journal article·2025-04Open access

Towards Highly Dense Yb-Silicate Microstructures Deposited by Air Plasma Spray for Environmental Barrier Coating Applications II: Plasma Gas Composition, Feedstock, and Anode Orifice Comparisons

Edward J. Gildersleeve, Emine Bakan, Robert Vaßen

Abstract

Abstract In all air plasma sprayed (APS) environmental barrier coating (EBC) applications, the predominant goal is to achieve maximum coating density, gas tightness, and/or hermeticity prior to subjecting it to harsh environments (i.e., high-temperature impingement of high-velocity water vapor). The microstructures of APS coatings are historically understood to be influenced by the input processing parameters. Beyond the local deposition rate (surface speed, feeding rate) explored in Part I, there are further extrinsic processing parameters such as plasma gas composition, feedstock choice, and anode orifice dimensions which can be tuned, but have not been fully explored in the context of EBCs. Screening these ancillary extrinsic inputs in a rigorous and systematic way presents challenges in determining which control variable(s) to select to gain meaningful insights. A constant particle temperature distribution (not average particle temperature) in the spray stream was held as a constraint, and the aforementioned extrinsic parameters were varied. As in Part I, a qualitative microstructural approach toward examining the presence (or absence) of advantageous vertical thin microcracks in the as-deposited coating was taken. For certain conditions, a Dense Vertically Macrocracked structure was achieved. Concurrent synthesis of these results offers further insights into process selection and parameter design can be gained.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: High-Temperature Coating Behaviors · Metal and Thin Film Mechanics · Advanced ceramic materials synthesis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (32)

