Single-Particle Impact of Ti6Al4V and Ti-5553 in Cold Spray: A Novel Approach to Flattening Ratio and Selecting Johnson–Cook Model Parameters
Source abstract
Abstract
Abstract The application of Finite Element Analysis (FEA) in cold spray (CS) provides valuable information about material deformation and stress distribution. The Johnson–Cook (JC) model is widely used to simulate material behavior, while the particle Flattening Ratio (FR) is commonly used to assess the deformation pattern and mechanism. FR has also been employed to evaluate and select appropriate JC model parameters. Experimental FR values can be obtained from a cross-sectional view of splats; however, the accuracy of these values can be affected by the sectioning location. This study introduces a novel approach for experimental FR observation by integrating top and cross-sectional views of Ti6Al4V and Ti-5553 deposited particle splats, addressing the limitations of the conventional cross-sectional FR method. The influence of the sectioning region on FR values was systematically evaluated through numerical and experimental analyses. Experimental FR results show that off-axis sectioning leads to overestimating FR values, with increases of 25.98% for Ti6Al4V and 15.45% for Ti-5553. The differences in critical velocities obtained using the FEA between the two FR measurement approaches were approximately 24.61% for Ti6Al4V and 32.46% for Ti-5553. The findings highlight the importance of accuracy in FR measurement and its effect on JC parameter selection and FEA results.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: High-Temperature Coating Behaviors · Nuclear Materials and Properties · Intermetallics and Advanced Alloy Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (46)
Show source-provided references
1. H. Zhou, S. Jiang, X. Li and C. Li, Deposition Behavior and Bonding Mechanism During Cold Spraying of Ti6Al4V on Different Substrates, Surf. Interfaces, 2022, 33, 102237. https://doi.org/10.1016/j.surfin.2022.10223710.1016/j.surfin.2022.102237 ↗
2. L.I. Perez-Andrade, V.S. Bhattiprolu, W.M. Schuette and L.N. Brewer, Influence of Powder Properties and Processing gas on the Microstructural Evolution of Armstrong CP-titanium and Ti6Al4V Powders Processed by Cold Spray, Surf. Coat. Technol., 2022 https://doi.org/10.1016/j.surfcoat.2021.12801110.1016/j.surfcoat.2021.128011 ↗
3. N. Ramachandiran, H. Asgari, F. Dibia, R. Eybe, W. Muhammad, A. Gerlich and E. Toyserkani, Effects of Post Heat Treatment on Microstructure and Mechanical Properties of Ti5553 Parts Made by Laser Powder Bed Fusion, J. Alloys Compd., 2023 https://doi.org/10.1016/j.jallcom.2022.16861610.1016/j.jallcom.2022.168616 ↗
4. M.J. Donachie, Titanium: A Technical Guide, 2nd ed., ASM International, 200010.31399/asm.tb.ttg2.9781627082693 ↗
5. J.C. Williams and R.R. Boyer, Opportunities and Issues in the Application of Titanium Alloys for Aerospace Components, Metals, 2020 https://doi.org/10.3390/met1006070510.3390/met10060705 ↗
6. C.J. Akisin, C.J. Bennett, F. Venturi, H. Assadi and T. Hussain, Numerical and Experimental Analysis of the Deformation Behavior of CoCrFeNiMn High Entropy Alloy Particles onto various Substrates During Cold Spraying, J. Therm. Spray Technol., 2022 https://doi.org/10.1007/s11666-022-01377-110.1007/s11666-022-01377-1 ↗
7. D. Boruah, B. Ahmad, T.L. Lee, S. Kabra, A.K. Syed, P. McNutt, M. Doré and X. Zhang, Evaluation of Residual Stresses Induced by Cold Spraying of Ti-6Al-4V on Ti-6Al-4V Substrates, Surf. Coat. Technol., 2019, 374, p 591–602. https://doi.org/10.1016/j.surfcoat.2019.06.02810.1016/j.surfcoat.2019.06.028 ↗
