journal article·2025-06Open access

Toward Highly Dense Yb-Silicate Microstructures Deposited by Air Plasma Spray for Environmental Barrier Coating Applications I: Influence of Local Deposition Rate

Emine Bakan, Edward J. Gildersleeve V, Robert Vaßen

Abstract

Abstract Environmental barrier coatings (EBCs) are used to shield high-temperature Si-based ceramic matrix composite gas turbine components from the harsh, water vapor-rich operating environment. The success of this application is directly correlated to the intrinsic gas tightness or hermeticity of the EBC volatilization barrier, which are typically rare-earth disilicates. For the air plasma-sprayed (APS) EBCs, the hermeticity is directly related to the processing parameters during deposition. In this work, the effect of surface speed and feeding rate on the microstructural evolution of plasma-sprayed Yb2Si2O7 coatings was studied. A qualitative assessment by means of microstructure analysis of hermeticity after crystallization heat treatment and the influence of the aforementioned processing parameters is discussed. It was found that utilizing lower feeding rates can minimize certain types of disadvantageous cracking in the as-deposited Yb2Si2O7 coatings. Moreover, at these low feeding rates (~1-5.4 g/min) regardless of the selected surface speed (250-1250 mm/s), highly dense Yb2Si2O7 microstructures could be obtained in the as-sprayed state. Contrastingly at higher feeding rates (~46.2 g/min), deleterious Yb2SiO5 band formation was observed at the top of each spray pass, which correlated to worsened cracking in the microstructures, particularly at low surface speed (250 mm/s). The monosilicate band formation was linked to the fine particle fraction of the feedstock (i.e., particles < 15 µm), and by sieving out this fraction the band formation could be eliminated when spraying at the higher feeding rate.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: High-Temperature Coating Behaviors · Advanced ceramic materials synthesis · Advanced materials and composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (41)