Show source-provided references
1. N.S. Jacobson, E.J. Opila, and K.N. Lee, Oxidation and Corrosion of Ceramics and Ceramic Matrix Composites, Curr. Opin. Solid State Mater. Sci., 2001, 5(4), p 301-309.10.1016/S1359-0286(01)00009-2 ↗
2. E.J. Opila et al., SiC Recession Caused by SiO2 Scale Volatility under Combustion Conditions: II, Thermodynamics and Gaseous-Diffusion Model, J. Am. Ceram. Soc., 1999, 82(7), p 1826-1834.10.1111/j.1151-2916.1999.tb02005.x ↗
3. S. Sampath and X. Jiang, Splat Formation and Microstructure Development During Plasma Spraying: Deposition Temperature Effects, Mater. Sci. Eng. A, 2001, 304-306, p 144-150.10.1016/S0921-5093(00)01464-7 ↗
4. H. Herman, Plasma-Sprayed Coatings, Sci. Am., 1988, 259(3), p 112-117.10.1038/scientificamerican0988-112 ↗
5. H. Herman, Plasma Spray Deposition Processes, MRS Bull., 1988, 13(12), p 60-67.10.1557/S0883769400063715 ↗
6. S. Sampath and H. Herman, Rapid Solidification and Microstructure Development During Plasma Spray Deposition, J. Therm. Spray Technol., 1996, 5(4), p 445-456.10.1007/BF02645275 ↗
7. S.V. Shinde et al., Segmentation Crack Formation Dynamics During Air Plasma Spraying of Zirconia, Acta Mater., 2020, 183, p 196-206.10.1016/j.actamat.2019.10.052 ↗
8. S.V. Shinde and S. Sampath, Factors Governing Segmentation Crack Characteristics in Air Plasma Sprayed Ceramics, J. Eur. Ceram. Soc., 2022, 42(3), p 1077-1087.10.1016/j.jeurceramsoc.2021.10.064 ↗
9. R. Vassen, F. Traeger, and D. Stover, Correlation Between Spraying Conditions and Microcrack Density and Their Influence on Thermal Cycling Life of Thermal Barrier Coatings, J. Therm. Spray Technol., 2004, 13(3), p 396-404.10.1361/10599630420443 ↗
10. H.B. Guo, R. Vaßen, and D. Stöver, Atmospheric Plasma Sprayed Thick Thermal Barrier Coatings with High Segmentation Crack Density, Surf. Coat. Technol., 2004, 186(3), p 353-363.10.1016/j.surfcoat.2004.01.002 ↗
11. M. Karger, R. Vaßen, and D. Stöver, Atmospheric Plasma Sprayed Thermal Barrier Coatings with High Segmentation Crack Densities: Spraying Process, Microstructure and Thermal Cycling Behavior, Surf. Coat. Technol., 2011, 206(1), p 16-23.10.1016/j.surfcoat.2011.06.032 ↗
12. E. Bakan et al., Yb2Si2O7 Environmental Barrier Coatings Deposited by Various Thermal Spray Techniques: A Preliminary Comparative Study, J. Therm. Spray Technol., 2017, 26(6), p 1011-1024.10.1007/s11666-017-0574-1 ↗
13. E. Garcia, H. Lee, and S. Sampath, Phase and Microstructure Evolution in Plasma Sprayed Yb2Si2O7 Coatings, J. Eur. Ceram. Soc., 2019, 39(4), p 1477-1486.10.1016/j.jeurceramsoc.2018.11.018 ↗
14. B.T. Richards and H.N.G. Wadley, Plasma Spray Deposition of Tri-Layer Environmental Barrier Coatings, J. Eur. Ceram. Soc., 2014, 34(12), p 3069-3083.10.1016/j.jeurceramsoc.2014.04.027 ↗
15. B.T. Richards, H. Zhao, and H.N.G. Wadley, Structure, Composition, and Defect Control during Plasma Spray Deposition of Ytterbium Silicate Coatings, J. Mater. Sci., 2015, 50(24), p 7939-7957.10.1007/s10853-015-9358-5 ↗
16. R. Vaßen et al., Correlation of Process Conditions, Porosity Levels and Crystallinity in Atmospherically Plasma Sprayed Yb2Si2O7 Environmental Barrier Coatings, J. Compos. Sci., 2021, 5(8), p 198.10.3390/jcs5080198 ↗
17. S.V. Shinde and S. Sampath, Interplay Between Cracking and Delamination in Incrementally Deposited Plasma Sprayed Coatings, Acta Mater., 2021, 215, p 117074.10.1016/j.actamat.2021.117074 ↗
18. E. Bakan and R. Vaßen, Crack Healing Mechanisms in Atmospheric Plasma Sprayed Yb-silicate Coatings during Post-Process Heat Treatment, J. Eur. Ceram. Soc., 2023, 43(8), p 3684-3693.10.1016/j.jeurceramsoc.2023.02.005 ↗
19. E. Bakan, E.J. Gildersleeve V, and R. Vassen, Towards Highly Dense Yb-Silicate Microstructures Deposited by Air Plasma Spray for Environmental Barrier Coating Applications I: Influence of Local Deposition Rate. 2024: Under Review in the Journal of Thermal Spray Technology.10.1007/s11666-025-01969-7 ↗
20. E. Bakan et al., Plasma Sprayed Duplex Ytterbium Disilicate/Monosilicate EBCs and the Transformation from Ytterbia to Ytterbium Monosilicate during Burner Rig Testing, Corros. Sci., 2024, 235, p 112174.10.1016/j.corsci.2024.112174 ↗
21. P. Gougeon and C. Moreau, In-Flight Particle Surface Temperature Measurement: Influence of the Plasma Light Scattered by the Particles, J. Therm. Spray Technol., 1993, 2(3), p 229-233.10.1007/BF02650470 ↗
22. V. Srinivasan et al., Particle Injection in Direct Current Air Plasma Spray: Salient Observations and Optimization Strategies, Plasma Chem. Plasma Process., 2007, 27(5), p 609-623.10.1007/s11090-007-9089-8 ↗
23. H. Zhang et al., Melting Behavior of In-Flight Particles and Its Effects on Splat Morphology in Plasma Spraying, in ASME 2002 International Mechanical Engineering Congress and Exposition. 2002: New Orleans, Louisiana USA. p. 309-316.10.1115/IMECE2002-32514 ↗
24. W. Zhang and S. Sampath, A Universal Method for Representation of In-Flight Particle Characteristics in Thermal Spray Processes, J. Therm. Spray Technol., 2009, 18(1), p 23-34.10.1007/s11666-008-9214-0 ↗
25. P. Fauchais et al., Knowledge Concerning Splat Formation: An Invited Review, J. Therm. Spray Technol., 2004, 13(3), p 337-360.10.1361/10599630419670 ↗
26. E. Bakan et al., Effect of Processing on High-Velocity Water Vapor Recession Behavior of Yb-Silicate Environmental Barrier Coatings, J. Eur. Ceram. Soc., 2019, 39(4), p 1507-1513.10.1016/j.jeurceramsoc.2018.11.048 ↗
27. H. Wang et al., Microstructure and Phase Composition Evolution of Dual-Phase Ytterbium Silicate Coatings Plasma Sprayed from Stoichiometric Yb2Si2O7 Feedstock Powder, Surface Coat. Technol., 2022, 437, p 128373.10.1016/j.surfcoat.2022.128373 ↗
28. A. Lynam et al., Atmospheric Plasma Spraying of Ytterbium Disilicate for Abradable and Environmental Barrier Coatings: a Story of Processing-Microstructure Relationships, Ceram. Int., 2023, 49(13), p 22232-22243.10.1016/j.ceramint.2023.04.053 ↗
29. B. Li et al., Influence of Spraying Power on Microstructure, Phase Composition and Nanomechanical Properties of Plasma-Sprayed Nanostructured Yb-Silicate Environmental Barrier Coatings, Surf. Coat. Technol., 2024, 478, p 130450.10.1016/j.surfcoat.2024.130450 ↗
30. B. Pateyron et al., Thermodynamic and Transport Properties of Ar-H2 and Ar-He Plasma Gases used for Spraying at Atmospheric Pressure. I: Properties of the Mixtures, Plasma Chem. Plasma Process., 1992, 12(4), p 421-448.10.1007/BF01447253 ↗
31. E. Bakan, Y.J. Sohn, and R. Vaßen, Metastable to Stable Phase Transformation in Atmospheric Plasma Sprayed Yb-Silicate Coating During Post-Heat Treatment, Scripta Mater., 2023, 225, p 115169.10.1016/j.scriptamat.2022.115169 ↗
32. T.W. Clyne and S.C. Gill, Residual Stresses in Thermal Spray Coatings and Their Effect on Interfacial Adhesion: A Review of Recent Work, J. Therm. Spray Technol., 1996, 5(4), p 401.10.1007/BF02645271 ↗