journal article·2024-10Open access

Optimizing Cold Spray Parameters for High Entropy Alloy Coatings Using Taguchi and Box–Behnken Design Approaches for Mechanically Alloyed Powder

Deepak Sharma, Dibakor Boruah, Ahamed Ameen, Ali Alperen Bakir, Shiladitya Paul

Abstract

Abstract The present study focused on optimizing the cold spray (CS) process parameters for depositing Fe20Cr20Mn20Ni20Co20 (Cantor alloy) coatings using mechanically alloyed (MA) powder. A two-step design of experiments approach was employed, beginning with the initial screening of input variables using the L8 Taguchi method, followed by the refinement of process parameters through the Box–Behnken design of experiments. Key performance indicators included deposition efficiency (DE), coating thickness per pass, and microstructural parameters including porosity, cracks, and interfacial defects/delamination. The study identified process gas temperature as the primary factor influencing both DE and thickness per pass. Higher gas temperature and pressure, combined with increased scanning speed, resulted in higher DE. The DE of the MA Cantor alloy powder peaked at around 14-15%, with a deposit density greater than 99% achieved at the highest process gas temperature and pressure (1000 °C and 60 bar, respectively). The average hardness of the optimal CS coating deposited using MA powder was found to be 679 ± 17 HV0.1, which is approximately 90% greater than the average hardness reported for CS coatings deposited using atomized powder.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: High-Temperature Coating Behaviors · High Entropy Alloys Studies · Advanced materials and composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (49)

Show source-provided references
1. D.B. Miracle and O.N. Senkov, A Critical Review of High Entropy Alloys and Related Concepts, Acta Mater., 2017, 122, p 448-511. https://doi.org/10.1016/j.actamat.2016.08.08110.1016/j.actamat.2016.08.081 ↗
2. B. Cantor, Multicomponent High-Entropy Cantor Alloys, Prog. Mater. Sci., 2021, 120, p 100754. https://doi.org/10.1016/j.pmatsci.2020.10075410.1016/j.pmatsci.2020.100754 ↗
3. T.K. Chen, T.T. Shun, J.W. Yeh, and M.S. Wong, Nanostructured Nitride Films of Multi-element High-Entropy Alloys by Reactive DC Sputtering, Surf. Coat. Technol., 2004, 188–189, p 193-200. https://doi.org/10.1016/j.surfcoat.2004.08.02310.1016/j.surfcoat.2004.08.023 ↗
4. B. Cantor, I.T.H. Chang, P. Knight, and A.J.B. Vincent, Microstructural Development in Equiatomic Multicomponent Alloys, Mater. Sci. Eng. A, 2004, 375–377, p 213-218. https://doi.org/10.1016/j.msea.2003.10.25710.1016/j.msea.2003.10.257 ↗
5. W. Ji and M.S. Wu, Nanoscale Insights into the Damage Tolerance of Cantor Alloys at Cryogenic Temperatures, Int. J. Mech. Sci., 2022, 226, p 107406. https://doi.org/10.1016/j.ijmecsci.2022.10740610.1016/j.ijmecsci.2022.107406 ↗
6. Z. Han, W. Ren, J. Yang, A. Tian, Y. Du, G. Liu, R. Wei, G. Zhang, and Y. Chen, The Corrosion Behavior of Ultra-Fine Grained CoNiFeCrMn High-Entropy Alloys, J. Alloys Compd., 2020, 816, p 152583. https://doi.org/10.1016/j.jallcom.2019.15258310.1016/j.jallcom.2019.152583 ↗
