Particle Impact Characteristics Influence on Cold Spray Bonding: Investigation of Interfacial Phenomena for Soft Particles on Hard Substrates
Source abstract
Abstract
The influence of particle impact temperature and size on adhesion of soft particle/hard substrate material in cold spray has been scarcely studied. While the relationship between particle impact conditions and particle/substrate bonding is commonly established through FEM studies, they typically lack comparison to experimental data. In the current study, characterization was performed by post-mortem observation of removed adhered particles and collected rebounded particles contact surfaces. Observations are correlated to interfacial pressure and temperature using FEM, otherwise impossible to measure in situ. The influence of pressure and its temporal evolution with particle deformation on melting and bonding is evaluated. Evidence of anisotropic particle deformation associated with microstructural orientation and grain geometrical features has been observed. Experimental evidence confirms that the particle south pole experiences restricted deformation as the original powder grain morphology was observed even after impact. Interfacial melt features have been detected and the melt zone generation, propagation, stagnation and regression tracked through FEM have shown important influence on single impact adhesion processes. Observed metallic bonding features and FEM indicate that increasing particle velocity, i.e., decreasing particle size, accelerates particle bonding processes to occur within tens of nanoseconds. Contact compressive pressure and interfacial expansion increase with particle increasing velocity and temperature.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: High-Temperature Coating Behaviors · Fluid Dynamics and Heat Transfer · Advanced ceramic materials synthesis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (61)
Show source-provided references
1. P.C. King, C. Busch, T. Kittel-Sherri, M. Jahedi and S. Gulizia, Interface Melding in Cold Spray Titanium Particle Impact, Surf. Coatings Technol., 2014, 239, p 191–199.10.1016/j.surfcoat.2013.11.039 ↗
2. G. Bae, S. Kumar, S. Yoon, K. Kang, H. Na, H.J. Kim and C. Lee, Bonding Features and Associated Mechanisms in Kinetic Sprayed Titanium Coatings, Acta Mater., 2009, 57(19), p 5654–5666.10.1016/j.actamat.2009.07.061 ↗
3. S. Sevsek, C. Haase, W. Bleck, S. Sevsek, C. Haase and W. Bleck, Strain-Rate-Dependent Deformation Behavior and Mechanical Properties of a Multi-Phase Medium-Manganese Steel, Metals (Basel), 2019, 9(3), p 344. https://doi.org/10.3390/met903034410.3390/met9030344 ↗
4. X.T. Luo, C.X. Li, F.L. Shang, G.J. Yang, Y.Y. Wang and C.J. Li, High Velocity Impact Induced Microstructure Evolution during Deposition of Cold Spray Coatings: A Review, Surf. Coat. Technol., 2014 https://doi.org/10.1016/j.surfcoat.2014.06.00610.1016/j.surfcoat.2014.06.006 ↗
5. S. Dosta, G. Bolelli, A. Candeli, L. Lusvarghi, I.G. Cano and J.M. Guilemany, Plastic Deformation Phenomena during Cold Spray Impact of WC-Co Particles onto Metal Substrates, Acta Mater., 2017, 124, p 173–181. https://doi.org/10.1016/J.ACTAMAT.2016.11.01010.1016/J.ACTAMAT.2016.11.010 ↗
6. M. Hassani-Gangaraj, D. Veysset, K.A. Nelson and C.A. Schuh, Impact-Bonding with Aluminum, Silver, and Gold Microparticles: Toward Understanding the Role of Native Oxide Layer, Appl. Surf. Sci., 2019, 476, p 528–532. https://doi.org/10.1016/J.APSUSC.2019.01.11110.1016/J.APSUSC.2019.01.111 ↗
7. D. Goldbaum, R.R. Chromik, N. Brodusch and R. Gauvin, Microstructure and Mechanical Properties of Ti Cold-Spray Splats Determined by Electron Channeling Contrast Imaging and Nanoindentation Mapping, Microsc. Microanal, 2015, 21, p 570–581. https://doi.org/10.1017/S143192761500024010.1017/S1431927615000240 ↗
8. A. Nastic, M. Vijay, A. Tieu, S. Rahmati and B. Jodoin, Experimental and Numerical Study of the Influence of Substrate Surface Preparation on Adhesion Mechanisms of Aluminum Cold Spray Coatings on 300M Steel Substrates. J. Therm. Spray Technol., 2017 26(7), p 1461–1483.10.1017/S1431927615000240 ↗
9. A.P. Semenov, The phenomenon of Seizure and Its Investigation, Wear, Elsevier, 1961, 4(1), p 1–9.10.1016/0043-1648(61)90236-8 ↗
10. H.A. Mohamed, J. Washburn, Mechanism of Solid State Pressure Welding. Weld. J. (1975). http://inis.iaea.org/Search/search.aspx?orig_q=RN:8330039. Accessed 21 Nov. 2020.