Show source-provided references
1. M. Belmonte, Advanced Ceramic Materials for High Temperature Applications, Adv. Eng. Mater., 2006, 8(8), p 693–703.10.1002/adem.200500269 ↗
2. R. Naslain and F. Christin, SiC-Matrix Composite Materials for Advanced Jet Engines, MRS Bull., 2011, 28(9), p 654–658.10.1557/mrs2003.193 ↗
3. M. Fellet and W. Rossner, Ceramic-Matrix Composites Take the Heat, MRS Bull., 2015, 40(11), p 916–918.10.1557/mrs.2015.283 ↗
4. N.P. Padture, Advanced Structural Ceramics in Aerospace Propulsion, Nat. Mater., 2016, 15(8), p 804–809.10.1038/nmat4687 ↗
5. N.S. Jacobson, E.J. Opila, and K.N. Lee, Oxidation and Corrosion of Ceramics and Ceramic Matrix Composites, Curr. Opin. Solid State Mater. Sci., 2001, 5(4), p 301–309.10.1016/S1359-0286(01)00009-2 ↗
6. E.J. Opila et al., SiC Recession Caused by SiO2 Scale Volatility Under Combustion Conditions: II, Thermodynamics and Gaseous-Diffusion Model, J. Am. Ceram. Soc., 1999, 82(7), p 1826–1834.10.1111/j.1151-2916.1999.tb02005.x ↗
7. K.N. Lee, R.A. Miller, and N.S. Jacobson, New Generation of Plasma-Sprayed Mullite Coatings on Silicon Carbide, J. Am. Ceram. Soc., 1995, 78(3), p 705–710.10.1111/j.1151-2916.1995.tb08236.x ↗
8. Eaton, H.E., et al. EBC Protection of SiC/SiC Composites in the Gas Turbine Combustion Environment. in ASME Turbo Expo 2000: Power for Land, Sea, and Air. 2000. American Society of Mechanical Engineers.10.1115/2000-GT-0631 ↗
9. Lee, K.N., Enviromental Barrier Coatings For SiC/SiC, in Ceramic Matrix Composites: Materials, Modeling and Technology, N.P. Bansal and J. Lamon, Editors. 2015, The American Ceramic Society.10.1002/9781118832998.ch15 ↗
10. B.T. Richards, M.R. Begley, and H.N.G. Wadley, Mechanisms of Ytterbium Monosilicate/Mullite/Silicon Coating Failure During Thermal Cycling in Water Vapor, J. Am. Ceram. Soc., 2015, 98(12), p 4066–4075.10.1111/jace.13792 ↗
11. B.T. Richards et al., Response of Ytterbium Disilicate–Silicon Environmental Barrier Coatings to Thermal Cycling in Water Vapor, Acta Mater., 2016, 106, p 1–14.10.1016/j.actamat.2015.12.053 ↗
12. E. Bakan et al., Yb2Si2O7 Environmental Barrier Coatings Deposited by Various Thermal Spray Techniques: A Preliminary Comparative Study, J. Therm. Spray Technol., 2017, 26(6), p 1011–1024.10.1007/s11666-017-0574-1 ↗
13. E. Garcia, H. Lee, and S. Sampath, Phase and Microstructure Evolution in Plasma Sprayed Yb2Si2O7 coatings, J. Eur. Ceram. Soc., 2019, 39(4), p 1477–1486.10.1016/j.jeurceramsoc.2018.11.018 ↗
14. K.N. Lee, Yb2Si2O7 Environmental Barrier Coatings with Reduced Bond Coat Oxidation Rates Via Chemical Modifications for Long Life, J. Am. Ceram. Soc., 2019, 102(3), p 1507–1521.10.1111/jace.15978 ↗
15. B.T. Richards, H. Zhao, and H.N.G. Wadley, Structure, Composition, and Defect Control During Plasma Spray Deposition of Ytterbium Silicate Coatings, J. Mater. Sci., 2015, 50(24), p 7939–7957.10.1007/s10853-015-9358-5 ↗
16. Z. Tian et al., Theoretical and Experimental Determination of the Major Thermo-Mechanical Properties of RE2SiO5 (RE = Tb, Dy, Ho, Er, Tm, Yb, Lu, and Y) for Environmental and Thermal Barrier Coating Applications, J. Eur. Ceram. Soc., 2016, 36(1), p 189–202.10.1016/j.jeurceramsoc.2015.09.013 ↗
17. E. Bakan, Y.J. Sohn, and R. Vaßen, Metastable to Stable Phase Transformation in Atmospheric Plasma Sprayed Yb-Silicate Coating During Post-Heat Treatment, Scripta Mater., 2023, 225, p 115169.10.1016/j.scriptamat.2022.115169 ↗
18. E. Garcia et al., Crystallization Behavior of Air-Plasma-Sprayed Ytterbium-Silicate-Based Environmental Barrier Coatings, J. Eur. Ceram. Soc., 2021, 41(6), p 3696–3705.10.1016/j.jeurceramsoc.2020.12.051 ↗
19. B.T. Richards and H.N.G. Wadley, Plasma Spray Deposition of Tri-Layer Environmental Barrier Coatings, J. Eur. Ceram. Soc., 2014, 34(12), p 3069–3083.10.1016/j.jeurceramsoc.2014.04.027 ↗
20. E. Bakan and R. Vaßen, Crack Healing Mechanisms in Atmospheric Plasma Sprayed Yb-Silicate Coatings During Post-Process Heat Treatment, J. Eur. Ceram. Soc., 2023, 43(8), p 3684–3693.10.1016/j.jeurceramsoc.2023.02.005 ↗
21. S. Kuroda and T.W. Clyne, The Quenching Stress in Thermally Sprayed Coatings, Thin Solid Films, 1991, 200(1), p 49–66.10.1016/0040-6090(91)90029-W ↗
