journal article·2025-03Open access

Mechanical Properties of Cobalt Chromium Alloy Manufactured by Direct Energy Deposition Technology

David Smith, Paula Pickett, Theresa Grabowski, Joncy Thorpe, Fardad Azarmi

Journal of Thermal Spray Technology· Volume 34· Issue 2-3

Abstract

Abstract Cobalt chromium (CoCr), a well-known biocompatible material, is additively manufactured using direct energy deposition (DED) technology in this study. This study investigates some important mechanical characteristics of the additively manufactured CoCr using two different numerical simulation methods in addition to mechanical tests and experiments. Mechanical experiments such as hardness, wear, and flexural bending test were conducted on DED-processed samples. All experiments were also conducted on conventionally processed CoCr specimens for comparison purposes. DED-processed CoCr samples exhibited a complex microstructure with a variety of features such as cellular, columnar, and equiaxed grains within their melt pools. While the DED-processed sample had a lower hardness compared to the conventionally processed one, it exhibited a higher wear resistance. The tensile strength obtained from resonance frequency testing was higher for the DED-processed CoCr sample compared to the conventionally fabricated one. The out-of-plane mechanical strength of CoCr samples was measured by conducting flexural bending test, and the conventional sample showed a higher flexural modulus than the DED sample. The bend tests were also numerically simulated using two different finite element analysis (FEA) procedures. The FEA results for the conventionally processed samples are in good agreement with the ones obtained from the experimental flexural bending test. The results of the FEA studies on the DED-processed samples were within 10-20 % of the experimental ones, showing the potential of numerical methods in estimating this property without the need of mechanical testing.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Additive Manufacturing Materials and Processes · Additive Manufacturing and 3D Printing Technologies · High Entropy Alloys Studies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (58)

Show source-provided references
1. S. Natali, A. Brotzu and D. Pilone, Comparison between Mechanical Properties and Structures of a Rolled and a 3D-Printed Stainless Steel, Materials, 2019, 12(23), p 3867. https://doi.org/10.3390/ma1223386710.3390/ma12233867 ↗
2. H. Fayazfar, A Critical Review of Powder-Based Additive Manufacturing of Ferrous Alloys: Process Parameters Microstructure and Mechanical Properties, Mater. Des., 2018, 144, p 98–128. https://doi.org/10.1016/j.matdes.2018.02.01810.1016/j.matdes.2018.02.018 ↗
3. K.S.B. Ribeiro, F.E. Mariani and R.T. Coelho, A Study of Different Deposition Strategies in Direct Energy Deposition (DED) Processes, Procedia Manuf., 2020, 48, p 663–670. https://doi.org/10.1016/j.promfg.2020.05.15810.1016/j.promfg.2020.05.158 ↗
4. U.M. Dilberoglu, B. Gharehpapagh, U. Yaman and M. Dolen, The Role of Additive Manufacturing in the Era of Industry 4.0, Procedia Manuf., 2017, 11, p 545–554. https://doi.org/10.1016/j.promfg.2017.07.14810.1016/j.promfg.2017.07.148 ↗
5. Additive Manufacturing-General Principles-Fundamentals and Vocabulary, ISO/ASTM 52900, Annual Book of ASTM Standards, ASTM, 2021.