11. S. Rahmati and B. Jodoin, Physically Based Finite Element Modeling Method to Predict Metallic Bonding in Cold Spray, J. Therm. Spray Technol., 2020, 29(4), p 611–629.10.1007/s11666-020-01000-1 ↗
12. A. Nastic, M Vijay, A Tieu, S Rahmati, B Jodoin, Experimental and Numerical Study of the Influence of Substrate Surface Preparation on Adhesion Mechanisms of Aluminum Cold Spray Coatings on 300M Steel Substrates. J. Therm. Spray Technol. https://doi.org/10.1007/s11666-017-0602-1.10.1007/s11666-017-0602-1 ↗
13. W.Y. Li, C.J. Li and H. Liao, Significant Influence of Particle Surface Oxidation on Deposition Efficiency, Interface Microstructure and Adhesive Strength of Cold-Sprayed Copper Coatings, Appl. Surf. Sci., 2010, 256(16), p 4953–4958.10.1016/j.apsusc.2010.03.008 ↗
14. S. Yoon, Y. Xiong, H. Kim and C. Lee, Dependence of Initial Powder Temperature on Impact Behaviour of Bulk Metallic Glass in a Kinetic Spray Process, J. Phys. D Appl. Phys, 2009, 42, p 5. https://doi.org/10.1088/0022-3727/42/8/08200410.1088/0022-3727/42/8/082004 ↗
15. S. Yin, X. Wang, W. Li, H. Liao and H. Jie, Deformation Behavior of the Oxide Film on the Surface of Cold Sprayed Powder Particle, Appl. Surf. Sci., 2012, 259, p 294–300. https://doi.org/10.1016/J.APSUSC.2012.07.03610.1016/J.APSUSC.2012.07.036 ↗
16. K.H. Kim, W. Li and X. Guo, Detection of Oxygen at the Interface and Its Effect on Strain, Stress, and Temperature at the Interface between Cold Sprayed Aluminum and Steel Substrate, Appl. Surf. Sci., 2015, 357, p 1720–1726.10.1016/j.apsusc.2015.10.022 ↗
17. Y. Xie, S. Yin, C. Chen, M.P. Planche, H. Liao and R. Lupoi, New Insights into the Coating/Substrate Interfacial Bonding Mechanism in Cold Spray, Scr. Mater., 2016, 125, p 1–4.10.1016/j.scriptamat.2016.07.024 ↗
18. A. Ganesan, J. Affi, M. Yamada and M. Fukumoto, Bonding Behavior Studies of Cold Sprayed Copper Coating on the PVC Polymer Substrate, Surf. Coatings Technol., 2012, 207, p 262–269. https://doi.org/10.1016/J.SURFCOAT.2012.06.08610.1016/J.SURFCOAT.2012.06.086 ↗
19. S. Yin, X. Suo, Y. Xie, W. Li, R. Lupoi and H. Liao, Effect of Substrate Temperature on Interfacial Bonding for Cold Spray of Ni onto Cu, J. Mater. Sci., 2015, 50(22), p 7448–7457. https://doi.org/10.1007/s10853-015-9304-610.1007/s10853-015-9304-6 ↗
20. Y. Xie, C. Chen, M.-P. Planche, S. Deng, R. Huang, Z. Ren and H. Liao, Strengthened Peening Effect on Metallurgical Bonding Formation in Cold Spray Additive Manufacturing, J. Therm. Spray Technol., 2019, 28(4), p 769–779. https://doi.org/10.1007/s11666-019-00854-410.1007/s11666-019-00854-4 ↗
21. A. Sabard and T. Hussain, Bonding Mechanisms in Cold Spray Deposition of Gas Atomised and Solution Heat-Treated Al 6061 Powder by EBSD, 2018. https://arxiv.org/abs/1811.08694. Accessed 31 Jan 201910.1007/s10853-019-03736-w ↗
22. G. Bae, Y. Xiong, S. Kumar, K. Kang and C. Lee, General Aspects of Interface Bonding in Kinetic Sprayed Coatings, Acta Mater., 2008, 56(17), p 4858–4868.10.1016/j.actamat.2008.06.003 ↗
23. X.K. Suo, M. Yu, W.Y. Li, M.P. Planche and H.L. Liao, Effect of Substrate Preheating on Bonding Strength of Cold-Sprayed Mg Coatings, J. Therm. Spray Technol., 2012 https://doi.org/10.1007/s11666-012-9803-910.1007/s11666-012-9803-9 ↗