7. Z. Zeng, M. Xiang, D. Zhang, J. Shi, W. Wang, X. Tang, W. Tang, Y. Wang, X. Ma, Z. Chen, W. Ma, and K. Morita, Mechanical Properties of Cantor Alloys Driven by Additional Elements: A Review, J. Mater. Res. Technol., 2021, 15, p 1920-1934. https://doi.org/10.1016/j.jmrt.2021.09.01910.1016/j.jmrt.2021.09.019 ↗
8. E.P. George, W.A. Curtin, and C.C. Tasan, High Entropy Alloys: A Focused Review of Mechanical Properties and Deformation Mechanisms, Acta Mater., 2020, 188, p 435-474. https://doi.org/10.1016/j.actamat.2019.12.01510.1016/j.actamat.2019.12.015 ↗
9. A. Srikanth, M. Thalib, G. Basha, and B. Venkateshwarlu, ScienceDirect A Brief Review on Cold Spray Coating Process, Mater. Today Proc., 2020, 22, p 1390-1397. https://doi.org/10.1016/j.matpr.2020.01.48210.1016/j.matpr.2020.01.482 ↗
10. H. Assadi, H. Kreye, F. Gärtner, and T. Klassen, Cold Spraying—A Materials Perspective, Acta Mater., 2016, 116, p 382-407. https://doi.org/10.1016/j.actamat.2016.06.03410.1016/j.actamat.2016.06.034 ↗
11. C.A. Widener, O.C. Ozdemir, and M. Carter, Structural Repair Using Cold Spray Technology for Enhanced Sustainability of High Value Assets, Procedia Manuf., 2018, 21, p 361-368. https://doi.org/10.1016/j.promfg.2018.02.13210.1016/j.promfg.2018.02.132 ↗
12. T. Liao, A. Biesiekierski, C.C. Berndt, P.C. King, E.P. Ivanova, H. Thissen, and P. Kingshott, Progress in Surface Science Multifunctional Cold Spray Coatings for Biological and Biomedical Applications: A Review, Prog. Surf. Sci., 2022, 97, p 100654. https://doi.org/10.1016/j.progsurf.2022.10065410.1016/j.progsurf.2022.100654 ↗
13. M. Ashokkumar, D. Thirumalaikumarasamy, T. Sonar, S. Deepak, P. Vignesh, and M. Anbarasu, An Overview of Cold Spray Coating in Additive Manufacturing, Component Repairing and Other Engineering Applications, J. Mech. Behav. Mater., 2022, 31(1), p 514-534.10.1515/jmbm-2022-0056 ↗
14. R. Nikbakht, M. Saadati, T. Kim, M. Jahazi, H. Seop, and B. Jodoin, Cold Spray Deposition Characteristic and Bonding of CrMnCoFeNi High Entropy Alloy, Surf. Coat. Technol., 2021, 425, p 127748. https://doi.org/10.1016/j.surfcoat.2021.12774810.1016/j.surfcoat.2021.127748 ↗
15. J.E. Ahn, Y.K. Kim, S.H. Yoon, and K.A. Lee, Tuning the Microstructure and Mechanical Properties of Cold Sprayed Equiatomic CoCrFeMnNi High-Entropy Alloy Coating Layer, Met. Mater. Int., 2021, 27, p 2406-2415. https://doi.org/10.1007/s12540-020-00886-410.1007/s12540-020-00886-4 ↗
16. R. Nikbakht, C.V. Cojocaru, and M. Aghasibeig, Cold Spray and Laser-Assisted Cold Spray of CrMnCoFeNi High Entropy Alloy Using Nitrogen as the Propelling Gas, J. Therm. Spray Technol., 2022, 31, p 1129-1142. https://doi.org/10.1007/s11666-022-01361-910.1007/s11666-022-01361-9 ↗
17. J. Mahaffey, A. Vackel, S. Whetten, M. Melia, and A.B. Kustas, Structure Evolution and Corrosion Performance of CoCrFeMnNi High Entropy Alloy Coatings Produced via Plasma Spray and Cold Spray, J. Therm. Spray Technol., 2022, 31, p 1143-1154. https://doi.org/10.1007/s11666-022-01373-510.1007/s11666-022-01373-5 ↗
