Cold Spray Additive Manufacturing of SmCo-Al Permanent Magnets
Source abstract
Abstract
Abstract A key factor to ensure a sustainable future for the air transport industry is electrification. Exploring new designs for permanent magnet electric motors could increase their potential. Unfortunately, complex shaped magnets cannot be produced easily using current fabrication methods. Cold spray additive manufacturing could eventually help to alleviate this problem by allowing the fabrication of magnets with complex geometries consolidated on electric motor parts. Furthermore, another aspect to increase the electric motors’ efficiency is the possibility to operate at higher RPM and with higher electrical currents, consequently generating more heat. Currently, most magnets are prepared with NdFeB, which is less tolerant to high-temperature exposure. This work reports on the cold spray additive manufacturing of samarium-cobalt (SmCo), a material of growing interest since it preserves most of its magnetic properties up to 350 °C. The permanent magnets were fabricated using a SmCo-Al composite powder mix in a standardized simple geometry to evaluate the impact of the fabrication parameters. The impact of the powder mix composition and the gas temperature on the magnetic properties is investigated. The results demonstrate that the use of cold spray would be effective for fabricating SmCo composite permanent magnets directly on the electric motor parts.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Magnetic Properties of Alloys · Metallic Glasses and Amorphous Alloys · Hydrogen Storage and Materials
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (26)
Show source-provided references
1. Deloitte, Europe’s Future Aviation Landscape: The Potential of Zero-Carbon and Zero-Emissions Aircraft on Intra-European Routes by 2040 (2021)
2. World Economic Forum & McKinsey, Clean Skies for Tomorrow: Sustainable Aviation Fuels as a Pathway to Net-Zero Aviation (2020)
3. National Academies of Science Engineering and Medecine, Commercial Aircraft Propulsion and Energy Systems Research: Reducing Global Carbon Emissions, National Academies Press (2016)
4. H. Kronmuller and S. Parkin, Handbook of Magnetism and Advanced Magnetic Materials, Wiley, Hoboken, 2007.10.1002/9780470022184 ↗
5. J. Huang, K. Yung, and D. Ang, Magnetic Properties of SmCo5 Alloy Fabricated by Laser Sintering, J. Mater. Sci. Mater. Electron., 2019, 30(12), p 11282-11290.10.1007/s10854-019-01475-x ↗
6. D. Goll, F. Trauter, P. Braun, J. Lakart, R. Loeffler, U. Golla-Schindler and G. Schneider, Additive Manufacturing of Permanent Magnets Based on (CoCuFeZr)17Sm2, Phys. Status Solidi, 2021, 15(10), p 2100294.
7. R. Gopalan, T. Sastry, A. Singh, and V. Chandrasekaran, X-ray Difraction and Microstructural Studies in 2:17 Type Sm-Co Magnetic Alloy Containing Fe, Cu and Zr, J. Mater. Res., 1998, 14, p 2430-2435.10.1557/JMR.1999.0326 ↗
8. A. Popov, O. Golovnia, A. Protasov, V. Gaviko, D. Kolodkin, and R. Gopalan, Coercivity Kinetics Upon Step Annealing of Sintered Sm(Co0.88-xFexCu0.09Zr0.03)7 Magnets, J. Rare Earths, 2019, 37(10), p 1059-1065.10.1016/j.jre.2019.04.009 ↗
9. S. Romero, M. de Campos, J. de Castro, A. Moreira, and F. Landgraf, Microstructural Changes During the Slow-Cooling Annealing of Nanocrystalline SmCo 2:17 Type Magnets, J. Alloy. Compd., 2013, 551, p 312-317.10.1016/j.jallcom.2012.08.131 ↗
10. W. Sun, M.-G. Zhu, Y.-K. Fang, Z.-Y. Liu, Z.-H. Guo, and W. Li, Microstructures and Coercivity Mechanisms of 2-17-Type Sm-Co Magnets with High Remanence, Rare Met., 2015, 41, p 1353-1356.10.1007/s12598-015-0513-6 ↗
11. D. Vasilenko, D. Bratushev, A. Shitov, A. Popov, and D. Kolodkin, Control of the Properties of Sm-Fe-Co-Cu-Zr Magnets by the Method of Mixture of Powders, Met. Sci. Heat Treat., 2021, 62(9-10), p 560-565.10.1007/s11041-021-00603-x ↗
12. H. Khazdozian, J. Manzano, K. Gandha, I. Slowing, and I. Nlebedim, Recycled Sm-Co Bonded Magnet Filaments for 3D Printing of Magnets, AIP Adv., 2018, 8(5), p 056722.10.1063/1.5007669 ↗
13. A. Sarkar, M. Somashekara, M. Paranthaman, M. Kramer, C. Haase, and I. Nlebedim, Functionalizing Magnet Additive Manufacturing with In-Situ Magnetic Field Source, Addit. Manuf.. Manuf., 2020, 34, 101289.