6. X. Zhang, W. Li and F. Liou, Additive Manufacturing of Cobalt-based Alloy on Tool Steel by Directed Energy Deposition, Opt. Laser Technol., 2022 https://doi.org/10.1016/j.optlastec.2021.10773810.1016/j.optlastec.2021.107738 ↗
7. W. Yuan, X. He, X. Zhou and Y. Zhu, Hydroxyapatite Nanoparticle-Coated 3D-Printed Porous Ti6Al4V and CoCrMo Alloy Scaffolds and Their Biocompatibility to Human Osteoblasts, J. Nanosci. Nanotechnol., 2018, 18(6), p 4360–4365. https://doi.org/10.1166/jnn.2018.1520710.1166/jnn.2018.15207 ↗
8. S. Acharya, R. Soni, S. Suwas and K. Chatterjee, Additive Manufacturing of Co–Cr Alloys for Biomedical Applications: A Concise Review, J. Mater. Res., 2021, 36(19), p 3746–3760. https://doi.org/10.1557/s43578-021-00244-z10.1557/s43578-021-00244-z ↗
9. I.D. Harris, Additive Manufacturing: A Transformational Advanced Manufacturing Technology, AM&P Tech. Artic., 2012, 170(5), p 25–29. https://doi.org/10.31399/asm.amp.2012-05.p02510.31399/asm.amp.2012-05.p025 ↗
10. A. Takaichi, Microstructures and Mechanical Properties of Co-29Cr-6Mo Alloy Fabricated by Selective Laser Melting Process for Dental Applications, J. Mech. Behav. Biomed. Mater., 2013, 21, p 67–76. https://doi.org/10.1016/j.jmbbm.2013.01.02110.1016/j.jmbbm.2013.01.021 ↗
11. J.M. Chacón, M.A. Caminero, E. García-Plaza and P.J. Núñez, Additive Manufacturing of PLA Structures Using Fused Deposition Modelling: Effect of Process Parameters on Mechanical Properties and their Optimal Selection, Mater. Des., 2017, 124, p 143–157. https://doi.org/10.1016/j.matdes.2017.03.06510.1016/j.matdes.2017.03.065 ↗
12. S. Eshkabilov, I. Ara and F. Azarmi, A Comprehensive Investigation on Application of Machine Learning for Optimization of Process Parameters of Laser Powder Bed Fusion-Processed 316L Stainless Steel”, Int. J. Adv. Manuf. Technol., 2022, 123(7–8), p 2733–2756. https://doi.org/10.1007/s00170-022-10331-y10.1007/s00170-022-10331-y ↗
13. Standard Guide for Directed Energy Deposition of Metals, F 3187, Annual Book of ASTM Standards, ASTM, 2016.
14. N. Shahrubudin, T.C. Lee and R. Ramlan, An Overview on 3D Printing Technology: Technological, Materials, and Applications, Procedia Manuf., 2019 https://doi.org/10.1016/j.promfg.2019.06.08910.1016/j.promfg.2019.06.089 ↗
15. D. Svetlizky, B. Zheng, D.M. Steinberg, J.M. Schoenung, E.J. Lavernia and N. Eliaz, The Influence of Laser Directed Energy Deposition (DED) Processing Parameters for Al5083 Studied by Central Composite Design, J. Market. Res., 2022, 17, p 3157–3171. https://doi.org/10.1016/j.jmrt.2022.02.04210.1016/j.jmrt.2022.02.042 ↗
16. A.D. Lantada, Handbook of Active Materials for Medical Devices Advances and Applications, Pan Stanford Publishing Pte. Ltd., Singapore, 2012.
17. R. Saravanan, R. Hamidon, N.M. Murad and Z.A. Zailani, Machining of Cobalt Chromium Molybdenum (CoCrMo) Alloys: A Review, Intell. Manuf. Mechatron., 2021 https://doi.org/10.1007/978-981-16-0866-7_3610.1007/978-981-16-0866-7_36 ↗
