Flame-Sprayed Ceramic and Metallic Slippery Liquid-Infused Porous and Icephobic Surfaces
Source abstract
Abstract
Abstract This study explores the potential of flame-sprayed (FS) slippery liquid-infused porous surfaces (SLIPS) in addressing challenges associated with icing on structures in different industrial areas. Emphasizing the versatility of flame spraying, metallic (NiCr) and ceramic (Al2O3) coatings were investigated. FS coatings can exhibit high porosity, a crucial requirement for SLIPS. FS-Al2O3 and FS-NiCr exhibited high porosity, 14.8% and 6.7% porosity, respectively. The introduction of lubricating agents, such as silicone oil and epoxy-based sealing agent, enhances coatings’ slipperiness, resulted in icephobic surfaces. These surfaces with reduced ice adhesion strengths were compared to their as-sprayed counterparts. As-sprayed surfaces had high ice adhesion strength (> 100 kPa). SLIPSs achieved lower ice adhesion strength around 63 kPa for the first icing-deicing cycle but could not retain the properties until the last cycle due to oil loss. Even though icephobicity was decreased, porous coating structures were protected by the remaining oil and survived icing-deicing cycles. Therefore, refilling of these structures is possible for long-term icephobicity. Sealed coatings showed stable low ice adhesion strengths around 60 kPa across four icing and deicing cycles, highlighting their potential for practical icephobic applications. Despite challenges in oil retention and durability for SLIPS under harsh icing conditions, flame spraying makes metallic and ceramic SLIPS possible for developing icephobic solutions.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Surface Modification and Superhydrophobicity · Icing and De-icing Technologies · Flame retardant materials and properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (43)
Show source-provided references
1. B.C. Casqueiro, I. Trigo, and M. Belo-Pereira, Characterization of Icing Conditions using Aircraft Reports and Satellite Data, Atmos. Res., 2023, 293, p 106884–106884. https://doi.org/10.1016/j.atmosres.2023.10688410.1016/j.atmosres.2023.106884 ↗
2. Y. Boluk, Transportation Development Centre (Canada), and Canadian Air Transportation Administration Civil Aviation Branch, “Adhesion of Freezing Precipitates to Aircraft Surfaces,” ([Montreal]), [Transportation Development Centre], (1996)
3. O. Parent and A. Ilinca, Anti-Icing and de-Icing Techniques for Wind Turbines: Critical Review, Cold Reg. Sci. Technol., 2011, 65(1), p 88–96.10.1016/j.coldregions.2010.01.005 ↗
4. A. Ilinca, Analysis, and Mitigation of Icing Effects on Wind Turbines, Wind Turbines, I. Al-Bahadly, (Ed.), (Rijeka), (IntechOpen, 2011), p Ch. 8, https://doi.org/10.5772/1548410.5772/15484 ↗
5. J.L. Laforte, M.A. Allaire, and J. Laflamme, State-of-the-Art on Power Line de-Icing, Atmos. Res., 1998, 46(1–2), p 143–158.10.1016/S0169-8095(97)00057-4 ↗
6. N.R. Nusantika, X. Hu,, and J. Xiao, Improvement Canny Edge Detection for the UAV Icing Monitoring of Transmission Line Icing, in Proceedings 16th IEEE Conference Industrial Electronics Applications. ICIEA 2021, Institute of Electrical and Electronics Engineers Inc., pp. 1838–1843. 202110.1109/ICIEA51954.2021.9516053 ↗
7. T. Rashid, H.A. Khawaja, and K. Edvardsen, Review of Marine Icing and Anti-/de-Icing Systems, J. Mar. Eng. Technol., 2016, 15(2), p 79–87.10.1080/20464177.2016.1216734 ↗
8. A.R. Dehghani-Sanij, S.R. Dehghani, G.F. Naterer, and Y.S. Muzychka, Sea Spray Icing Phenomena on Marine Vessels and Offshore Structures: Review and Formulation, Ocean Eng., 2017, 132, p 25–39.10.1016/j.oceaneng.2017.01.016 ↗
9. P. Kim, T.S. Wong, J. Alvarenga, M.J. Kreder, W.E. Adorno-Martinez, and J. Aizenberg, Liquid-Infused Nanostructured Surfaces with Extreme Anti-Ice and Anti-Frost Performance, ACS Nano, 2012, 6(8), p 6569–6577.10.1021/nn302310q ↗
