journal article·2025-03Open access

Nozzle Geometry Evaluation for Cold Spray Applications by Using 3D-CFD Calculations

J. Gutiérrez de Frutos, A. List, S. Nielsen, F. Gärtner, T. Klassen

Journal of Thermal Spray Technology· Volume 34· Issue 2-3

Abstract

Abstract In cold spray applications, optimum process conditions to accelerate particles may vary with different densities of the feedstock. These conditions could depend on the geometry of the spray nozzle, suggesting possible benefits of material-specific nozzle designs. The present study developed a nozzle geometry optimization concept based on three-dimensional computational fluid dynamics (3D-CFD) simulations to provide a specific nozzle design. Applying a design of experiments (DoE) approach, the proposed model seeks an optimal nozzle geometry, using aluminum Al6061 and pure copper with mean particle diameters of 40 µm as examples. Different geometry parameters were varied to reach the highest particle velocities before impact on the substrate, such as the nozzle’s divergent section length, throat cross section, and expansion ratio. The process gas was nitrogen with set stagnation pressure and temperature of 5 MPa and 500 °C, respectively. For high particle impact velocities, the simulation identified the divergent section length as the most influential parameter, followed by the throat cross section. In addition, the results show that the expansion ratio must be carefully tuned to avoid over-expansion of the gas already inside the nozzle, which is detrimental to the particle acceleration.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: High-Temperature Coating Behaviors · Fluid Dynamics and Heat Transfer · Combustion and Detonation Processes

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (32)