18. M. Liu and M. Kuttolamadom, Characterization of Co-Cr-Mo Alloys Manufacturing via Directed Energy Deposition, Int. Manuf. Sci. Eng. Conf., 2021 https://doi.org/10.1115/MSEC2021-6411110.1115/MSEC2021-64111 ↗
19. A. Chiba, K. Kumagai, N. Nomura and S. Miyakawa, Pin-on-disk Wear Behavior in a Like-on-Like Configuration in a Biological Environment of High Carbon Cast and Low Carbon Forged Co-29Cr-6Mo Alloys, Acta Mater., 2007, 55(4), p 1309–1318. https://doi.org/10.1016/j.actamat.2006.10.00510.1016/j.actamat.2006.10.005 ↗
20. T. Odaira et al., Flexible and Tough Superelastic Co–Cr Alloys for Biomedical Applications, Adv. Mater., 2022 https://doi.org/10.1002/adma.20220230510.1002/adma.202202305 ↗
21. A. Bandyopadhyay, K.D. Traxel, J.D. Avila, I. Mitra, S. Bose and W.M. Keck, CoCr Alloys, Biomater. Sci., 2020 https://doi.org/10.1016/B978-0-12-816137-1.00020-910.1016/B978-0-12-816137-1.00020-9 ↗
22. J.H. Hong and F.Y. Yeoh, Mechanical Properties and Corrosion Resistance of Cobalt-chrome Alloy Fabricated Using Additive Manufacturing, Mater. Today Proc., 2019, 29, p 196–201. https://doi.org/10.1016/j.matpr.2020.05.54310.1016/j.matpr.2020.05.543 ↗
23. L. Tonelli, A. Fortunato and L. Ceschini, CoCr Alloy Processed by Selective Laser Melting (SLM): Effect of Laser Energy Density on Microstructure Surface Morphology, and Hardness, J. Manuf. Process., 2020, 52, p 106–119. https://doi.org/10.1016/j.jmapro.2020.01.05210.1016/j.jmapro.2020.01.052 ↗
24. B. Vandenbroucke and J. Kruth, Selective Laser Melting of Biocompatible Metals for Rapid Manufacturing of Medical Parts, Rapid. Prototyp. J., 2007, 13(4), p 196–203. https://doi.org/10.1108/1355254071077614210.1108/13552540710776142 ↗
25. J. Saini, L. Dowling, D. Trimble and D. Singh, Mechanical Properties of Selective Laser Melted CoCr Alloys: A Review, J. Mater. Eng. Perf., 2021, 30(12), p 8700–8714. https://doi.org/10.1007/s11665-021-06283-110.1007/s11665-021-06283-1 ↗
26. V.D. Sartika, Joining Dissimilar Metal of Ti and CoCrMo Using Directed Energy Deposition, J. Mater. Sci. Technol., 2022, 111, p 99–110. https://doi.org/10.1016/j.jmst.2021.09.03810.1016/j.jmst.2021.09.038 ↗
27. I. Mathoho, E. Akinlabi, N. Arthur and M. Tlotleg, Impact of DED Process Parameters on the Metallurgical Characteristics of 17–4 PH SS Deposited Using DED, CIRP J. Manuf. Sci. Technol., 2020, 31, p 450–458. https://doi.org/10.1016/j.cirpj.2020.07.00710.1016/j.cirpj.2020.07.007 ↗
28. Standard Test Methods for Vickers Hardness and Knoop Hardness of Metallic Materials, E 92, Annual Book of ASTM Standards, ASTM, 2017.
29. M.A. Todd, J. Hunt and I. Todd, Investigation into Using Resonant Frequency Measurements to Predict the Mechanical Properties of Ti-6Al-4V Manufactured by Selective Laser Melting, Sci. Rep., 2019 https://doi.org/10.1038/s41598-019-45696-w10.1038/s41598-019-45696-w ↗
30. Standard Test Method for Dynamic Young’s Modulus, Shear Modulus, and Poisson’s Ratio by Impulse Excitation of Vibration, E 1876, Annual Book of ASTM Standards, ASTM, 2001.