22. Matejicek, J., S. Sampath, and H. Herman. Processing effects on splat formation, microstructure and quenching stress in plasma sprayed coatings. in ASM International, Thermal Spray: Meeting the Challenges of the 21 st Century. 1998.10.31399/asm.cp.itsc1998p0419 ↗
23. S.V. Shinde and S. Sampath, Interplay Between Cracking and Delamination in Incrementally Deposited Plasma Sprayed Coatings, Acta Mater., 2021, 215, p 117074.10.1016/j.actamat.2021.117074 ↗
24. M.D. Thouless, E. Olsson, and A. Gupta, Cracking of Brittle Films on Elastic Substrates, Acta Metall. Mater., 1992, 40(6), p 1287–1292.10.1016/0956-7151(92)90429-I ↗
25. J.L. Beuth, Cracking of Thin Bonded Films in Residual Tension, Int. J. Solids Struct., 1992, 29(13), p 1657–1675.10.1016/0020-7683(92)90015-L ↗
26. J. Ilavsky et al., Influence of Spray Angle on the Pore and Crack Microstructure of Plasma-Sprayed Deposits, J. Am. Ceram. Soc., 1997, 80(3), p 733–742.10.1111/j.1151-2916.1997.tb02890.x ↗
27. A. Kulkarni et al., Processing Effects on Porosity-Property Correlations in Plasma Sprayed Yttria-Stabilized Zirconia Coatings, Mater. Sci. Eng. A, 2003, 359(1), p 100–111.10.1016/S0921-5093(03)00342-3 ↗
28. S.-H. Leigh and C. Berndt Christopher, Quantitative Evaluation of Void Distributions Within a Plasma-Sprayed Ceramic, J. Am. Ceram. Soc., 2004, 82(1), p 17–21.10.1111/j.1151-2916.1999.tb01717.x ↗
29. E. Bakan et al., Effect of Processing on High-Velocity Water Vapor Recession Behavior of Yb-Silicate Environmental Barrier Coatings, J. Eur. Ceram. Soc., 2019, 39(4), p 1507–1513.10.1016/j.jeurceramsoc.2018.11.048 ↗
30. R. Vaßen et al., Correlation of Process Conditions, Porosity Levels and Crystallinity in Atmospherically Plasma Sprayed Yb2Si2O7 Environmental Barrier Coatings, J. Compos. Sci., 2021, 5(8), p 198.10.3390/jcs5080198 ↗
31. H. Wang et al., Microstructure and Phase Composition Evolution of Dual-Phase Ytterbium Silicate Coatings Plasma Sprayed From Stoichiometric Yb2Si2O7 Feedstock Powder, Surf. Coat. Technol., 2022, 437, p 128373.10.1016/j.surfcoat.2022.128373 ↗
32. A. Lynam et al., Atmospheric Plasma Spraying of Ytterbium Disilicate for Abradable and Environmental Barrier Coatings: A Story of Processing-Microstructure Relationships, Ceram. Int., 2023, 49(13), p 22232–22243.10.1016/j.ceramint.2023.04.053 ↗
33. B. Li et al., Influence of Spraying Power on Microstructure, Phase Composition and Nanomechanical Properties of Plasma-Sprayed Nanostructured Yb-Silicate Environmental Barrier Coatings, Surf. Coat. Technol., 2024, 478, p 130450.10.1016/j.surfcoat.2024.130450 ↗
34. E. Bakan et al., Plasma Sprayed Duplex Ytterbium Disilicate/Monosilicate EBCs and the Transformation from Ytterbia to Ytterbium Monosilicate During Burner Rig Testing, Corros. Sci., 2024, 235, p 112174.10.1016/j.corsci.2024.112174 ↗
35. P. Gougeon and C. Moreau, In-Flight Particle Surface Temperature Measurement: Influence of the Plasma Light Scattered by the Particles, J. Therm. Spray Technol., 1993, 2(3), p 229–233.10.1007/BF02650470 ↗
36. V. Srinivasan et al., Particle Injection in Direct Current Air Plasma Spray: Salient Observations and Optimization Strategies, Plasma Chem. Plasma Process., 2007, 27(5), p 609–623.10.1007/s11090-007-9089-8 ↗
37. S. Sampath and X. Jiang, Splat Formation and Microstructure Development During Plasma Spraying: Deposition Temperature Effects, Mater. Sci. Eng. A, 2001, 304–306, p 144–150.10.1016/S0921-5093(00)01464-7 ↗
38. P. Fauchais et al., Knowledge Concerning Splat Formation: An Invited Review, J. Therm. Spray Technol., 2004, 13(3), p 337–360.10.1361/10599630419670 ↗
39. T.W. Clyne and S.C. Gill, Residual Stresses in Thermal Spray Coatings and Their Effect on Interfacial Adhesion: A Review of Recent Work, J. Therm. Spray Technol., 1996, 5(4), p 401.10.1007/BF02645271 ↗
40. E.J. Gildersleeve and S. Sampath, Process-Geometry Interplay in the Deposition and Microstructural Evolution of 7YSZ Thermal Barrier Coatings by Air Plasma Spray, J. Therm. Spray Technol., 2020, 29(4), p 560–573.10.1007/s11666-020-01018-5 ↗
41. E. Pfender, Heat and Momentum Transfer to Particles in Thermal Plasma Flows, Pure Appl. Chem., 1985, 57(9), p 1179–1195.10.1351/pac198557091179 ↗