Show source-provided references
1. F. Gärtner, A. List, S. Nielsen, H. Wu, Z. Arabgol, L. Wiehler, J. Gutiérrez de Frutos, C. Huang, T. Klassen, M. Lewke, A. Fay, D. Rashikbhai Gabani, J. Gibmeier, A. Pundt, T. Werner, K. Hilgenberg, M. Madia, T. Böllinghaus, L. Holzgaßner, P. Richter, N. Clausing, H. Loitz, P. Keuter, M.t. Baben, M. Steierl, D.E. Schimbäck, T. Rösler, H. Debuch, and T. Gartner, Computerized Refurbishment. 2022.
2. T. Schmidt, H. Assadi, F. Gärtner, H. Richter, T. Stoltenhoff, H. Kreye, and T. Klassen, From Particle Acceleration to Impact and Bonding in Cold Spraying, J. Therm. Spray Tech., 2009, 18(5-6), p 794-808.10.1007/s11666-009-9357-7 ↗
3. T. Schmidt, H. Assadi, F. Gärtner, H. Richter, T. Stoltenhoff, H. Kreye, and T. Klassen, Erratum to: From Particle Acceleration to Impact and Bonding in Cold Spraying, J. Therm. Spray Tech., 2009, 18(5-6), p 1038.10.1007/s11666-009-9399-x ↗
4. C.J. Huang, T. Chen, B.L. Fu, Z.M. Zhang, A. List, L. Wiehler, B. Klusemann, W.Y. Li, F. Gärtner, and T. Klassen, Ductility and Fracture Behavior of Cold Spray Additive Manufactured Zinc, Addit. Manuf., 2024, 89, p 104310.
5. F. Gärtner, T. Stoltenhoff, T. Schmidt, and H. Kreye, The Cold Spray Process and its Potential for Industrial Applications, J. Therm. Spray Tech., 2006, 15(2), p 223-232.10.1361/105996306X108110 ↗
6. H. Assadi, T. Schmidt, H. Richter, J.-O. Kliemann, K. Binder, F. Gärtner, T. Klassen, and H. Kreye, On Parameter Selection in Cold Spraying, J. Therm. Spray Tech., 2011, 20(6), p 1161-1176.10.1007/s11666-011-9662-9 ↗
7. T.B. Mangalarapu, S. Kumar, P. Gandham, and S. Koppoju, Cold Spraying of Al-Aerospace Alloys: Ease of Coating Deposition at High Stagnation Temperatures, Surf. Coat. Technol., 2023, 467, p 129703.10.1016/j.surfcoat.2023.129703 ↗
8. C. Huang, A. List, J. Shen, B. Fu, S. Yin, T. Chen, B. Klusemann, F. Gärtner, and T. Klassen, Tailoring Powder Strengths for Enhanced Quality of Cold Sprayed Al6061 Deposits, Mater. Des., 2022, 215, p 110494.10.1016/j.matdes.2022.110494 ↗
9. I. Dowding, M. Hassani, Y. Sun, D. Veysset, K.A. Nelson, and C.A. Schuh, Particle Size Effects in Metallic Microparticle Impact-Bonding, Acta Mater., 2020, 194, p 40-48.10.1016/j.actamat.2020.04.044 ↗
10. T. Stoltenhoff, H. Kreye, and H.J. Richter, An Analysis of the Cold Spray Process and its Coatings, J. Therm. Spray Tech., 2002, 11(4), p 542-550.10.1361/105996302770348682 ↗
11. A.K. Sharma, A. Vashishtha, D. Callaghan, C. Nolan, S. Bakshi, M. Kamaraj, and R. Raghavendra, Particle acceleration through coaxial co-flow nozzles for cold spray applications. In: Thermal Spray 2022: Proceedings from the International Thermal Spray Conference, 04/05/2022-06/05/2022 (Vienna, Austria), DVS Media GmbH, 2022, p 676-682.
12. C.A. Bernard, H. Takana, O. Lame, K. Ogawa, and J.-Y. Cavaillé, Influence of the Nozzle Inner Geometry on the Particle History During Cold Spray Process, J. Therm. Spray Tech., 2022, 31(6), p 1776-1791.10.1007/s11666-022-01407-y ↗
13. O.Ç. Özdemir, J.M. Conahan, and S. Müftü, Particle Velocimetry Cfd, and the Role of Particle Sphericity in Cold Spray, Coatings, 2020, 10(12), p 1254.10.3390/coatings10121254 ↗
14. O.C. Ozdemir, C.A. Widener, D. Helfritch, and F. Delfanian, Estimating the Effect of Helium and Nitrogen Mixing on Deposition Efficiency in Cold Spray, J. Therm. Spray Tech., 2016, 25(4), p 660-671.10.1007/s11666-016-0394-8 ↗
15. L. Alonso, M.A. Garrido, and P. Poza, An Optimisation Method For the Cold-Spray Process: On the Nozzle Geometry, Mater. Des., 2022, 214, p 110387.10.1016/j.matdes.2022.110387 ↗
16. L. Alonso, M.A. Garrido-Maneiro, and P. Poza, A Study of the Parameters Affecting the Particle Velocity in Cold-Spray: Theoretical Results and Comparison with Experimental Data, Addit. Manuf., 2023, 67, p 103479.
17. A. Mehmood, M. Zunaid, and A.K. Madan, Multi-Objective Optimization and Performance Improvement of Cd Nozzle Design Parameters for Cold Spray Coating Process Using Rsm, Ann and Ga, Mater. Today Commun., 2024, 40, p 109446.10.1016/j.mtcomm.2024.109446 ↗
18. W. Wan, W. Li, D. Wu, Z. Zhang, and B. Ning, 3D Analysis of Gas Flow Behavior and Particle Acceleration Characteristics in Cold Spray Additive Manufacturing Based on Non-axisymmetric Numerical Models, J. Market. Res., 2024, 29, p 1335-1349.
19. S. Yin, M. Meyer, W. Li, H. Liao, and R. Lupoi, Gas Flow Particle Acceleration, and Heat Transfer in Cold Spray: A Review, J. Therm. Spray Tech., 2016, 25(5), p 874-896.10.1007/s11666-016-0406-8 ↗
20. Ansys® Fluent, Release 2021R1, Help System, Ansys Fluent User’s Guide, Ansys, Inc., Canonsburg.
21. C. Gissler, S. Band, A. Peer, M. Ihmsen, and M. Teschner, Generalized Drag Force for Particle-Based Simulations, Comput. Graph., 2017, 69, p 1-11.10.1016/j.cag.2017.09.002 ↗
22. Ansys® Fluent, Release 2021R1, Help System, Ansys Fluent Theory Guide, Ansys, Inc., Canonsburg.
23. R. Clift, J.R. Grace, and M.E. Weber, Bubbles, Drops, and Particles, Academic Press, Cambridge, 1978.
24. E. Loth, J. Tyler Daspit, M. Jeong, T. Nagata, and T. Nonomura, Supersonic and Hypersonic Drag Coefficients for a Sphere, AIAA J., 2021, 59, p 3261-3274.10.2514/1.J060153 ↗
25. R.C. Dykhuizen and M.F. Smith, Gas Dynamic Principles of Cold Spray, J Therm Spray Tech, 1998, 7(2), p 205-212.10.1361/105996398770350945 ↗
26. L.-V. Bouthier and E. Hachem, Analysis and comparisons of various models in cold spray simulations towards high fidelity simulations. 2020.
27. M.S. Malik, Numerical Investigation of Particle Tracking to Achieve High Impact Velocity in Cold Spray, ARME, 2020, 2(4).10.32474/ARME.2020.02.000145 ↗
28. H.-B. Jung, J.-I. Park, S.-H. Park, H.-J. Kim, C. Lee, and J.-W. Han, Effect of the Expansion Ratio and Length Ratio on a Gas-Particle Flow in a Converging-Diverging Cold Spray Nozzle, Met. Mater. Int., 2009, 15(6), p 967-970.10.1007/s12540-009-0967-x ↗
29. W.-Y. Li, H. Liao, G. Douchy, and C. Coddet, Optimal Design of a Cold Spray Nozzle by Numerical Analysis of Particle Velocity and Experimental Validation with 316L Stainless Steel Powder, Mater. Des., 2007, 28(7), p 2129-2137.10.1016/j.matdes.2006.05.016 ↗
30. A. Sova, I. Smurov, M. Doubenskaia, and P. Petrovskiy, Deposition of Aluminum Powder by Cold Spray Micronozzle, Int. J. Adv. Manuf. Technol., 2018, 95(9-12), p 3745-3752.10.1007/s00170-017-1443-2 ↗
31. W.J. Hu, K. Tan, S. Markovych, and X.L. Liu, Study of a Cold Spray Nozzle Throat on Acceleration Characteristics via Cfd, JES, 2021, 8(1), p F19-F24.10.21272/jes.2021.8(1).f3 ↗
32. Y. Meng, H. Saito, C. Bernard, Y. Ichikawa, and K. Ogawa, Optimal Design of a Cold Spray Nozzle for Inner Wall Coating Fabrication by Combining Cfd Simulation and Neural Networks, J. Therm. Spray Tech., 2024, 33(1), p 3-16.10.1007/s11666-024-01716-4 ↗