31. Standard Test Methods for Bend Testing of Material for Ductility, E 290, Annual Book of ASTM Standards, ASTM, 2014.
32. C. Balagna, S. Spriano and M.G. Faga, Characterization of Co-Cr-Mo Alloys After a Thermal Treatment for High Wear Resistance, Mater. Sci. Eng. C, 2012, 32(7), p 1868–1877. https://doi.org/10.1016/j.msec.2012.05.00310.1016/j.msec.2012.05.003 ↗
33. A. Masini, F. Šiška, O. Ševeček, Z. Chlup and I. Dlouhý, Elastic Properties of Multi-layered Ceramic Systems for SOCs, Int. J. Appl. Ceram. Technol., 2018, 15(2), p 370–379. https://doi.org/10.1111/ijac.1280110.1111/ijac.12801 ↗
34. A. Saboori, An Investigation on the Effect of Powder Recycling on the Microstructure and Mechanical Properties of AISI 316L Produced by Directed Energy Deposition, Mater. Sci. Eng. A, 2019, 766, p 138360. https://doi.org/10.1016/j.msea.2019.13836010.1016/j.msea.2019.138360 ↗
35. H. Li, M. Wang, D. Lou, W. Xia and X. Fang, Microstructural Features of Biomedical Cobalt–Chromium–Molybdenum (CoCrMo) Alloy from Powder Bed Fusion to Aging Heat Treatment, J. Mater. Sci. Technol., 2020, 45, p 146–156. https://doi.org/10.1016/j.jmst.2019.11.03110.1016/j.jmst.2019.11.031 ↗
36. K.B. Hazlehurst, C.J. Wang and M. Stanford, An Investigation into the Flexural Characteristics of Functionally Graded Cobalt Chrome Femoral Stems Manufactured Using Selective Laser Melting, Mater. Des., 2014, 60, p 177–183. https://doi.org/10.1016/j.matdes.2014.03.06810.1016/j.matdes.2014.03.068 ↗
37. C.T. Wanniarachchi, A. Arjunan, A. Baroutaji and M. Singh, Mechanical Performance of Additively Manufactured Cobalt-Chromium-Molybdenum Auxetic Meta-Biomaterial Bone Scaffolds, J. Mech. Behav. Biomed. Mater., 2022, 134, p 105409. https://doi.org/10.1016/j.jmbbm.2022.10540910.1016/j.jmbbm.2022.105409 ↗
38. A. Barazanchi, K.C. Li, B. Al-Amleh, K. Lyons and J.N. Waddell, Mechanical Properties of Laser-Sintered 3D-Printed Cobalt Chromium and Soft-Milled Cobalt Chromium, Prosthesis, 2020, 2(4), p 313–320. https://doi.org/10.3390/prosthesis204002810.3390/prosthesis2040028 ↗
39. F. Azarmi, T. Coyle and J. Mostaghimi, Young’s Modulus Measurement and Study of the Relationship Between Mechanical Properties and Microstructure of Air Plasma Sprayed Alloy 625, Surf. Coat. Technol., 2009, 203(8), p 1045–1054. https://doi.org/10.1016/j.surfcoat.2008.09.03510.1016/j.surfcoat.2008.09.035 ↗
40. B. Feng, Y. Xin, Z. Sun, H. Yu, J. Wang and Q. Liu, On the Rule of Mixtures for Bimetal Composites, Mater. Sci. Eng. A, 2017, 704, p 173–180. https://doi.org/10.1016/j.msea.2017.08.00510.1016/j.msea.2017.08.005 ↗
41. S. Shaikh, V. Harharan, S. Yadav and B. Murty, CALPHAD and Rule-of-Mixtures: A Comparative Study for Refractory High Entropy Alloys, Intermetallics, 2020, 127, p 106926. https://doi.org/10.1016/j.intermet.2020.10692610.1016/j.intermet.2020.106926 ↗
42. AZoMaterials, An Introduction to Cobalt. Accessed: Dec. 09, 2023. [Online]. Available: https://www.azom.com/article.aspx?ArticleID=596
43. Y. Shi, Metal materials for Additive Manufacturing, Materials for Additive Manufacturing. Academic Press, San Diego, 2021, p 403–59510.1016/B978-0-12-819302-0.00005-5 ↗
44. A. Azidin, Investigation of Mechanical Properties for Open Cellular Structure CoCrMo Alloy Fabricated by Selective Laser Melting Process, IOP Conf. Ser. Mater. Sci. Eng., 2015 https://doi.org/10.1088/1757-899X/100/1/01203310.1088/1757-899X/100/1/012033 ↗
45. I. Hutchings and P. Shipway, Tribology: Friction and Wear of Engineering Materials, Second, Butterworth-Heinemann, Oxford, 2017.