8. T. Suhonen, T. Varis, S. Dosta, M. Torrell and J.M. Guilemany, Residual Stress Development in Cold Sprayed Al, Cu and Ti Coatings, Acta Mater., 2013, 61(17), p 6329–6337. https://doi.org/10.1016/j.actamat.2013.06.03310.1016/j.actamat.2013.06.033 ↗
9. W.Y. Li, H. Liao, C.J. Li, G. Li, C. Coddet and X. Wang, On High Velocity Impact of Micro-Sized Metallic Particles in Cold Spraying, Appl. Surf. Sci., 2006, 253(5), p 2852–2862. https://doi.org/10.1016/j.apsusc.2006.05.12610.1016/j.apsusc.2006.05.126 ↗
10. H. Assadi, F. Gärtner, T. Stoltenhoff and H. Kreye, Bonding Mechanism in Cold Gas Spraying, Acta Mater., 2003, 51(15), p 4379–4394. https://doi.org/10.1016/S1359-6454(03)00274-X10.1016/S1359-6454(03)00274-X ↗
11. A. Fardan, C.C. Berndt and R. Ahmed, Numerical Modelling of Particle Impact and Residual Stresses in Cold Sprayed Coatings: A Review, Surf. Coat. Technol., 2021, 409, 126835. https://doi.org/10.1016/j.surfcoat.2021.12683510.1016/j.surfcoat.2021.126835 ↗
12. S. Yin, X. Wang, X. Suo, H. Liao, Z. Guo, W. Li and C. Coddet, Deposition Behavior of Thermally Softened Copper Particles in Cold Spraying, Acta Mater., 2013, 61(14), p 5105–5118. https://doi.org/10.1016/j.actamat.2013.04.04110.1016/j.actamat.2013.04.041 ↗
13. T. Schmidt, F. Gärtner, H. Assadi and H. Kreye, Development of a Generalized Parameter Window for Cold Spray Deposition, Acta Mater., 2006, 54(3), p 729–742. https://doi.org/10.1016/j.actamat.2005.10.00510.1016/j.actamat.2005.10.005 ↗
14. A.A. Tiamiyu and C.A. Schuh, Particle Flattening During Cold Spray: Mechanistic Regimes Revealed by Single Particle Impact Tests, Surf. Coat. Technol., 2020, 403, 126386. https://doi.org/10.1016/j.surfcoat.2020.12638610.1016/j.surfcoat.2020.126386 ↗
15. H. Assadi, T. Schmidt, H. Richter, J.-O. Kliemann, K. Binder, F. Gärtner, T. Klassen and H. Kreye, On Parameter Selection in Cold Spraying, J. Therm. Spray Technol., 2011, 20, p 1161–1176. https://doi.org/10.1007/s11666-011-9662-910.1007/s11666-011-9662-9 ↗
16. N.H. Tariq, L. Gyansah, J.Q. Wang, X. Qiu, B. Feng, M.T. Siddique and T.Y. Xiong, Cold Spray Additive Manufacturing: A Viable Strategy to Fabricate thick B4C/Al Composite Coatings for Neutron Shielding Applications, Surf. Coat. Technol., 2018, 339, p 224–236. https://doi.org/10.1016/j.surfcoat.2018.02.00710.1016/j.surfcoat.2018.02.007 ↗
17. X. Chu, R. Chakrabarty, H. Che, L. Shang, P. Vo, J. Song and S. Yue, Investigation of the Feedstock Deposition Behavior in a Cold Sprayed 316L/Fe Composite Coating, Surf. Coat. Technol., 2018, 337, p 53–62. https://doi.org/10.1016/j.surfcoat.2017.12.06310.1016/j.surfcoat.2017.12.063 ↗
18. X. Chu, H. Che, C. Teng, P. Vo and S. Yue, A Multiple Particle Arrangement Model to understand Cold Spray Characteristics of Bimodal Size 316L/Fe Powder Mixtures, Surf. Coat. Technol., 2020, 381, 125137. https://doi.org/10.1016/j.surfcoat.2019.12513710.1016/j.surfcoat.2019.125137 ↗
19. J.Y. Lek, A. Bhowmik, A.W.-Y. Tan, W. Sun, X. Song, W. Zhai, P.J. Buenconsejo, F. Li, E. Liu, Y.M. Lam and C.B. Boothroyd, Understanding the Microstructural Evolution of Cold Sprayed Ti-6Al-4V Coatings on Ti-6Al-4V Substrates, Appl. Surf. Sci., 2018, 459, p 492–504. https://doi.org/10.1016/j.apsusc.2018.07.17510.1016/j.apsusc.2018.07.175 ↗
20. S. Veeck, D. Lee, R. Boyer and R. Briggs, The Castability of Ti-5553 Alloy, Adv. Mater. Process., 2004, 162, p 47–49.