24. Y. Xie, M.P. Planche, R. Raoelison, H. Liao, X. Suo and P. Hervé, Effect of Substrate Preheating on Adhesive Strength of SS 316L Cold Spray Coatings, J. Therm. Spray Technol., 2016, 25(1-2), p 123–130. https://doi.org/10.1007/s11666-015-0312-510.1007/s11666-015-0312-5 ↗
25. W. Sun, A.W.Y. Tan, A. Bhowmik, I. Marinescu, X. Song, W. Zhai, F. Li and E. Liu, Deposition Characteristics of Cold Sprayed Inconel 718 Particles on Inconel 718 Substrates with Different Surface Conditions, Mater. Sci. Eng. A, 2018, 720, p 75–84.10.1016/j.msea.2018.02.059 ↗
26. R. Ortiz-Fernandez, S. Imbriglio, R. Chromik and B. Jodoin, The Role of Substrate Preheating on the Adhesion Strength of Cold-Sprayed Soft Particles on Hard Substrates, J. Therm. Spray Technol., 2021 https://doi.org/10.1007/s11666-020-01148-w10.1007/s11666-020-01148-w ↗
27. S. Yin, X. Wang, X. Suo, H. Liao, Z. Guo, W. Li and C. Coddet, Deposition Behavior of Thermally Softened Copper Particles in Cold Spraying, Acta Mater., 2013, 61(14), p 5105–5118.10.1016/j.actamat.2013.04.041 ↗
28. C. Chen, X. Xie, Y. Xie, M.-P. Planche, S. Deng, G. Ji, E. Aubry, Z. Ren and H. Liao, Cold Spraying of Thermally Softened Ni-Coated FeSiAl Composite Powder: Microstructure Characterization, Tribological Performance and Magnetic Property, Mater. Des., 2018, 160, p 270–283. https://doi.org/10.1016/J.MATDES.2018.09.02510.1016/J.MATDES.2018.09.025 ↗
29. Y. Xie, M.P. Planche, R. Raoelison, P. Hervé, X. Suo, P. He and H. Liao, Investigation on the Influence of Particle Preheating Temperature on Bonding of Cold-Sprayed Nickel Coatings, Surf. Coatings Technol., 2017, 318, p 99–105.10.1016/j.surfcoat.2016.09.037 ↗
30. A. Sova, S. Grigoriev, A. Kochetkova and I. Smurov, Influence of Powder Injection Point Position on Efficiency of Powder Preheating in Cold Spray: Numerical Study, Surf. Coatings Technol., 2014, 242, p 226–231.10.1016/j.surfcoat.2013.10.078 ↗
31. A. Nastic, B. Jodoin, D. Poirier and J.-G. Legoux, Particle Temperature Effect in Cold Spray: A Study of Soft Particle Deposition on Hard Substrate, Surf. Coatings Technol., 2021, 406, p 126735. https://doi.org/10.1016/j.surfcoat.2020.12673510.1016/j.surfcoat.2020.126735 ↗
32. Y. Cormier, P. Dupuis, B. Jodoin and A. Ghaei, Finite Element Analysis and Failure Mode Characterization of Pyramidal Fin Arrays Produced by Masked Cold Gas Dynamic Spray, J. Therm. Spray Technol., 2015, 24(8), p 1549–1565. https://doi.org/10.1007/s11666-015-0317-010.1007/s11666-015-0317-0 ↗
33. H. Jones, Microstructure of Rapidly Solidified Materials, Mater. Sci. Eng., 1984, 65(1), p 145–156. https://doi.org/10.1016/0025-5416(84)90208-810.1016/0025-5416(84)90208-8 ↗
34. A.M. Birt, V.K. Champagne, R.D. Sisson and D. Apelian, Microstructural Analysis of Ti-6Al-4V Powder for Cold Gas Dynamic Spray Applications, Adv. Powder Technol., 2015, 26(5), p 1335–1347. https://doi.org/10.1016/J.APT.2015.07.00810.1016/J.APT.2015.07.008 ↗