18. Y. Xu, W. Li, L. Qu, X. Yang, B. Song, and R. Lupoi, Solid-State Cold Spraying of FeCoCrNiMn High-Entropy Alloy: An Insight into Microstructure Evolution and Oxidation Behavior at 700–900 °C, J. Mater. Sci. Technol., 2021, 68, p 172-183. https://doi.org/10.1016/j.jmst.2020.06.04110.1016/j.jmst.2020.06.041 ↗
19. D. Wu, Y. Xu, W. Li, N. Fan, Y. Yang, and S. Yin, Significant Improvement of Mechanical Properties of Cold-Spray-Additive Manufactured FeCoNiCrMn High-Entropy Alloy via Post-annealing, Mater Charact, 2023, 206, p 113350. https://doi.org/10.1016/j.matchar.2023.11335010.1016/j.matchar.2023.113350 ↗
20. P. Yu, N. Fan, Y. Zhang, Z. Wang, and W. Li, Microstructure Evolution and Composition Redistribution of FeCoNiCrMn High Entropy Alloy under Extreme Plastic Deformation, Mater. Res. Lett., 2022, 10, p 124-132. https://doi.org/10.1080/21663831.2021.202367810.1080/21663831.2021.2023678 ↗
21. C.J. Akisin, B. Dovgyy, C.J. Bennett, F. Venturi, and T. Hussain, Microstructural Study of Cold-Sprayed CoCrFeNiMn High Entropy Alloy, J. Therm. Spray Technol., 2023, 32, p 2539-2562. https://doi.org/10.1007/s11666-023-01646-710.1007/s11666-023-01646-7 ↗
22. S. Yin, W. Li, B. Song, X. Yan, M. Kuang, Y. Xu, and K. Wen, Deposition of FeCoNiCrMn High Entropy Alloy (HEA) Coating via Cold Spraying, J. Mater. Sci. Technol., 2019, 35, p 1003-1007. https://doi.org/10.1016/j.jmst.2018.12.01510.1016/j.jmst.2018.12.015 ↗
23. S. Feng, S. Guan, W.A. Story, J. Ren, S. Zhang, A. Te, M.A. Gleason, J. Heelan, C. Walde, A. Birt, K.L. Tsaknopoulos, D.L. Cote, W. Kapalczynski, A.T. Naardi, V.K. Champagne, M.J. Siopis, and W. Chen, Cold Spray Additive Manufacturing of CoCrFeNiMn High-Entropy Alloy: Process Development, Microstructure, and Mechanical Properties, J. Therm. Spray Technol., 2022, 31, p 1222-1231. https://doi.org/10.1007/s11666-022-01374-410.1007/s11666-022-01374-4 ↗
24. C.J. Akisin, C.J. Bennett, F. Venturi, and H. Assadi, Numerical and Experimental Analysis of the Deformation Behavior of CoCrFeNiMn High Entropy Alloy Particles onto Various Substrates during Cold Spraying, J. Therm. Spray Technol., 2022, 31, p 1085-1111. https://doi.org/10.1007/s11666-022-01377-110.1007/s11666-022-01377-1 ↗
25. P. Cavaliere, A. Perrone, A. Silvello, A. Laska, G. Blasi, I.G. Cano, B. Sadeghi, and S. Nagy, Cyclic behavior of FeCoCrNiMn high entropy alloy coatings produced through cold spray, J. Alloys Compd., 2023, 931, p 167550. https://doi.org/10.1016/j.jallcom.2022.16755010.1016/j.jallcom.2022.167550 ↗
26. P. Cavaliere, A. Perrone, A. Silvello, A. Laska, G. Blasi, and I.G. Cano, Fatigue Bending of V-Notched Cold-Sprayed FeCoCrNiMn Coatings, Metals (Basel), 2022, 12, p 1-21. https://doi.org/10.3390/met1205078010.3390/met12050780 ↗
27. C. Suryanarayana, Mechanical Alloying: A Critical Review, Mater. Res. Lett., 2022, 10, p 619-647. https://doi.org/10.1080/21663831.2022.207524310.1080/21663831.2022.2075243 ↗
28. B. Durakovic, Design of Experiments Application, Concepts Examples: State of the Art, Period. Eng. Nat. Sci., 2021 https://doi.org/10.21533/pen.v5i3.14510.21533/pen.v5i3.145 ↗
