journal article·2017-10

Predicting the Effects of Powder Feeding Rates on Particle Impact Conditions and Cold Spray Deposited Coatings

Ozan C. Ozdemir, Christian A. Widener, Michael J. Carter, Kyle W. Johnson

Publisher page

Abstract

As the industrial application of the cold spray technology grows, the need to optimize both the cost and the quality of the process grows with it. Parameter selection techniques available today require the use of a coupled system of equations to be solved to involve the losses due to particle loading in the gas stream. Such analyses cause a significant increase in the computational time in comparison with calculations with isentropic flow assumptions. In cold spray operations, engineers and operators may, therefore, neglect the effects of particle loading to simplify the multiparameter optimization process. In this study, two-way coupled (particle–fluid) quasi-one-dimensional fluid dynamics simulations are used to test the particle loading effects under many potential cold spray scenarios. Output of the simulations is statistically analyzed to build regression models that estimate the changes in particle impact velocity and temperature due to particle loading. This approach eases particle loading optimization for more complete analysis on deposition cost and time. The model was validated both numerically and experimentally. Further numerical analyses were completed to test the particle loading capacity and limitations of a nozzle with a commonly used throat size. Additional experimentation helped document the physical limitations to high-rate deposition.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: High-Temperature Coating Behaviors · Particle Dynamics in Fluid Flows · Fluid Dynamics and Heat Transfer

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (49)