35. V.S. Bhattiprolu, K.W. Johnson, O.C. Ozdemir and G.A. Crawford, Influence of Feedstock Powder and Cold Spray Processing Parameters on Microstructure and Mechanical Properties of Ti-6Al-4V Cold Spray Depositions, Surf. Coatings Technol., 2018, 335, p 1–12. https://doi.org/10.1016/J.SURFCOAT.2017.12.01410.1016/J.SURFCOAT.2017.12.014 ↗
36. J. Lienhard, C. Crook, M.Z. Azar, M. Hassani, D.R. Mumm, D. Veysset, D. Apelian, K.A. Nelson, V. Champagne, A. Nardi, C.A. Schuh and L. Valdevit, Surface Oxide and Hydroxide Effects on Aluminum Microparticle Impact Bonding, Acta Mater., 2020, 197, p 28–39.10.1016/j.actamat.2020.07.011 ↗
37. H. Skoglund, M.K. Wedel and B. Karlsson, The Role of Oxygen in Powder Processing of FeAl, Intermetallics, 2003, 11(5), p 475–482.10.1016/S0966-9795(03)00024-4 ↗
38. W.Y. Li, H. Liao, C.J. Li, G. Li, C. Coddet and X. Wang, On High Velocity Impact of Micro-Sized Metallic Particles in Cold Spraying, Appl. Surf. Sci., 2006, 253(5), p 2852–2862.10.1016/j.apsusc.2006.05.126 ↗
39. S. Rahmati and A. Ghaei, The Use of Particle/Substrate Material Models in Simulation of Cold-Gas Dynamic-Spray Process. J. Therm. Spray Technol. 530–540 (2014)10.1007/s11666-013-0051-4 ↗
40. M.C. Price, A.T. Kearsley and M.J. Burchell, Validation of the Preston–Tonks–Wallace Strength Model at Strain Rates Approaching ∼1011 s-1 for Al-1100, Tantalum and Copper Using Hypervelocity Impact Crater Morphologies, Int. J. Impact Eng., 2013, 52, p 1–10.10.1016/j.ijimpeng.2012.09.001 ↗
41. J. Barbour, J. Knapp, D. Follstaedt, T. Mayer, K. Minor and D. Linam, The Mechanical Properties of Alumina Films Formed by Plasma Deposition and by Ion Irradiation of Sapphire, Nucl. Instruments Methods Phys. Res. Sect B Beam Interact. Mater. Atoms, 2000, 166-167, p 140–147. https://doi.org/10.1016/S0168-583X(99)00648-510.1016/S0168-583X(99)00648-5 ↗
42. S. Shin, S. Yoon, Y. Kim and C. Lee, Effect of Particle Parameters on the Deposition Characteristics of a Hard/Soft-Particles Composite in Kinetic Spraying, Surf. Coatings Technol., 2006, 201(6), p 3457–3461.10.1016/j.surfcoat.2006.07.255 ↗
43. C. Chen, X. Xie, Y. Xie, M.P. Planche, S. Deng, G. Ji, E. Aubry, Z. Ren and H. Liao, Cold Spraying of Thermally Softened Ni-Coated FeSiAl Composite Powder: Microstructure Characterization, Tribological Performance and Magnetic Property, Mater. Des., 2018, 160, p 270–283.10.1016/j.matdes.2018.09.025 ↗
44. J. Wu, H. Fang, S. Yoon, H. Kim and C. Lee, The Rebound Phenomenon in Kinetic Spraying Deposition, Scr. Mater., 2006, 54(4 SPEC. ISS.), p 665–669.10.1016/j.scriptamat.2005.10.028 ↗
45. P. Zhao, Q. Zhang, Y. Guo, H. Liu and Z. Deng, Atomic Simulation of Crystal Orientation Effect on Coating Surface Generation Mechanisms in Cold Spray, Comput. Mater. Sci., 2020, 184, p 109859.10.1016/j.commatsci.2020.109859 ↗
46. M. Razavipour, S. Rahmati, A. Zúñiga, D. Criado and B. Jodoin, Bonding Mechanisms in Cold Spray: Influence of Surface Oxidation During Powder Storage. https://doi.org/10.1007/s11666-020-01123-5.10.1007/s11666-020-01123-5 ↗
47. M. Hassani-Gangaraj, D. Veysset, V.K. Champagne, K.A. Nelson and C.A. Schuh, Adiabatic Shear Instability Is Not Necessary for Adhesion in Cold Spray, Scr. Mater., 2018, 158, p 430–439.