29. J.K. Telford, A Brief Introduction to Design of Experiments, Johns Hopkins APL Tech. Dig., 2007, 27, p 224-232.
30. M. Almeida, R. Erthal, E. Padua, L. Silveira, L. Am, Talanta Response surface methodology ( RSM ) as a tool for optimization in analytical chemistry, 76 (2008) 965-977. https://doi.org/10.1016/j.talanta.2008.05.019.10.1016/j.talanta.2008.05.019 ↗
31. K.N. Ballantyne, R.A. Van Oorschot, and R.J. Mitchell, Reduce Optimisation Time and Effort: Taguchi Experimental Design Methods, Forensic Sci. Int. Genet. Suppl. Ser., 2008, 1, p 7-8. https://doi.org/10.1016/j.fsigss.2007.10.05010.1016/j.fsigss.2007.10.050 ↗
32. Y. Ma, H. Hu, D. Northwood, and X. Nie, Optimization of the Electrolytic Plasma Oxidation Processes for Corrosion Protection of Magnesium Alloy AM50 Using the Taguchi Method, J. Mater. Process. Technol., 2007, 182, p 58-64. https://doi.org/10.1016/j.jmatprotec.2006.07.00710.1016/j.jmatprotec.2006.07.007 ↗
33. S. Sarkar, R.K. Baranwal, and S. Banerjee, Parametric Optimization of Process Parameters on the Response of Microhardness of Electroless Ni-P Coating, J. Mol. Eng. Mater., 2019, 6, p 1-8. https://doi.org/10.1142/S225123731850003X10.1142/S225123731850003X ↗
34. S. Sarkar, A. Mukherjee, R.K. Baranwal, J. De, C. Biswas, and G. Majumdar, Prediction and Parametric Optimization of Surface Roughness of Electroless Ni-Co-P Coating Using Box-Behnken Design, J. Mech. Behav. Mater., 2019, 28, p 153-161.10.1515/jmbm-2019-0017 ↗
35. S.S. Sabari, Prediction and Optimization of Process Variables to Maximize the Young’s Modulus of Plasma Sprayed Alumina Coatings on AZ31B Magnesium Alloy, J. Magnes. Alloy., 2017, 5, p 133-145. https://doi.org/10.1016/j.jma.2017.02.00210.1016/j.jma.2017.02.002 ↗
36. G. Wang, L. Huang, Z. Liu, Z. Qin, W. He, and F. Liu, Process Optimization and Mechanical Properties of Oxide Dispersion Strengthened Nickel-Based Superalloy by Selective Laser Melting, Mater. Des., 2020, 188, 108418. https://doi.org/10.1016/j.matdes.2019.10841810.1016/j.matdes.2019.108418 ↗
37. A.R. Alao and M. Konneh, Application of Taguchi and Box-Behnken Designs for Surface Roughness in Precision Grinding of Silicon, Int. J. Precis. Technol., 2011, 2, p 21-38.10.1504/IJPTECH.2011.038107 ↗
38. A.R. Reghuraj, K. Saju, and A. Ritwik, Taguchi Method and Box-Behnken Design Approach for Process Parameter Optimization of Magnetite (Fe3O4) Coating Developed on Stainless Steel 410 Grade by Hot Alkaline Treatment, Proc. Inst. Mech. Eng. Part E J. Process Mech. Eng., 2023, 237(4), p 1583-1594. https://doi.org/10.1177/0954408922111924410.1177/09544089221119244 ↗