Show source-provided references
1. V. Champagne, The Cold Spray Materials Deposition Process: Fundamentals and Applications, Woodhead Publishing Limited, Cambridge, 2007
2. A. Papyrin, V. Kosarev, S. Klinkov, A. Alkimov, and V. Fomin, Cold Spray Technology, Elsevier, Amsterdam, 2007
3. J. Villafuerte, Modern Cold Spray: Materials, Process, and Applications, Springer, Cham, 201510.1007/978-3-319-16772-5 ↗
4. E. Irissou, F. Ilinca, W. Wong, J.G. Legoux, S. Yue, Investigation on the Effect of Helium-to-Nitrogen Ratio as Propellent Gas Mixture on the Processing of Titanium Coating using Cold Gas Dynamic Spray, International Thermal Spray Conference, B.R. Marple, A. Agarwal, M.M. Hyland, Y.C. Lau, C.J. Li, R.S. Lima, and A. McDonal Eds., September 27-29, 2011 (Hamburg, Germany), DVS10.31399/asm.cp.itsc2011p0066 ↗
5. O.C. Ozdemir, C.A. Widener, D. Helfritch, and F. Delfanian, Estimating the Effect of Helium and Nitrogen Mixing on Deposition Efficiency in Cold Spray, J. Therm. Spray Technol., 2016, 25(4), p 660-67110.1007/s11666-016-0394-8 ↗
6. H. Assadi, F. Gartner, T. Stoltenhoff, and H. Kreye, Bonding Mechanism in Cold Gas Spraying, Acta Mater., 2003, 51, p 4379-439410.1016/S1359-6454(03)00274-X ↗
7. T. Schmidt, H. Assadi, F. Gartner, H. Richter, T. Stoltenhoff, H. Kreye, and T. Klassen, From Particle Acceleration to Impact and Bonding in Cold Spraying, J. Therm. Spray Technol., 2009, 18(5-6), p 794-80810.1007/s11666-009-9357-7 ↗
8. M.R. Rokni, C.A. Widener, and V.R. Champagne, Microstructural Stability of Ultrafine Grained Cold Sprayed 6061 Aluminum Alloy, Appl. Surf. Sci., 2014, 290, p 482-48910.1016/j.apsusc.2013.11.127 ↗
9. F.Z. Shaikh, H.D. Blair, R.J. Tabaczynski, and T.Y. Pan, Gas-Dynamic Cold Spraying Lining for Aluminum Engine Block Cylinders, ed., U.S.P.a.T. Office, Ed., 2002
10. M. Faccoli, G. Cornacchia, D. Maestrini, G.P. Marconi, and R. Roberti, Cold Spray Repair of Martensitic Stainless Steel Components, J. Therm. Spray Technol., 2014, 23(8), p 1270-128010.1007/s11666-014-0129-7 ↗
11. M. Fukumoto, M. Mashiko, M. Yamada, and E. Yamaguchi, Deposition Behavior of Copper Fine Particles onto Flat Substrate Surface in Cold Spraying, J. Therm. Spray Technol., 2009, 19(1-2), p 89-9410.1007/s11666-009-9426-y ↗
12. J.M. Hoey, M.J. Robinson, and R.A. Sailer, Micro Cold Spray Printed Top Metallization Layer for Solar Cells, 2014 IEEE 40th Photovoltaic Specialist Converence (Denver, CO), Institute of Electrical and Electronics Engineers Inc., 201410.1109/PVSC.2014.6925435 ↗
13. D.Y. Kim, J.J. Park, J.G. Lee, D. Kim, S.J. Tark, S. Ahn, J.H. Yun, J. Gwak, K.H. Yoon, S. Chandra, and S.S. Yoon, Cold Spray Deposition of Copper Electrodes on Silicon and Glass Substrates, J. Therm. Spray Technol., 2013, 22(7), p 1092-110210.1007/s11666-013-9953-4 ↗
14. F. Raletz, M. Vardelle, and G. Ezo’o, Critical Particle Velocity Under Cold Spray Conditions, Surf. Coat. Technol., 2006, 201, p 1942-194710.1016/j.surfcoat.2006.04.061 ↗
15. K. Binder, J. Gottschalk, M. Kollenda, M. Gartner, and T. Klassen, Influence of Impact Angle and Gas Temperature on Mechanical Properties of Titanium Cold Spray Deposits, J. Therm. Spray Technol., 2010, 20(1-2), p 234-24210.1007/s11666-010-9557-1 ↗
16. D.K. Christoullis, S. Guetta, V. Guipont, and M. Jeandin, The Influence of the Substrate on the Deposition of Cold-Sprayed Titanium: An Experimental and Numerical Study, J. Therm. Spray Technol., 2010, 20(3), p 523-53310.1007/s11666-010-9608-7 ↗
17. T. Marrocco, D.G. McCartney, P.H. Shipway, and A.J. Sturgeon, Production of Titanium Deposits by Cold Gas Dynamic Spray: Numerical Modeling and Experimental Characterization, J. Therm. Spray Technol., 2006, 15(2), p 263-27210.1361/105996306X108219 ↗
18. M.R. Rokni, C.A. Widener, O.C. Ozdemir, and G.A. Crawford, Microstructure and Mechanical Properties of Cold Sprayed 6061 Al in As-Sprayed and Heat Treated Condition, Surf. Coat. Technol., 2017, 309, p 641-65010.1016/j.surfcoat.2016.12.035 ↗
19. H. Assadi, H. Kreye, F. Gartner, and T. Klassen, Cold Spraying—A Materials Perspective, Acta Mater., 2016, 116(1), p 382-40710.1016/j.actamat.2016.06.034 ↗
20. R. Drehmann, T. Grund, T. Lampke, B. Wielage, K. Manygoats, T. Schucknecht, and D. Rafaja, Splat Formation and Adhesion Mechanisms of Cold Gas-Sprayed Al Coatings on Al2O3 Substrates, J. Therm. Spray Technol., 2013, 23(1-2), p 68-7510.1007/s11666-013-9966-z ↗
