ↗
14. P. Cavaliere, A. Silvello, N. Cinca, H. Canales, S. Dosta, I. Garcia Cano, and J.M. Guilemany, Microstructural and Fatigue Behavior of Cold Sprayed Ni-based Superalloys Coatings, Surf. Coat. Technol., 2017, 324, p 390-40210.1016/j.surfcoat.2017.06.006 ↗
15. R. Singh, K.H. Rauwald, E. Wessel, G. Mauer, S. Schruefer, A. Barth, S. Wilson, and R. Vassen, Effects of Substrate Roughness and Spray-Angle on Deposition Behavior of Cold-Sprayed Inconel 718, Surf. Coat. Technol., 2017, 319, p 249-25910.1016/j.surfcoat.2017.03.072 ↗
16. A.R. Toibah, M. Sato, M. Yamada, and M. Fukumoto, Cold-Sprayed TiO2 Coatings from Nanostructured Ceramic Agglomerated Powders, Mater. Manuf. Processes, 2016, 31(11), p 1527-153410.1080/10426914.2015.1090587 ↗
17. K. Ravi, Y. Ichikawa, K. Ogawa, T. Deplancke, O. Lame, and J.-Y. Cavaille, Mechanistic Study and Characterization of Cold-Sprayed Ultra-High Molecular Weight Polyethylene-Nano-Ceramic Composite Coating, J. Therm. Spray Technol., 2015, 25(1–2), p 160-169
18. G.-R. Li and L.-S. Wang, Durable TBCs with Self-Enhanced Thermal Insulation Based on Co-Design on Macro-and Microstructure. Appl. Surf. Sci., 2019, 483, p 472-48010.1016/j.apsusc.2019.03.309 ↗
19. C.-J. Li and W.-Y. Li, Deposition Characteristics of Titanium Coating in Cold Spraying, Surf. Coat. Technol., 2003, 167(2–3), p 278-28310.1016/S0257-8972(02)00919-2 ↗
20. T. Marrocco, D.G. McCartney, P.H. Shipway, and A.J. Sturgeon, Production of Titanium Deposits by Cold-Gas Dynamic Spray: Numerical Modeling and Experimental Characterization, J. Therm. Spray Technol., 2006, 15(2), p 263-27210.1361/105996306X108219 ↗
21. B.N. Kim, K. Hiraga, K. Morita, H. Yoshida, and H. Zhang, Diffusive Model of Pore Shrinkage in Final-Stage Sintering Under Hydrostatic Pressure, Acta Mater., 2011, 59(10), p 4079-408710.1016/j.actamat.2011.03.032 ↗
22. G. Sundararajan, N.M. Chavan, and S. Kumar, The Elastic Modulus of Cold Spray Coatings: Influence of Inter-Splat Boundary Cracking, J. Therm. Spray Technol., 2013, 22(8), p 1348-135710.1007/s11666-013-0034-5 ↗
23. T. Hussain, D.G. McCartney, P.H. Shipway, and T. Marrocco, Corrosion Behavior of Cold Sprayed Titanium Coatings and Free Standing Deposits, J. Therm. Spray Technol., 2010, 20(1–2), p 260-274
24. M.A. Garrido, P. Sirvent, and P. Poza, Evaluation of Mechanical Properties of Ti6Al4V Cold Sprayed Coatings, Surf. Eng., 2017, 34(5), p 399-40610.1080/02670844.2017.1398442 ↗
25. W.-Y. Li, C. Zhang, X. Guo, J. Xu, C.-J. Li, H. Liao, C. Cocidet, and K.A. Khor, Ti and Ti-6Al-4V Coatings by Cold Spraying and Microstructure Modification by Heat Treatment, Adv. Eng. Mater., 2007, 9(5), p 418-42310.1002/adem.200700022 ↗
26. P. Vo, E. Irissou, J.G. Legoux, and S. Yue, Mechanical and Microstructural Characterization of Cold-Sprayed Ti-6Al-4V After Heat Treatment, J. Therm. Spray Technol., 2013, 22(6), p 954-96410.1007/s11666-013-9945-4 ↗
27. I.C. Noyan and J.B. Cohen, Determination of strain and stress fields by diffraction methods, Residual Stressed., Springer, Berlin, 1987, p 117-163
28. Y.-C. Yang and E. Chang, Influence of Residual Stress on Bonding Strength and Fracture of Plasma-Sprayed Hydroxyapatite Coatings on Ti-6Al-4V Substrate, Biomaterials, 2001, 22(13), p 1827-183610.1016/S0142-9612(00)00364-1 ↗
29. S.H. Zahiri, D. Fraser, and M. Jahedi, Recrystallization of Cold Spray-Fabricated CP Titanium Structures, J. Therm. Spray Technol., 2008, 18(1), p 16-2210.1007/s11666-008-9212-2 ↗
30. H.R. Salimijazi, Z.A. Mousavi, M.A. Golozar, J. Mostaghimi, and T. Coyle, Kinetic Study of the Solid-State Transformation of Vacuum-Plasma-Sprayed Ti-6Al-4V Alloy, J. Therm. Spray Technol., 2013, 23(1–2), p 31-39
