Reusing 316L Stainless Steel Feedstock Powder for Cold Spray Deposition
Source abstract
Abstract
Abstract Cold spray (CS) is a solid-state deposition of coatings, or an additive manufacturing (CSAM) process employed to make parts maintaining the feedstock powders properties in the deposited material. One of the cons for industrial use of CS or CSAM is their higher costs compared to the traditional coating or manufacturing processes. Reducing the feedstock powder consumption by maximizing the deposition efficiency has been the focus of many works. However, depending on the part geometry (e.g., a plate with holes), and CSAM strategy with low deposition efficiency, a considerable mass of powder can pass through the substrate, failing to bond, and becoming a process waste. This work evaluates CS 316L stainless steel coatings, recovering the unbonded particles and reusing them in a later deposition, thus making coatings with reused powders. The original and recovered powders were characterized in terms of particle shape and size distribution, phase composition, microhardness, and other properties to evaluate the evolution of the particles' properties due to the recovery process. Besides the powders, the CS coatings obtained with original and recovered powders were evaluated through cross-section image analysis, where porosity, deposition efficiency, and microhardness were observed. The results indicate that the powders' physical properties undergo variations over multiple deposition cycles without significantly affecting the quality of the CS coatings, with porosity below 1.5% and microhardness around 350 HV0.3 in most cases. Recovering and reusing powder for CS promotes environmental sustainability and generates significant economic benefits. This study contributes to making CS more economically viable from a life cycle cost assessment perspective. Graphical abstract
Source: crossref · Quality: baseline
Research context
OpenAlex topics: High-Temperature Coating Behaviors · Fluid Dynamics and Heat Transfer · Particle Dynamics in Fluid Flows
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (32)
Show source-provided references
1. M.R. Rokni, S.R. Nutt, C.A. Widener, V.K. Champagne and R.H. Hrabe, Review of Relationship Between Particle Deformation, Coating Microstructure, and Properties in High-Pressure Cold Spray, J. Therm. Spray Technol., 2017, 26, p 1308-1355. https://doi.org/10.1007/s11666-017-0575-010.1007/s11666-017-0575-0 ↗
2. H. Assadi, F. Gärtner, T. Stoltenhoff and H. Kreye, Bonding Mechanism in Cold Gas Spraying, Acta Mater., 2003, 51, p 4379-4394. https://doi.org/10.1016/S1359-6454(03)00274-X10.1016/S1359-6454(03)00274-X ↗
3. R.F. Vaz, A. Garfias, V. Albaladejo, J. Sanchez and I.G. Cano, A Review of Advances in Cold Spray Additive Manufacturing, Coatings, 2023 https://doi.org/10.3390/coatings1302026710.3390/coatings13020267 ↗
4. R.F. Vaz, V. Albaladejo-Fuentes, J. Sanchez, U. Ocaña, Z.G.Z.G. Corral, H. Canales and I.G. Cano, Metal Knitting: A New Strategy for Cold Gas Spray, Materials (Basel)., 2022, 15, p 1-17. https://doi.org/10.3390/ma1519678510.3390/ma15196785 ↗
5. L.H. Guilherme, A.V. Benedetti, C.S. Fugivara, R. Magnabosco and M.F. Oliveira, Effect of MAG Welding Transfer Mode on Sigma Phase Precipitation and Corrosion Performance of 316L Stainless Steel Multi-pass Welds, J. Mater. Res. Technol., 2020, 9, p 10537-10549. https://doi.org/10.1016/j.jmrt.2020.07.03910.1016/j.jmrt.2020.07.039 ↗