14. A. Sarkar, M. Paranthaman, and I. Nlebedim, In-Situ Magnetic Alignment Model for Additive Manufacturing of Anisotropic Bonded Magnets, Addit. Manuf.. Manuf., 2021, 46, 102096.
15. A. Vucemilovic, M. Savary, and C. Espanet, 3D Printing of Multipolar Bonded SmCo Permanent Magnets, IEEE Trans. Mag., 2023, 59(11), p 1-7.10.1109/TMAG.2023.3289233 ↗
16. F. Bernier and J.-M. Lamarre, Metal-NdFeB Composite Permanent Magnets Produced by Cold Spray. EVS29 Symposium (2016)
17. J.-M. Lamarre and F. Bernier, Permanent Magnets Produced by Cold Spray Additive Manufacturing for Electric Engines, J. Therm. Spray Technol., 2019, 28, p 1709-1717.10.1007/s11666-019-00917-6 ↗
18. F. Bernier, M. Ibrahim, M. Mihai, Y. Thomas, and J.-M. Lamarre, Additive Manufacturing of Soft and Hard Magnetic Materials Used in Electrical Machines, Met. Powder Rep., 2020, 75, p 334-343.10.1016/j.mprp.2019.12.002 ↗
19. “Specification for Sintered Samarium Cobalt (SmCo) Permanent Magnets”, A1102, ASTM International (2019)
20. A. Arsenault, B. Charpentier-Pépin, A. Forcier, N. Nassiri, J. Bellemare, C. Lacroix, D. Ménard, F. Sirois, F. Bernier, and J.-M. Lamarre, “Largescale Vibrating Coil Magnetometer for the Magnetic Characterization of Bulk Superconductors, Rev. Sci. Instrum.Instrum., 2023, 94(8), p 085116.10.1063/5.0147920 ↗
21. A. Nourian, T. Schwartz, S. Boese, and S. Muftu, Effects of Process Parameters on Cold Spray Deposition of Al-6061 Alloy, J. Therm. Spray Technol., 2022, 31, p 2517-2536.10.1007/s11666-022-01456-3 ↗
22. R. Huang and H. Fukanuma, Study of the Influence of Particle Velocity on Adhesive Strength of Cold Spray Deposits, J. Therm. Spray Technol., 2011, 21, p 541-549.10.1007/s11666-011-9707-0 ↗
23. H. Kronmuller and D. Goll, Analysis of the Temperature Dependence of the Coercive Field of Sm2Co17 Based Magnets, Scripta Mater. Mater., 2003, 48(7), p 833-838.10.1016/S1359-6462(02)00619-X ↗
24. D. Goll, H. Kronmuller, and H. Stadelmaier, Micromagnetism and the Microstructure of High-Temperature Permanent Magnets, J. Appl. Phys., 2004, 96(11), p 6534-6545.10.1063/1.1809250 ↗
25. H. Kronmuller and D. Goll, “Modern Nanocrystalline/Nanostructured Hard Magnetic Materials, J. Magn. Magn. Mater.Magn. Magn. Mater., 2004, 272-276, p E319-E320.10.1016/j.jmmm.2003.11.384 ↗
26. H. Kronmuller and D. Goll, Coercivity of 2:17 Based Permanent Magnets, J. Iron. Steel Res. Int., 2006, 13, p 39-47.10.1016/S1006-706X(08)60159-4 ↗