journal article·2020-08

Residual Stresses in Cold Spray Additively Manufactured Hollow Titanium Cylinders

Alejandro Vargas-Uscategui, Peter C. King, Mark J. Styles, Michael Saleh, Vladimir Luzin, Kevin Thorogood

Publisher page

Abstract

In cold spray additive manufacturing (CSAM), the severe plastic deformation of the input powder particles leads to an accumulation of residual stresses, the magnitude of which is affected by process conditions. In the current study, the effects of traverse speed and powder feed rate on the residual stress state were investigated in commercially pure titanium cylinders produced by CSAM. Residual stress measurements were made in a grid pattern covering the 2D cross section using the KOWARI neutron diffractometer at ANSTO, Australia, and selected results were validated using the contour method. It was found that the thermal effect was dominant on the residual stress state generating a tensile state near the inner and outer surfaces of the cylinder walls while compressive residual stresses tend to accumulate in the center of the wall. The residual stresses were dominated by thermal stresses at low traverse speed, while peening becomes more critical at high traverse speeds. Increasing the powder feed rate increased the magnitude of the residual stresses. High traverse speeds and low feed rates are beneficial for producing 3D parts by CSAM. However, slow traverse speeds are more detrimental than high feed rates for a given layer thickness.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: High-Temperature Coating Behaviors · Nuclear Materials and Properties · Advanced materials and composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (29)