48. H. Assadi, F. Gärtner, T. Stoltenhoff and H. Kreye, Bonding Mechanism in Cold Gas Spraying, Acta Mater., 2003, 51(15), p 4379–4394.10.1016/S1359-6454(03)00274-X ↗
49. M. Grujicic, C. Zhao, W. DeRosset and D. Helfritch, Adiabatic Shear Instability Based Mechanism for Particles/Substrate Bonding in the Cold-Gas Dynamic-Spray Process, Mater. Des., 2004, 25(8), p 681–688.10.1016/j.matdes.2004.03.008 ↗
50. M.P. Dewar, A.G. McDonald and A.P. Gerlich, Interfacial Heating during Low-Pressure Cold-Gas Dynamic Spraying of Aluminum Coatings, J. Mater. Sci., 2012, 47(1), p 184–198. https://doi.org/10.1007/s10853-011-5786-z10.1007/s10853-011-5786-z ↗
51. A. Dorogoy and D. Rittel, Determination of the Johnson–Cook Material Parameters Using the SCS Specimen, Exp. Mech., 2009, 49(6), p 881–885. https://doi.org/10.1007/s11340-008-9201-x10.1007/s11340-008-9201-x ↗
52. A. Hänström and P. Lazor, High Pressure Melting and Equation of State of Aluminum, J. Alloys Compd., 2000, 305(1-2), p 209–215.10.1016/S0925-8388(00)00736-2 ↗
53. S. Chandra and P. Fauchais, Formation of Solid Splats During Thermal Spray Deposition, J. Therm. Spray Technol., 2009, 18(2), p 148–180. https://doi.org/10.1007/S11666-009-9294-510.1007/S11666-009-9294-5 ↗
54. C.-J. Li, C.-X. Li, G.-J. Yang and Y.-Y. Wang, Examination of Substrate Surface Melting-Induced Splashing during Splat Formation in Plasma Spraying, J. Therm. Spray Technol., 2006, 15(4), p 717–724. https://doi.org/10.1361/105996306X14694710.1361/105996306X146947 ↗
55. A. Ranjan, A. Islam, M. Pathak, M.K. Khan and A.K. Keshri, Plasma Sprayed Copper Coatings for Improved Surface and Mechanical Properties, Vacuum, Pergamon, 2019, 168, p 108834.10.1016/j.vacuum.2019.108834 ↗
56. M. Hassani, D. Veysset and C.A. Schuh, Melting Can Hinder Impact-Induced Adhesion, Artic. Phys. Rev. Lett., 2017 https://doi.org/10.1103/PhysRevLett.119.17570110.1103/PhysRevLett.119.175701 ↗
57. X. Song, J. Everaerts, W. Zhai, H. Zheng, A.W.Y. Tan, W. Sun, F. Li, I. Marinescu, E. Liu and A.M. Korsunsky, Residual Stresses in Single Particle Splat of Metal Cold Spray Process—Numerical Simulation and Direct Measurement, Mater. Lett., 2018, 230, p 152–156.10.1016/j.matlet.2018.07.117 ↗
58. T. Schmidt, H. Assadi, F. Gärtner, H. Richter, T. Stoltenhoff, H. Kreye and T. Klassen, From Particle Acceleration to Impact and Bonding in Cold Spraying, J. Therm. Spray Technol., 2009, 18(5-6), p 794–808. https://doi.org/10.1007/s11666-009-9357-710.1007/s11666-009-9357-7 ↗
59. K. Binder, J. Gottschalk, M. Kollenda, F. Gärtner and T. Klassen, Influence of Impact Angle and Gas Temperature on Mechanical Properties of Titanium Cold Spray Deposits, Journal of Thermal Spray Technology, 2011 https://doi.org/10.1007/s11666-010-9557-110.1007/s11666-010-9557-1 ↗
60. N. Bay, Mechanisms Producing Metallic Bonds in Cold Welding, Weld. J., 1983, 62(5), p 137.
61. S. Kumar, B.R. Bodapati, G. Vinay, K. Vamshi Kumar, N.M. Chavan, P. Suresh Babu, and A. Jyothirmayi, Estimation of Inter-Splat Bonding and Its Effect on Functional Properties of Cold Sprayed Coatings, Surf. Coatings Technol., Elsevier, 2021, 420, p 127318.10.1016/j.surfcoat.2021.127318 ↗