6. E.R.I. Mahmoud, S.Z. Khan and M. Ejaz, Laser Surface Cladding of Mild Steel with 316L Stainless Steel for Anti-corrosion Applications, Mater. Today Proc., 2021, 39, p 1029-1033. https://doi.org/10.1016/j.matpr.2020.04.76310.1016/j.matpr.2020.04.763 ↗
7. M. Hassani-gangaraj, D. Veysset, V.K. Champagne, K.A. Nelson and C.A. Schuh, Adiabatic Shear Instability is Not Necessary for Adhesion in Cold Spray, Acta Mater., 2018, 158, p 430-439. https://doi.org/10.1016/j.actamat.2018.07.06510.1016/j.actamat.2018.07.065 ↗
8. A. Haider and O. Levenspiel, Drag Coefficient and Terminal Velocity of Spherical and Nonspherical Particles, Powder Technol., 1989, 58, p 63-70. https://doi.org/10.1016/0032-5910(89)80008-710.1016/0032-5910(89)80008-7 ↗
9. R.F. Vaz, A. Silvello, J. Sanchez, V. Albaladejo and I. García-Cano, The Influence of the Powder Characteristics on 316l Stainless Steel Coatings Sprayed by Cold Gas Spray, Coatings, 2021, 11, p 1-18. https://doi.org/10.3390/coatings1102016810.3390/coatings11020168 ↗
10. V.S. Bhattiprolu, K.W. Johnson, O.C. Ozdemir and G.A. Crawford, Influence of Feedstock Powder and Cold Spray Processing Parameters on Microstructure and Mechanical Properties of Ti-6Al-4V Cold Spray Depositions, Surf. Coatings Technol., 2018, 335, p 1-12. https://doi.org/10.1016/j.surfcoat.2017.12.01410.1016/j.surfcoat.2017.12.014 ↗
11. D. MacDonald, R. Fernández, F. Delloro and B. Jodoin, Cold Spraying of Armstrong Process Titanium Powder for Additive Manufacturing, J. Therm. Spray Technol., 2017, 26, p 598-609. https://doi.org/10.1007/s11666-016-0489-210.1007/s11666-016-0489-2 ↗
12. M. Jeandin, G. Rolland, L.L. Descurninges and M.H. Berger, Which Powders for Cold Spray?, Surf. Eng., 2014, 30, p 291-298. https://doi.org/10.1179/1743294414Y.000000025310.1179/1743294414Y.0000000253 ↗
13. C.-J. Li, H.-T. Wang, Q. Zhang, G.-J. Yang, W.-Y. Li and H.L. Liao, Influence of Spray Materials and Their Surface Oxidation on the Critical Velocity in Cold Spraying, J. Therm. Spray Technol., 2010, 19, p 95-101. https://doi.org/10.1007/s11666-009-9427-x10.1007/s11666-009-9427-x ↗
14. V. Viswanathan, N.K. Katiyar, G. Goel, A. Matthews and S. Goel, Role of Thermal Spray in Combating Climate Change, Emergent Mater., 2021, 4, p 1515-1529. https://doi.org/10.1007/s42247-021-00307-110.1007/s42247-021-00307-1 ↗
15. C. Lu, R. Zhang, M. Xiao, X. Wei, Y. Yin, Y. Qu, H. Li, P. Liu, X. Qiu and T. Guo, A Comprehensive Characterization of Virgin and Recycled 316L Powders During Laser Powder Bed Fusion, J. Mater. Res. Technol., 2022, 18, p 2292-2309. https://doi.org/10.1016/j.jmrt.2022.03.12510.1016/j.jmrt.2022.03.125 ↗
16. K.L. Terrassa, J.C. Haley, B.E. MacDonald and J.M. Schoenung, Reuse of Powder Feedstock for Directed Energy Deposition, Powder Technol., 2018, 338, p 819-829. https://doi.org/10.1016/j.powtec.2018.07.06510.1016/j.powtec.2018.07.065 ↗
17. A. Jenike, Storage and flow of solids, 1964 https://doi.org/10.2172/524025710.2172/5240257 ↗
18. J. Zegzulka, D. Gelnar, L. Jezerska, R. Prokes and J. Rozbroj, Characterization and Flowability Methods for Metal Powders, Sci. Rep., 2020, 10, p 21004. https://doi.org/10.1038/s41598-020-77974-310.1038/s41598-020-77974-3 ↗
19. M. Ben Ohoud, F. Obrecht, L. Gatineua, P. Levitz and H. Van Damme, Surface Area, Mass Fractal Dimension, and Apparent Density of Powders, J. Colloid Interface Sci., 1988 https://doi.org/10.1016/0021-9797(88)90336-010.1016/0021-9797(88)90336-0 ↗
20. R.F. Vaz, A. Garfias, V. Albaladejo, J. Sanchez and I.G. Cano, How Increasing Cold Spray Coatings Thickness Affects Their Residual Stress and Properties, Surf. Coatings Technol., 2024, 485, 130867. https://doi.org/10.1016/j.surfcoat.2024.13086710.1016/j.surfcoat.2024.130867 ↗