46. E. Rabinowicz, Friction and Wear of Materials, Wiley, Hoboken, 1965.
47. V.L. Popov and R. Pohrt, Adhesive Wear and Particle Emission: Numerical Approach Based on Asperity-Free Formulation of Rabinowicz Criterion, Friction, 2018, 6(3), p 260–273. https://doi.org/10.1007/s40544-018-0236-410.1007/s40544-018-0236-4 ↗
48. I. Ara, X.A. Tangpong and F. Azarmi, Unconventional Wear Characteristics due to Perfect Plasticity in Laser Powder Bed Fusion Processed 316 L Stainless Steel, Int. J. Adv. Manuf. Technol., 2023, 128(7–8), p 3261–3272. https://doi.org/10.1007/s00170-023-12144-z10.1007/s00170-023-12144-z ↗
49. K.-H. Zum Gahr, Microstructure and Wear of Materials: Tribology, Vol 10 Elsevier, Netherlands, 1987.
50. F. Ren, W. Zhu and K. Chu, Fabrication, Tribological and Corrosion Behaviors of Ultra-Fine Grained Co-28Cr-6Mo Alloy for Biomedical Applications, J. Mech. Behav. Biomed. Mater., 2016, 60, p 139–147. https://doi.org/10.1016/j.jmbbm.2015.12.03910.1016/j.jmbbm.2015.12.039 ↗
51. B.V. Krishna, S. Bose and A. Bandyopadhyay, Low Stiffness Porous Ti Structures for Load-Bearing Implants, Acta Biomater., 2007, 3(6), p 997–1006. https://doi.org/10.1016/j.actbio.2007.03.00810.1016/j.actbio.2007.03.008 ↗
52. V.V. Ganesh and N. Chawla, Effect of Particle Orientation Anisotropy on the Tensile Behavior of Metal Matrix Composites: Experiments and Microstructure-based Simulation, Mater. Sci. Eng. A, 2005, 391(1–2), p 342–353. https://doi.org/10.1016/j.msea.2004.09.01710.1016/j.msea.2004.09.017 ↗
53. P. A. Kobryn and S. L. Semiatin, Mechanical Properties of Laser-Deposited Ti-6Al-4V, International Solid Freeform Fabrication Symposium, 2001.
54. S. Dongare, T. E. Sparks, J. Newkirk, and F. Liou, A Mechanical Testing Methodology for Metal Additive Manufacturing Processes Manufacturing Engineering + Mechanical Engineering, Solid Freeform Fabrication Symposium, 2014.
55. J.T. Pacheco, Laser Directed Energy Deposition of AISI 316L Stainless Steel: The Effect of Build Direction on Mechanical Properties in As-Built and Heat-Treated Conditions, Adv. Ind. Manuf. Eng., 2022 https://doi.org/10.1016/j.aime.2022.10007910.1016/j.aime.2022.100079 ↗
56. Y. Ucar and O. Ekren, Effect of Layered Manufacturing Techniques, Alloy Powders, and Layer Thickness on Mechanical Properties of Co-Cr Dental Alloys, J. Prosthet. Dent., 2018 https://doi.org/10.1016/j.prosdent.2017.11.03210.1016/j.prosdent.2017.11.032 ↗
57. M. Zhang, Y. Yang, C. Song, Y. Bai and Z. Xiao, An Investigation Into the Aging Behavior of CoCrMo Alloys Fabricated by Selective Laser Melting, J. Alloys Comp., 2018, 750, p 878–886. https://doi.org/10.1016/j.jallcom.2018.04.0545810.1016/j.jallcom.2018.04.05458 ↗
58. Y. Kajima, A. Takaichi, N. Kittikundecha, T. Nakamoto, T. Kimura, N. Nomura, A. Kawasaki, T. Hanawa, H. Takahashi and N. Wakaayashi, Effect of Heat-Treatment Temperature on Microstructures and Mechanical Properties of Co–Cr–Mo Alloys Fabricated by Selective Laser Melting, Mater. Sci. Eng. A, 2018, 726, p 21–31. https://doi.org/10.1016/j.msea.2018.04.04810.1016/j.msea.2018.04.048 ↗