31. R. Huang, M. Sone, W. Ma, and H. Fukanuma, The Effects of Heat Treatment on the Mechanical Properties of Cold-Sprayed Coatings, Surf. Coat. Technol., 2015, 261, p 278-28810.1016/j.surfcoat.2014.11.017 ↗
32. B. Al-Mangour, R. Mongrain, E. Irissou, and S. Yue, Improving the Strength and Corrosion Resistance of 316L Stainless Steel for Biomedical Applications Using Cold Spray, Surf. Coat. Technol., 2013, 216, p 297-30710.1016/j.surfcoat.2012.11.061 ↗
33. N. Kang, P. Coddet, H. Liao, and C. Coddet, Cold Gas Dynamic Spraying of a Novel Micro-Alloyed Copper: Microstructure, Mechanical Properties, J. Alloy. Compd., 2016, 686, p 399-40610.1016/j.jallcom.2016.06.037 ↗
34. S. Kumar and A.A. Rao, Influence of Coating Defects on the Corrosion Behavior of Cold Sprayed Refractory Metals, Appl. Surf. Sci., 2017, 396, p 760-77310.1016/j.apsusc.2016.11.022 ↗
35. T. Liu, X.-T. Luo, X. Chen, G.-J. Yang, C.-X. Li, and C.-J. Li, Morphology and Size Evolution of Interlamellar Two-Dimensional Pores in Plasma-Sprayed La 2 Zr 2 O 7 Coatings During Thermal Exposure at 1300 °C, J. Therm. Spray Technol., 2015, 24(5), p 739-74810.1007/s11666-015-0236-0 ↗
36. P. Vo, D. Goldbaum, W. Wong, E. Irissou, J.-G. Legoux, R.R. Chromik, and S. Yue, Cold-Spray Processing of Titanium and Titanium Alloys, Titanium Powder Metallurgy, 2015, p 405-42310.1016/B978-0-12-800054-0.00022-8 ↗
37. W.-Y. Li, C. Yang, and H. Liao, Effect of Vacuum Heat Treatment on Microstructure and Microhardness of Cold-Sprayed TiN Particle-Reinforced Al Alloy-Based Composites, Mater. Des., 2011, 32(1), p 388-39410.1016/j.matdes.2010.06.002 ↗
38. N.W. Khun, A.W.Y. Tan, W. Sun, and E. Liu, Effect of Heat Treatment Temperature on Microstructure and Mechanical and Tribological Properties of Cold Sprayed Ti-6Al-4V Coatings, Tribol. Trans., 2016, 60(6), p 1033-104210.1080/10402004.2016.1244584 ↗
39. C.-J. Li, W.-Y. Li, and H. Liao, Examination of the Critical Velocity for Deposition of Particles in Cold Spraying, J. Therm. Spray Technol., 2006, 15(2), p 212-22210.1361/105996306X108093 ↗
40. F.J. Gil and J.A. Planell, Behaviour of Normal Grain Growth Kinetics in Single Phase Titanium and Titanium Alloys, Mater. Sci. Eng. Struct. Mater. Prop. Microstruct. Process., 2000, 283(1–2), p 17-2410.1016/S0921-5093(00)00731-0 ↗
41. Y.J. Li, X.T. Luo, H. Rashid, and C.J. Li, A new Approach to Prepare Fully Dense Cu with High Conductivities and Anti-Corrosion Performance by Cold Spray, J. Alloys Compd., 2018, 740, p 406-41310.1016/j.jallcom.2017.11.053 ↗
42. A. Singh, G. Singh, and V. Chawla, Influence of Post Coating Heat Treatment on Microstructural, Mechanical and Electrochemical Corrosion Behaviour of Vacuum Plasma Sprayed Reinforced Hydroxyapatite Coatings, J. Mech. Behav. Biomed. Mater., 2018, 85, p 20-3610.1016/j.jmbbm.2018.05.030 ↗
43. R. Ghelichi, S. Bagherifard, D. MacDonald, I. Fernandez-Pariente, B. Jodoin, and M. Guagliano, Experimental and Numerical Study of Residual Stress Evolution in Cold Spray Coating, Appl. Surf. Sci., 2014, 288, p 26-3310.1016/j.apsusc.2013.09.074 ↗
44. Z. Arabgol, H. Assadi, T. Schmidt, F. Gärtner, and T. Klassen, Analysis of Thermal History and Residual Stress in Cold-Sprayed Coatings, J. Therm. Spray Technol., 2014, 23(1–2), p 84-9010.1007/s11666-013-9976-x ↗
45. K. Yang, W. Li, X. Yang, and Y. Xu, Anisotropic Response of Cold Sprayed Copper Deposits, Surf. Coat. Technol., 2018, 335, p 219-22710.1016/j.surfcoat.2017.12.043 ↗