21. N. Solomon and I. Solomon, Deformation Induced Martensite in AISI 316 Stainless Steel, Rev. Metal., 2010, 46, p 121-128. https://doi.org/10.3989/revmetalm.092010.3989/revmetalm.0920 ↗
22. K. Spencer and M.-X. Zhang, Optimisation of Stainless Steel Cold Spray Coatings Using Mixed Particle Size Distributions, Surf. Coat. Technol., 2011, 205, p 5135-5140. https://doi.org/10.1016/j.surfcoat.2011.05.02010.1016/j.surfcoat.2011.05.020 ↗
23. A.Y. Chen, H.H. Ruan, J. Wang, H.L. Chan, Q. Wang, Q. Li and J. Lu, The Influence of Strain Rate on the Microstructure Transition of 304 Stainless Steel, Acta Mater., 2011, 59, p 3697-3709. https://doi.org/10.1016/j.actamat.2011.03.00510.1016/j.actamat.2011.03.005 ↗
24. H.-S. Kim and S.-H. Park, Significant Dislocation Strengthening of Stainless Steel 316L Via Co-directed Energy Deposition of Silica, Mater. Sci. Eng. A, 2024, 891, 145948. https://doi.org/10.1016/j.msea.2023.14594810.1016/j.msea.2023.145948 ↗
25. R.F. Vaz, L.L. Silveira, J.R. Cruz and A.G.M. Pukasiewicz, Cavitation Resistance of FeMnCrSi Coatings Processed by Different Thermal Spray Processes, Hybrid Adv., 2024, 5, 100125. https://doi.org/10.1016/j.hybadv.2023.10012510.1016/j.hybadv.2023.100125 ↗
26. Y. Zou, W. Qin, E. Irissou, J. Legoux, S. Yue and J.A. Szpunar, Dynamic Recrystallization in the Particle/Particle Interfacial Region of Cold-Sprayed Nickel Coating: Electron Backscatter Diffraction Characterization, Scr. Mater., 2009, 61, p 899-902. https://doi.org/10.1016/j.scriptamat.2009.07.02010.1016/j.scriptamat.2009.07.020 ↗
27. H. Yeom, T. Dabney, N. Pocquette, K. Ross, F.E. Pfefferkorn and K. Sridharan, Cold Spray Deposition of 304L Stainless Steel to Mitigate Chloride-Induced Stress Corrosion Cracking in Canisters for Used Nuclear Fuel Storage, J. Nucl. Mater., 2020, 538, p 152254. https://doi.org/10.1016/j.jnucmat.2020.15225410.1016/j.jnucmat.2020.152254 ↗
28. A. Vargas-Uscategui, P.C. King, S. Yang, C. Chu and J. Li, Toolpath Planning for Cold Spray Additively Manufactured Titanium Walls and Corners: Effect on Geometry and Porosity, J. Mater. Process. Technol., 2021, 298, 117272. https://doi.org/10.1016/j.jmatprotec.2021.11727210.1016/j.jmatprotec.2021.117272 ↗
29. A. Vargas-Uscategui, P.C. King, M.J. Styles, M. Saleh, V. Luzin and K. Thorogood, Residual Stresses in Cold Spray Additively Manufactured Hollow Titanium Cylinders, J. Therm. Spray Technol., 2020, 29, p 1508-1524. https://doi.org/10.1007/s11666-020-01028-310.1007/s11666-020-01028-3 ↗
30. M. Boisvert, D. Christopherson, P. Beaulieu and G. L’Espérance, Treatment of Ferrous Melts for the Improvement of the Sphericity of Water Atomized Powders, Mater. Des., 2017, 116, p 644-655. https://doi.org/10.1016/j.matdes.2016.12.05910.1016/j.matdes.2016.12.059 ↗
31. A.G.M. Pukasiewicz, W.R. de Oliveira, R.F. Váz, G.B. de Souza, F.C. Serbena, S. Dosta and I.G. Cano, Influence of the Deposition Parameters on the Tribological Behavior of Cold Gas Sprayed FeMnCrSi Alloy Coatings, Surf. Coat. Technol., 2021, 428, p 127888. https://doi.org/10.1016/j.surfcoat.2021.12788810.1016/j.surfcoat.2021.127888 ↗
32. R. Nikbakht, C.V. Cojocaru, M. Aghasibeig, É. Irissou, T.-S. Kim, H.S. Kim and B. Jodoin, Cold Spray and Laser-Assisted Cold Spray of CrMnCoFeNi High Entropy Alloy Using Nitrogen as the Propelling Gas, J. Therm. Spray Technol., 2022, 31, p 1129-1142. https://doi.org/10.1007/s11666-022-01361-910.1007/s11666-022-01361-9 ↗