Show source-provided references
1. A. Papyrin, V. Kosarev, S. Klinkov, A. Alkhimov, and V. Fomin, Cold Spray Technology, Elsevier, Amsterdam, 2007
2. S. Pathak and G. Saha, Development of Sustainable Cold Spray Coatings and 3D Additive Manufacturing Components for Repair/Manufacturing Applications: A Critical Review, Coatings, 2017, 7, p 12210.3390/coatings7080122 ↗
3. A. Green, “Cold Spray Heats Up. https://blog.csiro.au/cold-spray-heats-up/, 2017
4. S.H. Zahiri, C.I. Antonio, and M. Jahedi, Elimination of Porosity in Directly Fabricated Titanium via Cold Gas Dynamic Spraying, J. Mater. Process. Technol., 2009, 209, p 92210.1016/j.jmatprotec.2008.03.005 ↗
5. T. Hussain, Cold Spraying of Titanium: A Review of Bonding Mechanisms, Microstructure and Properties, Key Eng. Mater., 2012, 533, p 5310.4028/www.scientific.net/KEM.533.53 ↗
6. P. Vo, D. Goldbaum, W. Wong, E. Irissou, J.-G. Legoux, R.R. Chromik, and S. Yue, Titanium Powder Metallurgy, Elsevier, Amsterdam, 2015, p 405-42310.1016/B978-0-12-800054-0.00022-8 ↗
7. J. Karthikeyan, The Cold Spray Materials Deposition Process. Woodhead Publishing Series in Metals and Surface Engineering, Woodhead Publishing, New York, 2007, p 62-7110.1533/9781845693787.1.62 ↗
8. J. Villafuerte, Modern Cold Spray, Springer, Cham, 201510.1007/978-3-319-16772-5 ↗
9. P.C. King, S.H. Zahiri, and M. Jahedi, Microstructural Refinement Within a Cold-Sprayed Copper Particle, Metall. Mater. Trans. A Phys. Metall. Mater. Sci., 2009, 40, p 211510.1007/s11661-009-9882-5 ↗
10. V. Lemiale, P.C. King, M. Rudman, M. Prakash, P.W. Cleary, M.Z. Jahedi, and S. Gulizia, Temperature and Strain Rate Effects in Cold Spray Investigated by Smoothed Particle Hydrodynamics, Surf. Coat. Technol., 2014, 254, p 12110.1016/j.surfcoat.2014.05.071 ↗
11. T. Schmidt, F. Gärtner, H. Assadi, and H. Kreye, Development of a Generalized Parameter Window for Cold Spray Deposition, Acta Mater., 2006, 54, p 72910.1016/j.actamat.2005.10.005 ↗
12. M. Hassani-Gangaraj, D. Veysset, V.K. Champagne, K.A. Nelson, and C.A. Schuh, Adiabatic Shear Instability is Not Necessary for Adhesion in Cold Spray, Acta Mater., 2018, 158, p 43010.1016/j.actamat.2018.07.065 ↗
13. V. Luzin, K. Spencer, and M.X. Zhang, Residual Stress and Thermo-mechanical Properties of Cold Spray Metal Coatings, Acta Mater., 2011, 59, p 125910.1016/j.actamat.2010.10.058 ↗
14. V. Luzin, K. Spencer, M.X. Zhang, and N. Matthews, Structure-Properties Relations in High-Pressure Cold-Sprayed Deposits, Mater. Sci. Forum, 2013, 772, p 15510.4028/www.scientific.net/MSF.772.155 ↗
15. V. Luzin, K. Spencer, M. Zhang, N. Matthews, J. Davis, and M. Saleh, Cold-Spray Coatings, Springer, Cham, 2018, p 451-48010.1007/978-3-319-67183-3_16 ↗
16. H. Jahed and R. Ghelichi, Modern Cold Spray, Springer, Cham, 2015, p 225-25210.1007/978-3-319-16772-5_5 ↗
17. D. Boruah, B. Ahmad, T.L. Lee, S. Kabra, A.K. Syed, P. McNutt, M. Doré, and X. Zhang, Evaluation of Residual Stresses Induced by Cold Spraying of Ti-6Al-4V on Ti-6Al-4V Substrates, Elsevier, Amsterdam, 201910.1016/j.surfcoat.2019.06.028 ↗
18. ASTM, ASTM B348 Standard Specification for Titanium and Titanium Alloy Bars and Billets, 2013
19. M.B. Prime, Cross-Sectional Mapping of Residual Stresses by Measuring the Surface Contour After a Cut, J. Eng. Mater. Technol. Trans. ASME, 2001, 123, p 16210.1115/1.1345526 ↗
20. G.S. Schajer, Practical Residual Stress Measurement Methods, Wiley, Chichester, 201310.1002/9781118402832 ↗
21. D.W. Brown, T.M. Holden, B. Clausen, M.B. Prime, T.A. Sisneros, H. Swenson, and J. Vaja, Critical Comparison of Two Independent Measurements of Residual Stress in an Electron-Beam Welded Uranium Cylinder: Neutron Diffraction and the Contour Method, Acta Mater., 2011, 59, p 86410.1016/j.actamat.2010.09.022 ↗
22. ABACUS, ABACUS Documentation, Dassault Systemes, Providence, 2013
23. P. Lurtz, Topology and Porosity Examination of Three-Dimensional Cold Spray Additively Manufactured Titanium Walls and Square Corners, Helmut Schmidt University, Hamburg, 2018
24. M. Faizan-Ur-Rab, S.H. Zahiri, S.H. Masood, M. Jahedi, and R. Nagarajah, PIV Validation of 3D Multicomponent Model for Cold Spray Within Nitrogen and Helium Supersonic Flow Field, J. Therm. Spray Technol., 2017, 26, p 94110.1007/s11666-017-0567-0 ↗
25. J.J. Valencia and P.N. Quested, ASM Handbook, Volume 15: Casting, Vol 15, ASM International, Materials Park, 2008, p 468-482
26. G. Bae, S. Kumar, S. Yoon, K. Kang, H. Na, H.J. Kim, and C. Lee, Bonding Features and Associated Mechanisms in Kinetic Sprayed Titanium Coatings, Acta Mater., 2009, 57, p 565410.1016/j.actamat.2009.07.061 ↗
27. V. Kosarev, S. Klinkov, A. Alkhimov, and A. Papyrin, On Some Aspects of Gas Dynamics of the Cold Spray Process, J. Therm. Spray Technol., 2003, 12, p 26510.1361/105996303770348384 ↗
28. A.N. Ryabinin, E. Irissou, A. McDonald, and J.-G. Legoux, Simulation of Gas-Substrate Heat Exchange During Cold-Gas Dynamic Spraying, Int. J. Therm. Sci., 2012, 56, p 1210.1016/j.ijthermalsci.2012.01.007 ↗
29. O.C. Ozdemir, Q. Chen, S. Muftu, and V.K. Champagne, Modeling the Continuous Heat Generation in the Cold Spray Coating Process, J. Therm. Spray Technol., 2019, 28, p 10810.1007/s11666-018-0794-z ↗