46. V. Luzin, K. Spencer, and M.-X. Zhang, Residual Stress and Thermo-Mechanical Properties of Cold Spray Metal Coatings, Acta Mater., 2011, 59(3), p 1259-127010.1016/j.actamat.2010.10.058 ↗
47. B.R. Sridhar, G. Devananda, K. Ramachandra, and R. Bhat, Effect of Machining Parameters and Heat Treatment on the Residual Stress Distribution in Titanium Alloy IMI-834, J. Mater. Process. Technol., 2003, 139(1–3), p 628-63410.1016/S0924-0136(03)00612-5 ↗
48. K.A. Venkata, S. Kumar, H.C. Dey, D.J. Smith, P.J. Bouchard, and C.E. Truman, Study on the Effect of Post Weld Heat Treatment Parameters on the Relaxation of Welding Residual Stresses in Electron Beam Welded P91 Steel Plates, Procedia Eng., 2014, 86(86), p 223-23310.1016/j.proeng.2014.11.032 ↗
49. P. Dong, S. Song, and J. Zhang, Analysis of Residual Stress Relief Mechanisms in Post-Weld Heat Treatment, Int. J. Press. Vessels Pip., 2014, 122(1), p 6-1410.1016/j.ijpvp.2014.06.002 ↗
50. Y.Q. Ren, P.C. King, Y.S. Yang, T.Q. Xiao, C. Chu, S. Gulizia, and A.B. Murphy, Characterization of Heat Treatment-Induced Pore Structure Changes in Cold-Sprayed Titanium, Mater. Charact., 2017, 132, p 69-7510.1016/j.matchar.2017.08.006 ↗
51. W.L.H.L.C. Coddet, Preparation and Characterization of Porous Titanium and Titanium Alloy by Cold Spraying, Rare Metal Mater. Eng., 2009, 38, p 260-263
52. J.L. Shi and Z.X. Lin, The Flow Characteristics of Hot-Pressing of Beta-AL2O3, Ceram. Int., 1989, 15(2), p 107-11210.1016/0272-8842(89)90022-9 ↗
53. YungChin Yang, Influence of Residual Stress on Bonding Strength of the Plasma-Sprayed Hydroxyapatite Coating After the Vacuum Heat Treatment, Surf. Coat. Technol., 2007, 201(16), p 7187-719310.1016/j.surfcoat.2007.01.027 ↗
54. A.G. Evans, G.B. Crumley, and R.E. Demaray, On the Mechanical Behavior of Brittle Coatings and Layers, Oxid. Met., 1983, 20(5–6), p 193-21610.1007/BF00656841 ↗
55. Y.C. Yang and E. Chang, Influence of Residual Stress on Bonding Strength and Fracture of Plasma-Sprayed Hydroxyapatite Coatings on Ti-6Al-4V Substrate, Biomaterials, 2001, 22(13), p 1827-183610.1016/S0142-9612(00)00364-1 ↗
56. C. Chen, Y. Xie, S. Yin, M.P. Planche, S. Deng, R. Lupoi, and H. Liao, Evaluation of the Interfacial Bonding Between Particles and Substrate in Angular Cold Spray, Mater. Lett., 2016, 173, p 76-7910.1016/j.matlet.2016.03.036 ↗
57. W.Y. Li, C. Zhang, H.T. Wang, X.P. Guo, H.L. Liao, C.J. Li, and C. Coddet, Significant Influences of Metal Reactivity and Oxide Films at Particle Surfaces on Coating Microstructure in Cold Spraying, Appl. Surf. Sci., 2007, 253(7), p 3557-356210.1016/j.apsusc.2006.07.063 ↗
58. S.V. Klinkov, V.F. Kosarev, and M. Rein, Cold Spray Deposition: Significance of Particle Impact Phenomena, Aerosp. Sci. Technol., 2005, 9(7), p 582-59110.1016/j.ast.2005.03.005 ↗
59. B.B. Khina, I. Solpan, and G.F. Lovshenko, Modelling Accelerated Solid-State Diffusion Under the Action of Intensive Plastic Deformation, J. Mater. Sci., 2004, 39(16–17), p 5135-513810.1023/B:JMSC.0000039197.36924.9c ↗
60. X.T. Luo, C.X. Li, F.L. Shang, G.J. Yang, Y.Y. Wang, and C.J. Li, High Velocity Impact Induced Microstructure Evolution During Deposition of Cold Spray Coatings: A Review, Surf. Coat. Technol., 2014, 254(10), p 11-2010.1016/j.surfcoat.2014.06.006 ↗
61. A.L. Ruoff, Enhanced Diffusion During Plastic Deformation by Mechanical Diffusion, J. Appl. Phys., 1967, 38(10), p 3999-400310.1063/1.1709056 ↗
62. J.A. Varela, O.J. Whittemore, and E. Longo, Pore Size Evolution During Sintering of Ceramic Oxides, Ceram. Int., 1990, 16(3), p 177-18910.1016/0272-8842(90)90053-I ↗