21. H. Petersen, The Properties of Helium: Density, Specific Heats, Viscosity, and Thermal Conductivity at Pressures from 1 to 100 Bar and from Room Temperature to About 1800 K, Risø National Laboratory, 1970
22. V.K.R. Sirigiri, V.Y. Gudiga, U.S. Gattu, G. Suneesh and K.M. Buddaraju, A Review on Johnson Cook Material Model, Mater. Today Proc., 2022 https://doi.org/10.1016/j.matpr.2022.04.27910.1016/j.matpr.2022.04.279 ↗
23. F. Ducobu, E. Rivière-Lorphèvre and E. Filippi, On the Importance of the Choice of the Parameters of the Johnson-Cook Constitutive Model and their Influence on the Results of a Ti6Al4V Orthogonal Cutting Model, Int. J. Mech. Sci., 2017, 122, p 143–155. https://doi.org/10.1016/j.ijmecsci.2017.01.00410.1016/j.ijmecsci.2017.01.004 ↗
24. R. Klopp, R. Clifton and T. Shawki, Pressure-Shear Impact and the Dynamic Viscoplastic Response of Metals, Mech. Mater., 1985, 4, p 375–385.10.1016/0167-6636(85)90033-X ↗
25. W. Lee and C. Lin, Plastic Deformation and Fracture Behaviour of Ti-6Al-4V Alloy Loaded with High Strain Rate Under Various Temperatures, Mater. Sci. Eng. A, 1998, 241, p 48–59.10.1016/S0921-5093(97)00471-1 ↗
26. W. Lee and C. Lin, High-Temperature Deformation Behaviour of Ti-6Al-4V Alloy Evaluated by High Strain-Rate Compression Tests, J. Mater. Process. Technol., 1998, 75, p 127–136.10.1016/S0924-0136(97)00302-6 ↗
27. T. Özel and E. Zeren, Identification of Constitutive Material Models Parameters for High-Strain Rate Metal Cutting Conditions Using Evolutionary Computational Algorithms, Mater. Manuf. Process., 2007, 22, p 659–667.10.1080/10426910701323631 ↗
28. T. Özel and E. Zeren, Determination of Work Material Flow Stress and Friction for FEA of Machining Using Orthogonal Cutting Tests, J. Mater. Process. Technol., 2004, 153–154, p 1019–1025.10.1016/j.jmatprotec.2004.04.162 ↗
29. G. Johnson, Strength and Fracture Characteristics of a Titanium Alloy (.06Al, .04V) Subjected to Various Strains, Strain Rates, Temperatures and Pressures, NSWC TR 86-144, Naval Surface Weapons Center, Dahlgren, VA, 1985
30. M. Dumitrescu, M. Elbestawi, and T. El-Wardany, Mist Coolant Applications in High Speed Machining of Advanced Materials, Metal Cutting and High Speed Machining, J. Paulo Davim, Ed., Kluwer Academic/Plenum Publishers, 2002, p 329–339
31. M. Calamaz, D. Coupard and F. Girot, A New Material Model for 2D Numerical Simulation of Serrated Chip Formation When Machining Titanium Alloy Ti-6Al-4V, Int. J. Mach. Tools Manuf, 2008, 48, p 275–288.10.1016/j.ijmachtools.2007.10.014 ↗
32. D. Bois and A. Grave, Simulation Numérique d′Essais d′Impact et Comparaison de Lois de Comportement (Numerical Simulation of Impact Tests and Comparison of Constitutive Laws), J. Phys., 1985, 46, p 101–108. ((in French))10.1051/jphys:01985004601010100 ↗
33. H.W. Meyer and D.S. Kleponis, Modeling the High Strain Rate Behavior of Titanium Undergoing Ballistic Impact and Penetration, Int. J. Impact Eng, 2001, 26, p 509–521.10.1016/S0734-743X(01)00107-5 ↗