10. J. Lv, Y. Song, L. Jiang, and J. Wang, Bio-Inspired Strategies for Anti-Icing, ACS Nano Am. Chem. Soc., 2014, 8(4), p 3152–3169.10.1021/nn406522n ↗
11. G. Ramakrishnan, G. Dwivedi, S. Sampath, and A. Orlov, Development and Optimization of Thermal Sprayed Ceramic Microfiltration Membranes, J. Membr. Sci., 2015, 489, p 106–111.10.1016/j.memsci.2015.03.094 ↗
12. T.S. Wong, S.H. Kang, S.K.Y. Tang, E.J. Smythe, B.D. Hatton, A. Grinthal, and J. Aizenberg, Bioinspired Self-Repairing Slippery Surfaces with Pressure-Stable Omniphobicity, Nature, 2011, 477(7365), p 443–447.10.1038/nature10447 ↗
13. M.J. Coady, M. Wood, G.Q. Wallace, K.E. Nielsen, A.M. Kietzig, F. Lagugné-Labarthet, and P.J. Ragogna, Icephobic Behavior of UV-Cured Polymer Networks Incorporated into Slippery Lubricant-Infused Porous Surfaces: Improving SLIPS Durability, ACS Appl. Mater. Interfaces, 2018, 10(3), p 2890–2896.10.1021/acsami.7b14433 ↗
14. Y.H. Yeong, C. Wang, K.J. Wynne, and M.C. Gupta, Oil-Infused Superhydrophobic Silicone Material for Low Ice Adhesion with Long-Term Infusion Stability, ACS Appl. Mater. Interfaces, 2016, 8(46), p 32050–32059.10.1021/acsami.6b11184 ↗
15. S.B. Subramanyam, K. Rykaczewski, and K.K. Varanasi, Ice Adhesion on Lubricant-Impregnated Textured Surfaces, Langmuir, 2013, 29(44), p 13414–13418.10.1021/la402456c ↗
16. J. Chen, R. Dou, D. Cui, Q. Zhang, Y. Zhang, F. Xu, X. Zhou, J. Wang, Y. Song, and L. Jiang, Robust Prototypical Anti-Icing Coatings with a Self-Lubricating Liquid Water Layer between Ice and Substrate, ACS Appl. Mater. Interfaces, 2013, 5(10), p 4026–4030.10.1021/am401004t ↗
17. L. Zhu, J. Xue, Y. Wang, Q. Chen, J. Ding, and Q. Wang, Ice-Phobic Coatings Based on Silicon-Oil-Infused Polydimethylsiloxane, ACS Appl. Mater. Interfaces, 2013, 5(10), p 4053–4062.10.1021/am400704z ↗
18. R. Khammas and H. Koivuluoto, Durable Icephobic Slippery Liquid-Infused Porous Surfaces (SLIPS) using Flame- and Cold-Spraying, Sustain. MDPI AG, 2022, 14(14), p 8422–8422.
19. V. Donadei, Icephobicity of Flame-Sprayed Polymer Coatings, Tampere University, 2022, https://trepo.tuni.fi/handle/10024/143284
20. V. Donadei, H. Koivuluoto, E. Sarlin, and P. Vuoristo, Lubricated Icephobic Coatings Prepared by Flame Spraying with Hybrid Feedstock Injection, Surf. Coat. Technol., 2020, 403, p 126396–126396.10.1016/j.surfcoat.2020.126396 ↗
21. V. Donadei, H. Koivuluoto, E. Sarlin, and P. Vuoristo, Icephobic Behaviour and Thermal Stability of Flame-Sprayed Polyethylene Coating: The Effect of Process Parameters, J. Therm. Spray Technol., 2020, 29(1–2), p 241–254.10.1007/s11666-019-00947-0 ↗
22. P.L. Fauchais, J.V.R. Heberlein, and M.I. Boulos, Thermal Spray Fundamentals: From Powder to Part, Springer, Cham, 2014, p 1–156610.1007/978-0-387-68991-3 ↗
23. D. Tejero-Martin, M. Rezvani Rad, A. McDonald, and T. Hussain, Beyond Traditional Coatings: A Review on Thermal-Sprayed Functional and Smart Coatings, J. Therm. Spray Technol., 2019, 28(4), p 598–644.10.1007/s11666-019-00857-1 ↗
24. P. Juuti, J. Haapanen, C. Stenroos, H. Niemelä-Anttonen, J. Harra, H. Koivuluoto, H. Teisala, J. Lahti, M. Tuominen, J. Kuusipalo, P. Vuoristo, and J.M. Mäkelä, Achieving a Slippery, Liquid-Infused Porous Surface with Anti-Icing Properties by Direct Deposition of Flame Synthesized Aerosol Nanoparticles on a Thermally Fragile Substrate, Appl. Phys. Lett., 2017 https://doi.org/10.1063/1.498190510.1063/1.4981905 ↗
25. M. Cao, D. Guo, C. Yu, K. Li, M. Liu, and L. Jiang, Water-Repellent Properties of Superhydrophobic and Lubricant-Infused “Slippery” Surfaces: A Brief Study on the Functions and Applications, ACS Appl. Mater. Interfaces, 2016, 8(6), p 3615–3623.10.1021/acsami.5b07881 ↗