21. M. Gardon, A. Latorre, M. Torrell, S. Dosta, J. Fernandez, and J.M. Guilemany, Cold Gas Spray Titanium Coatings onto a Biocompatible Polymer, Mater. Lett., 2013, 106, p 97-9910.1016/j.matlet.2013.04.115 ↗
22. R. Lupoi and W. O’Neill, Deposition of metallic coatings on polymer surfaces using cold spray, Surf. Coat. Technol., 2010, 205, p 2167-217310.1016/j.surfcoat.2010.08.128 ↗
23. A. Ganesan, J. Affi, M. Yamada, and M. Fukumoto, Bonding Behavior Studies of Cold Sprayed Copper Coating on the PVC Polymer Substrate, Surf. Coat. Technol., 2012, 207, p 262-26910.1016/j.surfcoat.2012.06.086 ↗
24. M. Winnicki, A. Malachowska, T. Piwowarczyk, M. Rutkowska-Gorczyca, and A. Ambroziak, The Bond Strength of Al + Al2O3 Cermet Coatings Deposited by Low-Pressure Cold Spraying, Arch. Civ. Mech. Eng., 2016, 16(4), p 743-75210.1016/j.acme.2016.04.014 ↗
25. H. Assadi, T. Schmidt, H. Richter, J.-O. Kliemann, K. Binder, F. Gartner, T. Klassen, and H. Kreye, On Parameter Selection in Cold Spraying, J. Therm. Spray Technol., 2011, 20(6), p 1161-117610.1007/s11666-011-9662-9 ↗
26. J.D. Anderson, Modern Compressible Flow with Historical Perspective, McGraw-Hill Inc., New York, 2012
27. R.C. Dykhuizen and M.F. Smith, Gas Dynamic Principles of Cold Spray, J. Therm. Spray Technol., 1998, 7(2), p 205-21210.1361/105996398770350945 ↗
28. M. Grujicic, J.R. Saylor, D.E. Beasley, W.S. DeRosset, and D. Helfritch, Computational Analysis of the Interfacial Bonding between Feed-Powder Particles and the Substrate in the Cold-Gas Dynamic-Spray Process, Appl. Surf. Sci., 2003, 219, p 211-22710.1016/S0169-4332(03)00643-3 ↗
29. M. Grujicic, C.L. Zhao, C. Tong, W.S. DeRosset, and D. Helfritch, Analysis of the Impact Velocity of Powder Particles in the Cold-Gas Dynamic-Spray Process, Mater. Sci. Eng., A, 2004, 368, p 222-23010.1016/j.msea.2003.10.312 ↗
30. D. Helfritch, V. Champagne, A Model Study of Powder Particle Size Effects in Cold Spray Deposition, ed., U.S.A.R. Laboratory, Ed., 2008
31. B. Jodoin, Cold Spray Nozzle Mach Number Limitation, J. Therm. Spray Technol., 2002, 11(4), p 496-50710.1361/105996302770348628 ↗
32. B. Jodoin, F. Raletz, and M. Vardelle, Cold Spray Modeling and Validation Using an Optical Diagnostic Method, Surf. Coat. Technol., 2006, 200, p 4424-443210.1016/j.surfcoat.2005.02.209 ↗
33. M.C. Meyer, S. Yin, K.A. McDonnell, O. Stier, and R. Lupoi, Feed Rate Effect on Particulate Acceleration in Cold Spray Under Low Stagnation Pressure Conditions, Surf. Coat. Technol., 2016, 304, p 237-24510.1016/j.surfcoat.2016.07.017 ↗
34. K. Taylor, B. Jodoin, and J. Karov, Particle Loading Effect in Cold Spray, J. Therm. Spray Technol., 2005, 15(2), p 273-27910.1361/105996306X108237 ↗
35. J.D.J. Anderson, Computational Fluid Dynamics: The Basics with Applications, McGraw-Hill Inc., New York, 1995
36. R.B. Bird, W.E. Stewart, and E.N. Lightfoot, Transport Phenomena, 2nd ed., Wiley, Hoboken, 2002, p 27, 276, 439
37. J.F. Wendt, Computational Fluid Dynamics: An Introduction, 3rd ed., Springer, Berlin, 200910.1007/978-3-540-85056-4 ↗
38. H. Schlichting, Boundary Layer Theory, 7 ed., F.J. Cerra, Ed., McGraw-Hill Book Company, Inc., New York, 1987, p 596-667
39. A. Bejan, Heat Transfer, Wiley, Hoboken, 1993
40. D.J. Carlson and R.F. Hogland, Particle Drag and Heat Transfer in Rocket Nozzles, AIAA J., 1964, 2(11), p 1980-198410.2514/3.2714 ↗
41. Y.A. Cengel and M.A. Boles, Thermodynamics: An Engineering Approach, 5th ed., McGraw-Hill College, New York, 2006
42. F.M. White, Fluid Mechanics, 7th ed., McGraw-Hill, New York, 2011, p 608-681
43. A. Moridi, S.M. Hassani-Gangaraj, and M. Guagliano, A Hybrid Approach to Determine Critical and Erosion Velocities in the Cold Spray Process, Appl. Surf. Sci., 2013, 273, p 617-62410.1016/j.apsusc.2013.02.089 ↗
44. T. Schmidt, F. Gartner, H. Assadi, and H. Kreye, Development of a Generalized Parameter Window for Cold Spray Deposition, Acta Mater., 2006, 54, p 729-74210.1016/j.actamat.2005.10.005 ↗
45. J.R. Davis, Concise Metals Engineering Data Book, ASM International, Ohio, 1997
46. CSM Evolution: Product Manual, 1st ed., Tecnar Automation Ltd., 2013
47. Standard Guide for Metallographic Preparation of Thermal Sprayed Coatings, E1920-03, ASTM International, 2014
48. M.J.R. Williams, Multiphase Flow Research, Nova Science Publishers Inc., New York, 2009
49. R. Boyer, G.C. Welsch, and E.W. Collings, Materials Properties Handbook: Titanium Alloys, ASM International, Ohio, 1994