34. L. Li and N. He, A FEA Study on Mechanisms of Saw-Tooth Chip Deformation in High Speed Cutting of Ti-6Al-4V Alloy, Proc. 5th Int. Conf. on High Speed Machining (HSM), 2006, p 759–767
35. T.B. Bouchnak, Étude du Comportement en Sollicitations Extrêmes et de l′Usinabilité d′un Nouvel Alliage de Titane Aéronautique: le Ti555-3 (Study of the Behaviour Under Extreme Loadings and Machinability of a New Aerospace Titanium Alloy: Ti555-3), Ph.D. Thesis, Arts et Métiers ParisTech – Centre de Angers, 2010 (in French)
36. D. Macdougall and J. Harding, A Constitutive Relation and Failure Criterion for Ti-5Al-3V Alloy at Impact Rates of Strain, J. Mech. Phys. Solids, 1999, 47, p 1157–1185.10.1016/S0022-5096(98)00086-6 ↗
37. S. Seo, O. Min and H. Yang, Constitutive Equation for Ti-6Al-4V at High Temperatures Measured Using the SHPB Technique, Int. J. Impact Eng, 2005, 31, p 735–754.10.1016/j.ijimpeng.2004.04.010 ↗
38. A. Khan, Y. Suh and R. Kazmi, Quasi-Static and Dynamic Loading Responses and Constitutive Modeling of Titanium Alloys, Int. J. Plast., 2004, 20, p 2233–2248.10.1016/j.ijplas.2003.06.005 ↗
39. G. Kay, Failure Modeling of Titanium Ti-6Al-4V and Aluminium 2024-T3 with the Johnson–Cook Material Model, Technical Report, U.S. Department of Energy, Lawrence Livermore National Laboratory, 200210.2172/15006359 ↗
40. S. Nemat-Nasser, W. Guo, V. Nesterenko, S. Indrakanti and Y. Gu, Dynamic Response of Conventional and Hot Isostatically Pressed Ti-6Al-4V Alloys: Experiments and Modeling, Mech. Mater., 2001, 33, p 425–439.10.1016/S0167-6636(01)00063-1 ↗
41. R. Bobbili and V. Madhu, Constitutive Modeling of Dynamic Flow Behavior of Ti-5553 Alloy, J. Alloys Compd., 2019, 787, p 260–266. https://doi.org/10.1016/j.jallcom.2019.02.10110.1016/j.jallcom.2019.02.101 ↗
42. G. Germain, A. Morel and T. Braham-Bouchnak, Identification of Material Constitutive Laws Representative of Machining Conditions for Two Titanium Alloys: Ti-6Al-4V and Ti-5553, J. Eng. Mater. Technol., 2013 https://doi.org/10.1115/1.402367410.1115/1.4023674 ↗
43. M.J. Donachie, Titanium: A Technical Guide, 2nd ed., ASM International, Materials Park, OH, 2000, ISBN: 0-87170-686-5
44. A.S. Alhulaifi and G.A. Buck, A Simplified Approach for the Determination of Critical Velocity for cold Spray Processes, J. Therm. Spray Technol., 2014, 23, p 1259–1269. https://doi.org/10.1007/s11666-014-0128-810.1007/s11666-014-0128-8 ↗
45. D. Goldbaum, J.M. Shockley, R.R. Chromik, A. Rezaeian, S. Yue, J.-G. Legoux and E. Irissou, The Effect of Deposition Conditions on Adhesion Strength of Ti and Ti-6Al-4V Cold Spray Splats, J. Therm. Spray Technol., 2011, 21, p 288–303. https://doi.org/10.1007/s11666-011-9720-310.1007/s11666-011-9720-3 ↗
46. P.C. King and M. Jahedi, Relationship Between Particle Size and Deformation in the Cold Spray Process, Appl. Surf. Sci., 2010, 256, p 1735–1738. https://doi.org/10.1016/j.apsusc.2009.09.10410.1016/j.apsusc.2009.09.104 ↗