26. N. Wang, D. Xiong, Y. Lu, S. Pan, K. Wang, Y. Deng, and Y. Shi, Design and Fabrication of the Lyophobic Slippery Surface and Its Application in Anti-Icing, J. Phys. Chem. C, 2016, 120(20), p 11054–11059.10.1021/acs.jpcc.6b04778 ↗
27. M. Liu, Y. Hou, J. Li, L. Tie, and Z. Guo, Transparent Slippery Liquid-Infused Nanoparticulate Coatings, Chem. Eng. J., 2018, 337, p 462–470.10.1016/j.cej.2017.12.118 ↗
28. M.I. Jamil, A. Ali, F. Haq, Q. Zhang, X. Zhan, and F. Chen, Icephobic Strategies and Materials with Superwettability: Design Principles and Mechanism, Langmuir, 2018, 34(50), p 15425–15444.10.1021/acs.langmuir.8b03276 ↗
29. P. Chráska, J. Dubsky, K. Neufuss, and J. Pisacka, Alumina-Base Plasma-Sprayed Materials Part I: Phase Stability of Alumina and Alumina-Chromia, J. Therm. Spray Technol., 1997, 6(3), p 320–326.10.1007/s11666-997-0066-9 ↗
30. J.G. Odhiambo, W.G. Li, Y.T. Zhao, and C.L. Li, Porosity and its Significance in Plasma-Sprayed Coatings, Coatings, 2019, 9(7), p 460.10.3390/coatings9070460 ↗
31. S. Rønneberg, C. Laforte, J. He, and Z. Zhang, Comparison of Icephobic Materials through Interlaboratory Studies, Ice Adhesion, John Wiley & Sons, Ltd, 2020, pp. 285–324, https://doi.org/10.1002/9781119640523.ch1010.1002/9781119640523.ch10 ↗
32. L.B. Boinovich and A.M. Emelyanenko, Recent Progress in Understanding the Anti-Icing Behavior of Materials, Adv. Colloid Interface Sci., 2024, 323, p 103057.10.1016/j.cis.2023.103057 ↗
33. S. Rønneberg, J. He, and Z. Zhang, The Need for Standards in Low Ice Adhesion Surface Research: A Critical Review, J. Adhes. Sci. Technol., 2020, 34(3), p 319–347.10.1080/01694243.2019.1679523 ↗
34. Z. He, Y. Zhuo, Z. Zhang, and J. He, Design of Icephobic Surfaces by Lowering Ice Adhesion Strength: A Mini Review, Coat, 2021, 11(11), p 1343–1343.10.3390/coatings11111343 ↗
35. S.A. Kulinich, D. Masson, X.-W. Du, and A.M. Emelyanenko, Testing the Durability of Anti-Icing Coatings, Ice Adhesion, 2020, pp. 495–519, https://doi.org/10.1002/9781119640523.ch1610.1002/9781119640523.ch16 ↗
36. K. Golovin, S.P.R. Kobaku, D.H. Lee, E.T. DiLoreto, J.M. Mabry, and A. Tuteja, Designing Durable Icephobic Surfaces, Sci. Adv., 2016, 2(3), p e1501496.10.1126/sciadv.1501496 ↗
37. V. Hejazi, K. Sobolev, and M. Nosonovsky, From Superhydrophobicity to Icephobicity: Forces and Interaction Analysis, Sci. Rep., 2013, 3(1), p 1–6.10.1038/srep02194 ↗
38. M.C. Gupta and A. Mulroney, Ice Adhesion and Anti-Icing Using Microtextured Surfaces, Ice Adhesion, 2020, pp. 389–415, https://doi.org/10.1002/9781119640523.ch13.10.1002/9781119640523.ch13 ↗
39. H. Koivuluoto, E. Hartikainen, and H. Niemelä-Anttonen, Thermally Sprayed Coatings: Novel Surface Engineering Strategy towards Icephobic Solutions, Materials, 2020, 13(6), p 1434. https://doi.org/10.3390/ma1306143410.3390/ma13061434 ↗
40. H. Niemelä-Anttonen, H. Koivuluoto, M. Tuominen, H. Teisala, P. Juuti, J. Haapanen, J. Harra, C. Stenroos, J. Lahti, J. Kuusipalo, J.M. Mäkelä, and P. Vuoristo, Icephobicity of Slippery Liquid Infused Porous Surfaces under Multiple Freeze-Thaw and Ice Accretion-Detachment Cycles, Adv. Mater. Interfaces, 2018 https://doi.org/10.1002/admi.20180082810.1002/admi.201800828 ↗
41. G. Liu, Y. Yuan, R. Liao, L. Wang, and X. Gao, Fabrication of a Porous Slippery Icephobic Surface and Effect of Lubricant Viscosity on Anti-Icing Properties and Durability, Coatings, 2020, 10(9), p 896.10.3390/coatings10090896 ↗
42. V. Donadei, H. Koivuluoto, E. Sarlin, H. Niemelä-Anttonen, T. Varis, and P. Vuoristo, The Effect of Mechanical and Thermal Stresses on the Performance of Lubricated Icephobic Coatings during Cyclic Icing/Deicing Tests, Prog. Org. Coat., 2022, 163, p 106614.10.1016/j.porgcoat.2021.106614 ↗
43. G. McHale, B.V. Orme, G.G. Wells, and R. Ledesma-Aguilar, Apparent Contact Angles on Lubricant-Impregnated Surfaces/SLIPS: From Superhydrophobicity to Electrowetting, Langmuir, 2019, 35(11), p 4197–4204.10.1021/acs.langmuir.8b04136 ↗