39. D. Wu, Y. Xu, W. Li, Y. Yang, K. Liu, W. Wan, and Z. Qi, Process Optimisation of Cold Spray Additive Manufacturing of FeCoNiCrMn High-Entropy Alloy, Sci. Technol. Weld. Join., 2023 https://doi.org/10.1080/13621718.2023.219026410.1080/13621718.2023.2190264 ↗
40. A. Silvello, P. Cavaliere, S. Yin, R. Lupoi, I. Garcia Cano, and S. Dosta, Microstructural, Mechanical and Wear Behavior of HVOF and Cold-Sprayed High-Entropy Alloys (HEAs) Coatings, J. Therm. Spray Technol., 2022, 31, p 1184-1206. https://doi.org/10.1007/s11666-021-01293-w10.1007/s11666-021-01293-w ↗
41. F. Otto, A. Dlouhý, K.G. Pradeep, M. Kuběnová, D. Raabe, G. Eggeler, and E.P. George, Decomposition of the Single-Phase High-Entropy Alloy CrMnFeCoNi After Prolonged Anneals at Intermediate Temperatures, Acta Mater., 2016, 112, p 40-52. https://doi.org/10.1016/j.actamat.2016.04.00510.1016/j.actamat.2016.04.005 ↗
42. D. Boruah, B. Ahmad, T.L. Lee, S. Kabra, A.K. Syed, P. McNutt, M. Doré, and X. Zhang, Evaluation of Residual Stresses Induced by Cold Spraying of Ti-6Al-4V on Ti-6Al-4V Substrates, Surf. Coat. Technol., 2019, 374, p 591-602. https://doi.org/10.1016/j.surfcoat.2019.06.02810.1016/j.surfcoat.2019.06.028 ↗
43. D. Boruah, X. Zhang, and M. Doré, Theoretical Prediction of Residual Stresses Induced by Cold Spray with Experimental Validation, Multidiscip. Model. Mater. Struct., 2019, 15, p 599-616. https://doi.org/10.1108/MMMS-08-2018-015010.1108/MMMS-08-2018-0150 ↗
44. V.K. Champagne Ed., The Cold Spray Materials Deposition Process: Fundamentals and Applications, Woodhead Publishing, Cambridge, 2007
45. M. Grujicic, C.L. Zhao, W.S. DeRosset, and D. Helfritch, Adiabatic Shear Instability Based Mechanism for Particles/Substrate Bonding in the Cold-Gas Dynamic-Spray Process, Mater. Des., 2004, 25, p 681-688. https://doi.org/10.1016/j.matdes.2004.03.00810.1016/j.matdes.2004.03.008 ↗
46. D. Sharma, D. Boruah, A.A. Bakir, A. Ameen, and S. Paul, Machine Learning-Based Predictions of Porosity during Cold Spray Deposition of High Entropy Alloy Coatings, Coatings, 2024, 14, p 404. https://doi.org/10.3390/coatings1404040410.3390/coatings14040404 ↗
47. C. Suryanarayana, Mechanical Alloying and Milling, Prog. Mater. Sci., 2001, 46, p 1-184. https://doi.org/10.1016/S0079-6425(99)00010-910.1016/S0079-6425(99)00010-9 ↗
48. D. Sharma, P.K. Ghosh, R. Anant, and S. Kumar, Surface Modification of Microalloyed Steel by Silicon Carbide Reinforcement Using Tungsten Inert Gas Arcing, Mater. Res. Express, 2019, 6, p 36530. https://doi.org/10.1088/2053-1591/aaf7d810.1088/2053-1591/aaf7d8 ↗
49. D. Sharma, M. Kamran, N.K. Paraye, and R. Anant, Insights into the Wear Behaviour of Electron Beam Melted Ti–6Al–4V Alloy in the As-Built and the Heat-Treated Conditions, J. Manuf. Process., 2021, 71, p 669-678. https://doi.org/10.1016/j.jmapro.2021.09.06010.1016/j.jmapro.2021.09.060 ↗